Development of a Photovoltaic Powered Forced Convection Solar Dryer

2009 ◽  
Vol 62-64 ◽  
pp. 543-548 ◽  
Author(s):  
A.O. Adelaja ◽  
B.Y. Ogunmola ◽  
P.O. Akolade
Keyword(s):  
Fossil Fuel ◽  
Maximum Temperature ◽  
Solar Pv ◽  
Balance Equations ◽  
Pv Module ◽  
Transfer Equations ◽  
External Power ◽  
Solar Conversion ◽  
Forced Air ◽  
Air Circulation

This solar conversion system incorporates a suction fan powered by a solar PV module. Located at the outlet of the chamber is the d.c suction fan utilised to achieve forced air circulation without the use of external power supply like grid electricity, fossil fuel and battery. Simple thermal energy balance equations and heat transfer equations were employed in the design of the system. The operational efficiency of the collector is 83.2% and mass flow rate 1.58kg/min, the maximum temperature achieved in the chamber was 58oC. The system was used to dry vegetable, hydrophylum. The capital cost is less than $150.

scholarly journals Simulation of solar PV surface temperature with dimpled fin cooling

2022 ◽  
Vol 1217 (1) ◽  
pp. 012015
Author(s):  
M F Ibrahim ◽  
M S Misaran ◽  
N A Amaludin
Keyword(s):  
Temperature Drop ◽  
Solar Panel ◽  
Solar Irradiation ◽  
Solar Pv ◽  
Average Temperature ◽  
Pv Module ◽  
Air Convection ◽  
Percentage Difference ◽  
Experimental Works ◽  
Forced Air

Abstract A significant number of cooling technologies have been developed to maintain the PV module temperature within subscribed limits. This paper represents the simulation study of active cooling forced air convection with fins attached to the back of the solar panel using CFD SimScale software. It has been first carefully validated against experimental and numerical results available in the literature. The number of fins and the shape of perforated and dimpled in each fin were varied to compare cooling performance. Three types of fins were adapted into this simulation: traditional fins, circular, and triangle perforated/dimpled fins. The effect of solar irradiation and velocity inlet was also reviewed by applying the nominal operating condition from the experimental works. Results indicated that fin channels are a very effective cooling technique, which significantly reduces the average temperature of the PV cell, especially when increasing the number of fins from 20 to 26 fins. Also, the results show that the dimpled triangle fin had the highest average temperature drop with a percentage difference of 6% compared with the solar panel cooling with traditional fins.

scholarly journals A Review on Hybrid Solar PV Air Cooled Module

2021 ◽  
pp. 29-32
Author(s):  
Alok Kumar Singh ◽  
Dr Rajeev Arya ◽  
Shravan Vishwakarma
Keyword(s):  
Cooling System ◽  
Cell Damage ◽  
Water Immersion ◽  
Solar Pv ◽  
Heating Systems ◽  
Photovoltaic Modules ◽  
Industrial Setting ◽  
Improved Performance ◽  
Forced Air ◽  
Air Circulation

The cooling of the operating area is an essential operational factor to be taken into account in order to obtain greater efficiency in the operation of photovoltaic systems. Adequate cooling can improve electrical efficiency and reduce the rate of cell damage over time, which helps maximize the life of photovoltaic modules. The excess heat dissipated by the cooling system can be used in a domestic, commercial or industrial setting. Various cooling technologies are included in the review article: hybrid photovoltaic/heating systems cooled by forced air circulation, thermoelectric cooling system, water immersion cooling technology, and improved performance of solar modules using solar cells.

