An Investigation of Lateral Surface Hardness and Related Cutting Forces in One-Directional Ultrasonic-Vibration Assisted Turning

2012 ◽  
Vol 445 ◽  
pp. 1041-1046
Author(s):  
Hamed Razavi ◽  
Mohammad Javad Nategh ◽  
H. Soleimanimehr
Keyword(s):  
Cutting Force ◽  
Lateral Surface ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Surface Hardness ◽  
Tangential Direction ◽  
Feed Speed ◽  
Machined Surface ◽  
Average Force ◽  
Tool Edge

The experimental investigation of UAT shows that the movement of cutting tool edge relative to the workpiece results from the cutting speed, feed speed and tools vibration in tangential direction affects the lateral machined surface of workpiece and leaves a repeating pattern of toothed regions on it. In UAT process, because of constant feed rate of tool toward workpiece, the cutting tool never separates from workpiece, though the tool rake face may separate periodically from chip in every cycle of vibration. This results in an increase in the surface hardness of the lateral machined surface in comparison with conventional turning (CT). The results of the present study confirm the advantage of UAT as far as the lower cutting force is concerned compared with CT. The higher surface hardness of the lateral surface observed in UAT causes the maximum cutting force to increase but the average force decreases with respect to CT.

Effect of Milling Parameters and Coolants on Surface Hardness of Tool Steel: SKD 11

2013 ◽  
Vol 650 ◽  
pp. 596-601
Author(s):  
Apichad Inkhamnoi ◽  
Komson Jirapattarasilp
Keyword(s):  
Tool Steel ◽  
Feed Rate ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Surface Hardness ◽  
Milling Process ◽  
Dry Cutting ◽  
Machined Surface ◽  
Milling Parameters ◽  
The Face

The purpose of this research was to study milling parameters and coolant, which were affecting to surface hardness of tool steel: SKD 11. The experiment was design by conduction of 3 factors and 3 levels. The parameters consisted of three levels of cutting speed and three levels of feed rate. Furthermore, the experiment was done by coolant types. Soluble oil vegetable oil and dry-cutting were used for coolant types in milling. The face milling process was chosen to experiment. Cutting tool was used for this study was inserted carbide with coated polycrystalline vapor deposited (PVD) tools. The finding of main factors and interaction between factors affected to surface hardness was analyzed. Effect of cutting speed and feed rate on surface hardness after milling was discussed. In order to finding suitable of coolant type, effect of coolants on hardness of machined surface was analyzed and compared.

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

High-Speed Capturing of Stress Distribution of Workpiece under Ultrasonically Assisted Cutting Condition

2014 ◽  
Vol 1017 ◽  
pp. 747-752
Author(s):  
Hiromi Isobe ◽  
Keisuke Hara
Keyword(s):  
Stress Distribution ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tool ◽  
Light Emission ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Photoelastic Method ◽  
Intermittent Cutting ◽  
Ultrasonic Vibration Cutting

This paper reports the stress distribution inside the workpiece under ultrasonic vibration cutting (UVC) condition. Many researchers have reported the improvement of tool wear, burr generation and surface integrity by reduction of time-averaged cutting force under UVC condition. However general dynamometers have an insufficient frequency band to observe the processing phenomena caused by UVC. In this paper, stress distribution inside the workpiece during UVC was observed by combining the flash light emission synchronized with ultrasonically vibrating cutting tool and the photoelastic method. Instantaneous stress distribution during UVC condition was observed. Because UVC induced an intermittent cutting condition, the stress distribution changed periodically and disappeared when the tool leaved from the workpiece. It was found that instantaneous maximum cutting force during UVC condition was smaller than quasi-static cutting force during conventional cutting when the cutting speed was less than 500 mm/min.

