Study on Performance of PP/POE In Situ Compatibilization

2012 ◽  
Vol 468-471 ◽  
pp. 1053-1057
Author(s):  
Yun Feng Yang ◽  
Guo Sheng Hu ◽  
Xing Lin Ren
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Impact Strength ◽  
Room Temperature ◽  
Dicumyl Peroxide ◽  
Maximum Value ◽  
Trimethylolpropane Triacrylate ◽  
In Situ Compatibilization ◽  
Temperature Impact

By the in situ compatibilization, PP/POE blends were prepared with dicumyl peroxide (DCP) as initiator, Trimethylolpropane triacrylate (TMPTA) as co-during systems and the metallocene polyolef in elastomers ploy (ethylene-1-octene) (POE) as toughening rubber. The effects of additive amount for TMPTA、POE on the mechanical properties were studied. The results showed that the maximum value of the room-temperature and low-temperature impact strength for the composite was reached to 52.03KJ/m2 and 37.29KJ/m2, and the elongationfor was reached to 482.74%.

Experimental Analysis on Strengthening Materials of Orthotropic Steel Bridge Decks

2010 ◽  
Vol 163-167 ◽  
pp. 132-136
Author(s):  
Yuan Qing Wang ◽  
Zong Wen Hu ◽  
Peng Pan ◽  
Yun Sheng Li ◽  
Yong Jiu Shi
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Impact Toughness ◽  
Performance Test ◽  
Southern China ◽  
Bridge Decks ◽  
Steel Bridge ◽  
Temperature Impact ◽  
Low Temperature Impact Toughness

Application of orthotropic steel bridge decks has become increasingly widespread, but with the growing traffic, the bridge decks frequently get fatigue damage, even forming cracks. This paper makes an overall analysis on the orthotropic steel bridge decks cracks of a certain bridge in Southern China, and experimentally studies on both in-situ and new strengthening materials, including low temperature impact toughness, conventional mechanical properties and fatigue performance. Test conclusions indicate that the two materials have good performance, which means the cracks have no business of in-situ materials, and the strengthening materials can be put into use.

scholarly journals Low-Temperature Mechanical Properties of High-Density and Low-Density Polyethylene and Their Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1821
Author(s):  
Ildar I. Salakhov ◽  
Nadim M. Shaidullin ◽  
Anatoly E. Chalykh ◽  
Mikhail A. Matsko ◽  
Alexey V. Shapagin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Impact Strength ◽  
Relative Elongation ◽  
High Density ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Elongation At Break ◽  
Subzero Temperatures ◽  
Izod Impact

Low-temperature properties of high-density polyethylene (HDPE), low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), and their blends were studied. The analyzed low-temperature mechanical properties involve the deformation resistance and impact strength characteristics. HDPE is a bimodal ethylene/1-hexene copolymer; LDPE is a branched ethylene homopolymer containing short-chain branches of different length; LLDPE is a binary ethylene/1-butene copolymer and an ethylene/1-butene/1-hexene terpolymer. The samples of copolymers and their blends were studied by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), 13С NMR spectroscopy, and dynamic mechanical analysis (DMA) using testing machines equipped with a cryochamber. It is proposed that such parameters as “relative elongation at break at −45 °C” and “Izod impact strength at −40 °C” are used instead of the ductile-to-brittle transition temperature to assess frost resistance properties because these parameters are more sensitive to deformation and impact at subzero temperatures for HDPE. LLDPE is shown to exhibit higher relative elongation at break at −45 °C and Izod impact strength at −20 ÷ 60 °C compared to those of LDPE. LLDPE terpolymer added to HDPE (at a content ≥ 25 wt.%) simultaneously increases flow properties and improves tensile properties of the blend at −45 °C. Changes in low-temperature properties as a function of molecular weight, MWD, crystallinity, and branch content were determined for HDPE, LLDPE, and their blends. The DMA data prove the resulting dependences. The reported findings allow one to understand and predict mechanical properties in the HDPE–LLDPE systems at subzero temperatures.