Parametric Study of Photovoltaic Thermal Solar Collector Using An Improved Parallel Flow

2020 ◽  
Vol 2 (1) ◽  
pp. 19-24
Author(s):  
Sakhr Mohammed Sultan ◽  
Chih Ping Tso ◽  
Ervina Efzan Mohd Noor ◽  
Fadhel Mustafa Ibrahim ◽  
Saqaff Ahmed Alkaff
Keyword(s):  
Thermal Conductivity ◽  
Energy Balance ◽  
Parametric Study ◽  
Solar Collector ◽  
Parallel Flow ◽  
Operating Conditions ◽  
Balance Equations ◽  
Conductivity Type ◽  
Pv Module ◽  
Sunny Weather

Photovoltaic Thermal Solar Collector (PVT) is a hybrid technology used to produce electricity and heat simultaneously. Current enhancements in PVT are to increase the electrical and thermal efficiencies. Many PVT factors such as type of absorber, thermal conductivity, type of PV module and operating conditions are important parameters that can control the PVT performance. In this paper, an analytical model, using energy balance equations, is studied for PVT with an improved parallel flow absorber. The performance is calculated for a typical sunny weather in Malaysia. It was found that the maximum electrical and thermal efficiencies are 12.9 % and 62.6 %, respectively. The maximum outlet water temperature is 59 oC.

scholarly journals Air circulation in a gastrointestinal light source box and endoscope in the era of SARS-CoV-2 and airborne transmission of microorganisms

2021 ◽  
Vol 09 (03) ◽  
pp. E482-E486
Author(s):  
Stanislas Chaussade ◽  
Einas Abou Ali ◽  
Rachel Hallit ◽  
Arthur Belle ◽  
Maximilien Barret ◽  
...  
Keyword(s):  
Light Source ◽  
Cooling System ◽  
Air Cooling ◽  
Airborne Transmission ◽  
Plastic Tube ◽  
Care Workers ◽  
Air Cooling System ◽  
Forced Air ◽  
Air Circulation ◽  
Closed Environment

Abstract Background and study aims The role that air circulation through a gastrointestinal endoscopy system plays in airborne transmission of microorganisms has never been investigated. The aim of this study was to explore the potential risk of transmission and potential improvements in the system. Methods We investigated and described air circulation into gastrointestinal endoscopes from Fujifilm, Olympus, and Pentax. Results The light source box contains a lamp, either Xenon or LED. The temperature of the light is high and is regulated by a forced-air cooling system to maintain a stable temperature in the middle of the box. The air used by the forced-air cooling system is sucked from the closed environment of the patient through an aeration port, located close to the light source and evacuated out of the box by one or two ventilators. No filter exists to avoid dispersion of particles outside the processor box. The light source box also contains an insufflation air pump. The air is sucked from the light source box through one or two holes in the air pump and pushed from the air pump into the air pipe of the endoscope through a plastic tube. Because the air pump does not have a dedicated HEPA filter, transmission of microorganisms cannot be excluded. Conclusions Changes are necessary to prevent airborne transmission. Exclusive use of an external CO2 pump and wrapping the endoscope platform with a plastic film will limit scatter of microorganisms. In the era of pandemic virus with airborne transmission, improvements in gastrointestinal ventilation systems are necessary to avoid contamination of patients and health care workers.

scholarly journals A Simple Mismatch Mitigating Partial Power Processing Converter for Solar PV Modules

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2308
Author(s):  
Kamran Ali Khan Niazi ◽  
Yongheng Yang ◽  
Tamas Kerekes ◽  
Dezso Sera
Keyword(s):  
Experimental Tests ◽  
Energy Yield ◽  
Power Electronic ◽  
Solar Pv ◽  
Partial Shading ◽  
Loss Analysis ◽  
Pv Systems ◽  
Pv Module ◽  
Pv Modules ◽  
In Series

Partial shading affects the energy harvested from photovoltaic (PV) modules, leading to a mismatch in PV systems and causing energy losses. For this purpose, differential power processing (DPP) converters are the emerging power electronic-based topologies used to address the mismatch issues. Normally, PV modules are connected in series and DPP converters are used to extract the power from these PV modules by only processing the fraction of power called mismatched power. In this work, a switched-capacitor-inductor (SCL)-based DPP converter is presented, which mitigates the non-ideal conditions in solar PV systems. A proposed SCL-based DPP technique utilizes a simple control strategy to extract the maximum power from the partially shaded PV modules by only processing a fraction of the power. Furthermore, an operational principle and loss analysis for the proposed converter is presented. The proposed topology is examined and compared with the traditional bypass diode technique through simulations and experimental tests. The efficiency of the proposed DPP is validated by the experiment and simulation. The results demonstrate the performance in terms of higher energy yield without bypassing the low-producing PV module by using a simple control. The results indicate that achieved efficiency is higher than 98% under severe mismatch (higher than 50%).