Research on Deep-hole Drilling Quality of High-strength Steel With Slender Gun Drill

2021 ◽  
Author(s):  
Jiabin Liang ◽  
Li Jiao ◽  
Pei Yan ◽  
Minghui Cheng ◽  
Tianyang Qiu ◽  
...  
Keyword(s):  
Cutting Force ◽  
High Strength Steel ◽  
Fluid Pressure ◽  
Cutting Speed ◽  
High Strength ◽  
Feed Speed ◽  
Machining Parameters ◽  
Deep Hole ◽  
Machining Quality ◽  
Gun Drill

Abstract There are a lot of problems exist in the processing of long and thin deep hole gun drilling of high strength steel, such as insufficient of the machining mechanism and characteristics of gun drilling, difficulty in selecting machining parameters, unknown influence mechanism of machining parameters on drilling force, drilling temperature and machining quality. In this paper, 42CrMo high strength steel is selected as the workpiece material. A numerical model of cutting force is established based on the mechanism of gun drill, and then the finite element simulation and processing test are carried out. The results show that the cutting force decreases with the increase of cutting speed, and increases with the increase of feed speed; the error between the theoretical and actual value is less than 10%. Cutting speed and feed speed have a great influence on machining quality, and the cutting fluid pressure mainly affects the surface roughness.

scholarly journals Experiments in the Machining of Ice at Negative Rake Angles

1984 ◽  
Vol 30 (104) ◽  
pp. 77-81 ◽  
Author(s):  
D.K. Lieu ◽  
C.D. Mote
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
Orthogonal Machining ◽  
Cutting Force Components ◽  
Force Components

AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1to 1 ms−1), and the rake angles (–15° to –60°). Results of the experiments showed that the cutting force components were approximately independent of cutting speed. The resultant cutting force on the tool was in a direction approximately normal to the cutting face of the tool. The magnitude of the resultant force increased with the negative rake angle. Photographs of ice-chip formation revealed continuous and segmented chips at different cutting depths.

Microtexture Generation Using Controlled Chatter Machining in Ultraprecision Diamond Turning

2015 ◽  
Vol 3 (2) ◽  
Author(s):  
Syed Adnan Ahmed ◽  
Jeong Hoon Ko ◽  
Sathyan Subbiah ◽  
Swee Hock Yeo
Keyword(s):  
Cutting Tool ◽  
Cutting Speed ◽  
Diamond Turning ◽  
Diamond Cutting ◽  
Machined Surface ◽  
Excited Vibration ◽  
Mass And Heat Transfer ◽  
Tool Shank ◽  
Diamond Cutting Tool

This paper describes a new method of microtexture generation in precision machining through self-excited vibrations of a diamond cutting tool. Conventionally, a cutting tool vibration or chatter is detrimental to the quality of the machined surface. In this study, an attempt is made to use the cutting tool's self-excited vibration during a cutting beneficially to generate microtextures. This approach is named as “controlled chatter machining (CCM).” Modal analysis is first performed to study the dynamic behavior of the cutting tool. Turning processes are then conducted by varying the tool holder length as a means to control vibration. The experimental results indicate that the self-excited diamond cutting tool can generate microtextures of various shapes, which depend on the cutting tool shank, cutting speed, feed, and cutting depth. The potential application of this proposed technique is to create microtextures in microchannels and microcavities to be used in mass and heat transfer applications.

Effect of Milling Speed and Feed on Surface Residual Stress of 7050-T7451 Aluminum Alloy

2012 ◽  
Vol 499 ◽  
pp. 217-222 ◽  
Author(s):  
C. Li ◽  
Yi Wan ◽  
R.R. Zhang ◽  
Zhan Qiang Liu
Keyword(s):  
Residual Stress ◽  
Aluminum Alloy ◽  
Cutting Speed ◽  
Diffraction Method ◽  
Cutting Condition ◽  
Feed Speed ◽  
X Ray Diffraction ◽  
Surface Residual Stress ◽  
Orthogonal Direction ◽  
Machined Surface

The residual stress in the milling of 7050-T7451 aluminum alloy was measured using X-ray diffraction method in which Psi-oscillation, Phi-oscillation and peak fit were adopted. Cutting speed and feed are main variables which were considered in this study. The results show that compressive residual stresses are generated in surface for the down milling generally, which is mainly due to burnishing effect between the tools flank face and the machined surface. In feed and its orthogonal direction, the effect of cutting speed and feed speed on residual stress is similar. Therefore, required residual stress can be achieved by controlling the cutting condition such as cutting speed, feed speed etc.

scholarly journals Investigation of AlCrN-Coated Inserts on Cryogenic Turning of Ti-6Al-4V Alloy