Mechanical properties of NiAl-Mo composites produced by specially controlled directional solidification

2012 ◽  
Vol 1516 ◽  
pp. 255-260 ◽  
Author(s):  
G. Zhang ◽  
L. Hu ◽  
W. Hu ◽  
G. Gottstein ◽  
S. Bogner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Directional Solidification ◽  
Creep Resistance ◽  
Room Temperature ◽  
Growth Direction ◽  
Nominal Composition ◽  
Potential Candidate ◽  
In Situ Composites

ABSTRACTMo fiber reinforced NiAl in-situ composites with a nominal composition Ni-43.8Al-9.5Mo (at.%) were produced by specially controlled directional solidification (DS) using a laboratory-scale Bridgman furnace equipped with a liquid metal cooling (LMC) device. In these composites, single crystalline Mo fibers were precipitated out through eutectic reaction and aligned parallel to the growth direction of the ingot. Mechanical properties, i.e. the creep resistance at high temperatures (HT, between 900 °C and 1200 °C) and the fracture toughness at room temperature (RT) of in-situ NiAl-Mo composites, were characterized by tensile creep (along the growth direction) and flexure (four-point bending, vertical to the growth direction) tests, respectively. In the current study, a steady creep rate of 10-6s-1 at 1100 °C under an initial applied tensile stress of 150MPa was measured. The flexure tests sustained a fracture toughness of 14.5 MPa·m1/2at room temperature. Compared to binary NiAl and other NiAl alloys, these properties showed a remarkably improvement in creep resistance at HT and fracture toughness at RT that makes this composite a potential candidate material for structural application at the temperatures above 1000 °C. The mechanisms responsible for the improvement of the mechanical properties in NiAl-Mo in-situ composites were discussed based on the investigation results.

scholarly journals Low-temperature degradation resistance and plastic deformation of ATZ ceramics stabilized by CaO

2021 ◽  
Vol 2103 (1) ◽  
pp. 012075
Author(s):  
AA Dmitrievskiy ◽  
DG Zhigacheva ◽  
VM Vasyukov ◽  
PN Ovchinnikov
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Plastic Deformation ◽  
Compressive Strength ◽  
Phase Composition ◽  
Low Temperature ◽  
Uniaxial Compression ◽  
Calcium Oxide ◽  
Tetragonal Phase ◽  
Room Temperature

Abstract In this work, the phase composition (relative fractions of monoclinic m-ZrO2, tetragonal t-ZrO2, and cubic c-ZrO2 phases) and mechanical properties (hardness, fracture toughness, compressive strength) of alumina toughened zirconia (ATZ) ceramics, with an addition of silica were investigated. Calcium oxide was used as a stabilizer for the zirconia tetragonal phase. It was shown that CaO-ATZ+SiO2 ceramics demonstrate increased resistance to low-temperature degradation. The plasticity signs at room temperature were found due to the SiO2 addition to CaO-ATZ ceramics. A yield plateau appears in the uniaxial compression diagram at 5 mol. % SiO2 concentration. It is hypothesized that discovered plasticity is due to the increased t→m transformability.

scholarly journals In situ environmental HRTEM discloses low temperature carbon soot oxidation by ceria–zirconia at the nanoscale

2019 ◽  
Vol 55 (27) ◽  
pp. 3876-3878 ◽  
Author(s):  
Eleonora Aneggi ◽  
Jordi Llorca ◽  
Alessandro Trovarelli ◽  
Mimoun Aouine ◽  
Philippe Vernoux
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Temperature ◽  
Room Temperature ◽  
Soot Oxidation ◽  
Environmental Transmission ◽  
Transmission Electron ◽  
Carbon Soot ◽  
Environmental Transmission Electron Microscopy

In situ environmental transmission electron microscopy discloses room temperature carbon soot oxidation by ceria–zirconia at the nanoscale.

scholarly journals Effects of Phase Morphology on Mechanical Properties: Oriented/Unoriented PP Crystal Combination with Spherical/Microfibrillar PET Phase

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 248 ◽  
Author(s):  
Dashan Mi ◽  
Yingxiong Wang ◽  
Maja Kuzmanovic ◽  
Laurens Delva ◽  
Yixin Jiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Ethylene Terephthalate ◽  
Phase Morphology ◽  
Mechanical Recycling ◽  
Immiscible Blends ◽  
Poly Ethylene Terephthalate ◽  
Poly Ethylene ◽  
The Impact

In situ microfibrillation and multiflow vibrate injection molding (MFVIM) technologies were combined to control the phase morphology of blended polypropylene (PP) and poly(ethylene terephthalate) (PET), wherein PP is the majority phase. Four kinds of phase structures were formed using different processing methods. As the PET content changes, the best choice of phase structure also changes. When the PP matrix is unoriented, oriented microfibrillar PET can increase the mechanical properties at an appropriate PET content. However, if the PP matrix is an oriented structure (shish-kebab), only the use of unoriented spherical PET can significantly improve the impact strength. Besides this, the compatibilizer polyolefin grafted maleic anhydride (POE-g-MA) can cover the PET in either spherical or microfibrillar shape to form a core–shell structure, which tends to improve both the yield and impact strength. We focused on the influence of all composing aspects—fibrillation of the dispersed PET, PP matrix crystalline morphology, and compatibilized interface—on the mechanical properties of PP/PET blends as well as potential synergies between these components. Overall, we provided a theoretical basis for the mechanical recycling of immiscible blends.