scholarly journals Analysis of Power Generation for Solar Photovoltaic Module with Various Internal Cell Spacing

2021 ◽  
Vol 13 (11) ◽  
pp. 6364
Author(s):  
June Raymond L. Mariano ◽  
Yun-Chuan Lin ◽  
Mingyu Liao ◽  
Herchang Ay
Keyword(s):  
Power Output ◽  
Spacing Effect ◽  
Photovoltaic Cell ◽  
Standard Test ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Engineering Software ◽  
Internal Cell ◽  
Cell Spacing ◽  
Pv Module

Photovoltaic (PV) systems directly convert solar energy into electricity and researchers are taking into consideration the design of photovoltaic cell interconnections to form a photovoltaic module that maximizes solar irradiance. The purpose of this study is to evaluate the cell spacing effect of light diffusion on output power. In this work, the light absorption of solar PV cells in a module with three different cell spacings was studied. An optical engineering software program was used to analyze the reflecting light on the backsheet of the solar PV module towards the solar cell with varied internal cell spacing of 2 mm, 5 mm, and 8 mm. Then, assessments were performed under standard test conditions to investigate the power output of the PV modules. The results of the study show that the module with an internal cell spacing of 8 mm generated more power than 5 mm and 2 mm. Conversely, internal cell spacing from 2 mm to 5 mm revealed a greater increase of power output on the solar PV module compared to 5 mm to 8 mm. Furthermore, based on the simulation and experiment, internal cell spacing variation showed that the power output of a solar PV module can increase its potential to produce more power from the diffuse reflectance of light.

scholarly journals Mathematical modeling and determination of thermodynamic properties of jabuticaba peel during the drying process

2016 ◽  
Vol 20 (6) ◽  
pp. 576-580 ◽  
Author(s):  
Cristian F. Costa ◽  
Paulo C. Corrêa ◽  
Jaime D. B. Vanegas ◽  
Fernanda M. Baptestini ◽  
Renata C. Campos ◽  
...  
Keyword(s):  
Experimental Data ◽  
Thermodynamic Properties ◽  
Drying Process ◽  
Drying Temperature ◽  
Air Temperatures ◽  
Nutritional Qualities ◽  
Forced Air ◽  
Air Circulation ◽  
Best Fit

ABSTRACT Jabuticaba is a fruit native of Brazil and, besides containing many nutritional qualities, it also has a good field for use in products such as flour for cakes and biscuits, juice, liqueur, jelly and others. This study aimed to model the drying kinetics and determine the thermodynamic properties of jabuticaba peel at different drying air temperatures. Ripe fruits of jabuticaba (Myrciaria jaboticaba) were collected and pulped manually. Drying was carried out in a forced-air circulation oven with a flow of 5.6 m s-1 at temperatures of 40, 50, 60 and 70 °C. Six mathematical models commonly used to represent the drying process of agricultural products were fitted to the experimental data. The Arrhenius model was used to represent the drying constant as a function of temperature. The Midilli model showed the best fit to the experimental data of drying. The drying constant increased with the increment in drying temperature and promoted an activation energy of 37.29 kJ mol-1. Enthalpy and Gibbs free energy decreased with the increase in drying temperature, while entropy decreased and was negative.

scholarly journals Design of a Building-Integrated Photovoltaic System with a Novel Bi-Reflector PV System (BRPVS) and Optimal Control Mechanism: An Experimental Study

Electronics ◽  
2018 ◽  
Vol 7 (7) ◽  
pp. 119 ◽  
Author(s):  
Muhammad Khan ◽  
Kamran Zeb ◽  
Waqar Uddin ◽  
P. Sathishkumar ◽  
Muhammad Ali ◽  
...  
Keyword(s):  
Low Cost ◽  
Input Voltage ◽  
Photovoltaic System ◽  
Solar Pv ◽  
Pv System ◽  
Building Integrated Photovoltaics ◽  
Pv Module ◽  
Solar Pv System ◽  
Zero Carbon ◽  
The Cost