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1338
Author(s):  
Lakshmanan Selvam ◽  
Pradeep Kumar Murugesan ◽  
Dhananchezian Mani ◽  
Yuvaraj Natarajan
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
Physical Vapor Deposition ◽  
Metal Cutting ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machined Surface ◽  
Coated Carbide ◽  
Cryogenic Conditions

Over the past decade, the focus of the metal cutting industry has been on the improvement of tool life for achieving higher productivity and better finish. Researchers are attempting to reduce tool failure in several ways such as modified coating characteristics of a cutting tool, conventional coolant, cryogenic coolant, and cryogenic treated insert. In this study, a single layer coating was made on cutting carbide inserts with newly determined thickness. Coating thickness, presence of coating materials, and coated insert hardness were observed. This investigation also dealt with the effect of machining parameters on the cutting force, surface finish, and tool wear when turning Ti-6Al-4V alloy without coating and Physical Vapor Deposition (PVD)-AlCrN coated carbide cutting inserts under cryogenic conditions. The experimental results showed that AlCrN-based coated tools with cryogenic conditions developed reduced tool wear and surface roughness on the machined surface, and cutting force reductions were observed when a comparison was made with the uncoated carbide insert. The best optimal parameters of a cutting speed (Vc) of 215 m/min, feed rate (f) of 0.102 mm/rev, and depth of cut (doc) of 0.5 mm are recommended for turning titanium alloy using the multi-response TOPSIS technique.

A Study of Surface Integrity when Machining Refractory Titanium Alloys

2009 ◽  
Vol 83-86 ◽  
pp. 1059-1068 ◽  
Author(s):  
Armansyah Ginting ◽  
Mohammed Nouari ◽  
Nadhir Lebaal
Keyword(s):  
Surface Roughness ◽  
Titanium Alloys ◽  
Surface Integrity ◽  
Bulk Material ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Feed Speed ◽  
Machined Surface ◽  
Feed Mark ◽  
Coated Carbide

In this paper, the surface integrity is studied when machining the aeronautical titanium alloys. Surface roughness, lay, defects, microhardness and microstructure alterations are studied. The result of surface roughness judges that the CVD-coated carbide fails to produce better Ra value than the uncoated. Lay is characterized by cutting speed and feed speed directions. Feed mark, tearing surface, chip layer formation as built up layer (BUL), and deposited microchip are the defects. Microhardness is altered down to 350 microns beneath the machined surface. The first 50 microns is the soft sub-surface caused by thermal softening in ageing process. Microstructure alteration is observed in this sub-surface. Down to 200 microns is the hard sub-surface caused by the cyclic internal work hardening and then it is gradually decreasing to the bulk material hardness. It is concluded that dry machining titanium alloy is possible using uncoated carbide with cutting condition limited to finish or semi-finish for minimizing surface integrity alteration.

Study on Fractal Characterization Laws of Cutting Force in CNC Turning Aeronautic Aluminium Alloy 7075-T651

2017 ◽  
Vol 748 ◽  
pp. 224-228 ◽  
Author(s):  
Bao Liang Xing ◽  
Jing Wang ◽  
Hui Ying Cao ◽  
Shu Zhong Zhang ◽  
Wei Wei ◽  
...  
Keyword(s):  
Fractal Dimension ◽  
Aluminium Alloy ◽  
Cutting Force ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Fractal Dimensions ◽  
Feed Speed ◽  
Machining Parameters ◽  
Cutting Depth ◽  
Main Effect

Based on the experiment of turning aluminium alloy (7075-T651), the relations between the fractal dimensions of cutting forces with machining parameters are studied. Cutting speed, feed speed and cutting depth are considered as the process parameters. The cutting force in turning aluminium alloy operation are measured and the fractal dimension are calculated using the algorithm of correlation dimension. From main effect plots the fractal dimensions of three directions of cutting forces are reduced with the increase of cutting speed, increased with the increase of cutting depth and insignificant with the increase of feed speed. The mathematic models of fractal dimension of cutting force are developed using response surface methodology (RSM). The results of the ANOVA show that cutting speed and cutting depth have remarkable influence to fractal dimension Dx, Dy and Dz.

Sign in / Sign up

Export Citation Format

Share Document