scholarly journals Effect of Diisocyanates as Compatibilizer on the Properties of BF/PBAT Composites by In Situ Reactive Compatibilization, Crosslinking and Chain Extension

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 806 ◽  
Author(s):  
Xiwei Xie ◽  
Caili Zhang ◽  
Yunxuan Weng ◽  
Xiaoqian Diao ◽  
Xinyu Song
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Phenyl Isocyanate ◽  
Chain Extension ◽  
Hydroxyl Group ◽  
Reactive Compatibilization ◽  
Carbamate Group ◽  
Bamboo Powder ◽  
Reactive Compatibilizer

Due to the hydrophobic nature of poly (butylene terephthalate) (PBAT), and the hydrophilic nature of bamboo flour (BF), a BF/PBAT (50/50) blend shows low mechanical properties, and especially shows poor impact strength. In order to increase the interfacial adhesion between BF and PBAT, diisocyanate was used as a reactive compatibilizer to modify bamboo powder. A series of BF/PBAT composites were prepared by the method of mixing and melting in an internal mixer. After adding reactive compatibilizer 4,4′-methylenebis(phenyl isocyanate) (MDI), BF/PBAT (50/50) composites with high mechanical properties were successfully prepared. The tensile strength, elongation at break, and impact strength of the BF/MDI-2/PBAT composite with 2 wt % MDI content were increased by 1.9, 6.8, and 4.3 times respectively over the BF/PBAT blend without the added MDI. The higher toughening effect of MDI in BF/PBAT composites can be mainly ascribed to the improved interface bonding between BF and PBAT. The isocyanate group of MDI can react with the hydroxyl group on the BF surface and in situ formation of the carbamate group on the BF surface. The residual isocyanate can then react with the hydroxyl group of PBAT and form carbamate groups. The rheological behaviors demonstrate that addition of appropriate amounts of MDI, 1 wt % and 2 wt %, can promote the flowability of the molten BF/PBAT composites due to the decrease in interparticle interaction between bamboo powder and the increase in the thermal motion of the molecules.

scholarly journals In Situ TEM Observations of Heavy Ion Damage in Gallium Arsenide

1988 ◽  
Vol 100 ◽  
Author(s):  
M. W. Bench ◽  
I. M. Robertson ◽  
M. A. Kirk
Keyword(s):  
Low Temperature ◽  
Room Temperature ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Heavy Ion ◽  
In Situ Tem ◽  
Accelerator Facility ◽  
Transmission Electron ◽  
Ion Accelerator

ABSTRACTTransmission electron microscopy experiments have been performed to investigate the lattice damage created by heavy-ion bombardments in GaAs. These experiments have been performed in situ by using the HVEN - Ion Accelerator Facility at Argonne National Laboratory. The ion bcorbardments (50 keV Ar+ and Kr+) and the microscopy have been carried out at temperatures rangrin from 30 to 300 K. Ion fluences ranged from 2 × 1011 to 5 × 1013 ions cm−2.Direct-inpact amorphization is observed to occur in both n-type and semi-insulating GaAs irradiated to low ion doses at 30 K and room temperature. The probability of forming a visible defect is higher for low temperature irradiations than for room temperature irradiations. The amorphous zones formed at low temperature are stable to temperatures above 250 K. Post implantation annealing is seen to occur at room temperature for all samples irradiated to low doses until eventually all visible damage disappears.

Compressive Plasticity of Zr-Based Bulk Metallic Glass at Low Temperature

2012 ◽  
Vol 443-444 ◽  
pp. 583-586
Author(s):  
Ya Juan Sun ◽  
Ri Ga Wu ◽  
Hong Jing Wang
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Metallic Glass ◽  
Bulk Metallic Glass ◽  
Low Temperatures ◽  
Room Temperature ◽  
Shear Bands ◽  
Strain Curve ◽  
Testing Temperature ◽  
Stress Strain Curve

The mechanical properties of a new Zr-based bulk metallic glass at low temperatures were investigated. The results indicate that the fracture strength increases significantly (4.9%) and the global plasticity increases somewhat when testing temperature is lowered to 123K. The stress-strain curve of the sample deformed exhibits more serrations and smaller stress drop due to formation of more shear bands at low temperature than at room temperature.

Sign in / Sign up

Export Citation Format

Share Document