Environment protection and energy saving are the most attractive trends in zero-carbon buildings. The most promising and environmentally friendly technique is building integrated photovoltaics (BIPV), which can also replace conventional buildings based on non-renewable energy. Despite the recent advances in technology, the cost of BIPV systems is still very high. Hence, reducing the cost is a major challenge. This paper examines and validates the effectiveness of low-cost aluminum (Al) foil as a reflector. The design and the performance of planer-reflector for BIPV systems are analyzed in detail. A Bi-reflector solar PV system (BRPVS) with thin film Al-foil reflector and an LLC converter for a BIPV system is proposed and experimented with a 400-W prototype. A cadmium–sulfide (CdS) photo-resistor sensor and an Arduino-based algorithm was developed to control the working of the reflectors. Furthermore, the effect of Al-foil reflectors on the temperature of PV module has been examined. The developed LLC converter confirmed stable output voltage despite large variation in input voltage proving its effectiveness for the proposed BRPVS. The experimental results of the proposed BRPVS with an Al-reflector of the same size as that of the solar PV module offered an enhancement of 28.47% in the output power.

A Two-Dimensional Conjugate Heat Transfer Model for Forced Air Cooling of an Electronic Device

1989 ◽  
Vol 111 (1) ◽  
pp. 41-45 ◽  
Author(s):  
A. Zebib ◽  
Y. K. Wo
Keyword(s):  
Heat Transfer ◽  
Conjugate Heat Transfer ◽  
Electronic Device ◽  
Transfer Problem ◽  
Maximum Temperature ◽  
Transfer Model ◽  
Air Cooling ◽  
Two Dimensional ◽  
Component Design ◽  
Forced Air

Thermal analysis of forced air cooling of an electronic component is modeled as a two-dimensional conjugate heat transfer problem. The velocity field in a constricted channel is first computed. Then, for a typical electronic module, the energy equation is solved with allowance for discontinuities in the thermal conductivity. Variation of the maximum temperature with the average air velocity is presented. The importance of our approach in evaluating possible benefits due to changes in component design and the limitations of the two-dimensional model are discussed.

scholarly journals Modeling of Photovoltaic Module Using the MATLAB

2019 ◽  
Vol 9 ◽  
pp. 59-69
Author(s):  
Alok Dhaundiyal ◽  
Divine Atsu
Keyword(s):  
Standard Test ◽  
Electrical Performance ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Pv Module ◽  
Proposed Model ◽  
Current Voltage ◽  
Pv Modules ◽  
The Impact ◽  
The Mathematical Model

This paper presents the modeling and simulation of the characteristics and electrical performance of photovoltaic (PV) solar modules. Genetic coding is applied to obtain the optimized values of parameters within the constraint limit using the software MATLAB. A single diode model is proposed, considering the series and shunt resistances, to study the impact of solar irradiance and temperature on the power-voltage (P-V) and current-voltage (I-V) characteristics and predict the output of solar PV modules. The validation of the model under the standard test conditions (STC) and different values of temperature and insolation is performed, as well as an evaluation using experimentally obtained data from outdoor operating PV modules. The obtained results are also subjected to comply with the manufacturer’s data to ensure that the proposed model does not violate the prescribed tolerance range. The range of variation in current and voltage lies in the domain of 8.21 – 8.5 A and 22 – 23 V, respectively; while the predicted solutions for current and voltage vary from 8.28 – 8.68 A and 23.79 – 24.44 V, respectively. The measured experimental power of the PV module estimated to be 148 – 152 W is predicted from the mathematical model and the obtained values of simulated solution are in the domain of 149 – 157 W. The proposed scheme was found to be very effective at determining the influence of input factors on the modules, which is difficult to determine through experimental means.

Sign in / Sign up

Export Citation Format

Share Document