Study Film Temperature Including Cavitation Effect of Sliding Bearing by CFD Method

2013 ◽  
Vol 690-693 ◽  
pp. 2012-2015 ◽  
Author(s):  
Fan Ming Meng ◽  
Tao Long
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Results ◽  
Vaporization Rate ◽  
Sliding Bearing ◽  
Cavitation Effect ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

The film temperature of sliding bearing considering the cavitation is studied based on the Rayleigh-Plesset (PRE) model with the computational fluid dynamics (CFD) method. The numerical results show that the maximum film temperature with the cavitation effect becomes smaller than that without the cavitation effect. The larger average vaporization rate of the film, the more decrease in the film temperature.

scholarly journals Validasi Model Turbulensi pada Simulasi Numerik Menggunakan Software Fluent dengan Sayap Onera M6

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Sulistiya Sulistiya ◽  
Alief Sadlie Kasman
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Computational Result ◽  
Computational Simulation ◽  
Turbulence Models ◽  
Wind Tunnels ◽  
Direct Testing ◽  
The World ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

AbstractNumerical simulation using Computational Fluid Dynamics (CFD) method is one way of predicting airflow characteristics on the model. This method is widely used because it is relatively inexpensive and faster in getting desired results compared with performing direct testing. The correctness of a computational simulation output is highly dependent on the input and how it was processed. In this paper, simulation is done on Onera M6 Wing, to investigate the effect of a turbulence model’s application on the accuracy of the computational result. The choice of Onera M6 Wing as a simulation’s model is due to its extensive database of testing results from various wind tunnels in the world. Among Turbulence models used are Spalart-Allmaras, K-Epsilon, K-Omega, and SST.Keywords: CFD, fluent, Model, Turbulence, Onera M6, Spalart-Allmaras, K-Epsilon, K-Omega, SST.AbstraksSimulasi numerik dengan menggunakan metode Computational Fluid Dynamics (CFD) merupakan salah satu cara untuk memprediksi karakteristik suatu aliran udara yang terjadi pada model. Metode ini banyak digunakan karena sifatnya yang relatif murah dan cepat untuk mendapatkan hasil dibandingkan dengan melakukan pengujian langsung. Benar tidak hasil sebuah simulasi komputasi sangat tergantung pada inputan yang diberikan serta cara memproses data inputan tersebut. Pada tulisan ini dilakukan simulasi dengan menggunakan sayap onera M6 dengan tujuan untuk mengetahui pengaruh penggunaan model turbulensi terhadap keakuratan hasil komputasi. Pilihan sayap onera M6 sebagai model simulasi dikarenakan model tersebut sudah memiliki database hasil pengujian yang cukup lengkap dan sudah divalidasi dari berbagai terowongan angin di dunia. Model turbulensi yang digunakan diantaranya Spalart-Allmaras, K-Epsilon, K-Omega dan SST.Kata Kunci : CFD, fluent, Model, Turbulensi, Onera M6, Spalart-Allmaras, K-Epsilon, K-Omega, SST.

scholarly journals An estimation of conditions inside construction works during a fire with the use of Computational Fluid Dynamics

2013 ◽  
Vol 61 (1) ◽  
pp. 155-160 ◽  
Author(s):  
G. Sztarbała
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Design Process ◽  
Fire Safety ◽  
Internal Environment ◽  
Preliminary Stage ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method ◽  
Construction Works

Abstract The aim of this paper is to present the application of Computational Fluid Dynamics (CFD) to the assessment of conditions inside construction works during a fire. The CFD method is now commonly used to support the design process of fire safety in construction works. This method is very useful at the preliminary stage of design because it is possible to check the internal environment during a fire and evaluate whether requirements of fire safety are met

Analysis and Simulation of Inner Flow Condition of a Novel Rotary on/off Valve

2012 ◽  
Vol 220-223 ◽  
pp. 1698-1702
Author(s):  
Jian Chen ◽  
Zhu Ming Su ◽  
Qi Zhou ◽  
Jian Ping Shu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Condition ◽  
High Speed ◽  
Ansys Fluent ◽  
Revolution Speed ◽  
Pressure Profiles ◽  
Open Case ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

A novel hydraulic rotary high speed on/off valve is investigated. The function of the outlet turbine and the effect on revolution speed of valve spool are analyzed. The inner fluid flow condition under full open case of the on/off valve is simulated using computational fluid dynamics(CFD) method based on Ansys/Fluent and velocity and pressure profiles of fluid inside valve are obtained. Suggestions on optimizing the geometry of valve to decrease transition losses are given.

An Investigation of Air-Cooled Steam Condenser Performance Under Windy Conditions Using Computational Fluid Dynamics

2011 ◽  
Vol 133 (6) ◽  
Author(s):  
M. T. F. Owen ◽  
D. G. Kröger
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Performance Evaluation ◽  
Test Data ◽  
Reliable Method ◽  
Numerical Results ◽  
Pressure Jump ◽  
Fan Performance ◽  
Computational Fluid Dynamics Cfd ◽  
Full Scale Tests

The development of an efficient and reliable method of evaluating the performance of an air-cooled steam condenser (ACC) under windy conditions using computational fluid dynamics (CFD) is presented. A two-step modeling approach is employed as a result of computational limitations. The numerical ACC model developed in this study makes use of the pressure jump fan model, among other approximations, in an attempt to minimize the computational expense of the performance evaluation. The accuracy of the numerical model is verified through a comparison of the numerical results to test data collected during full-scale tests carried out on an operational ACC. Good correlation is achieved between the numerical results and test data. The effect of wind on ACC performance at El Dorado Power Plant (Nevada, USA) is investigated. It is found that reduced fan performance due to distorted flow at the inlet of the upstream fans is the primary contributor to the reduction in ACC performance associated with increased wind speed in this case. The model developed in this study has the potential to allow for the evaluation of large ACC installations and provides a reliable platform from which further investigations into improving ACC performance under windy conditions can be carried out.

Application of CFD to evaluate the pore morphology effect on nanofluid flooding for enhanced oil recovery

RSC Advances ◽  
2015 ◽  
Vol 5 (37) ◽  
pp. 28938-28949 ◽  
Author(s):  
Reza Gharibshahi ◽  
Arezou Jafari ◽  
Ali Haghtalab ◽  
Mohammad Saber Karambeigi
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Recovery Factor ◽  
Pore Morphology ◽  
Morphology Effect ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

In this study a computational fluid dynamics (CFD) method has been developed to simulate the effect of pore morphology and its distribution in a 2D micromodel on the enhanced oil recovery factor of nanofluid flooding.

Numerical Investigation of Dusts Removal from Tramway Surface by Street Vacuum Sweeper

2011 ◽  
Vol 236-238 ◽  
pp. 1619-1622 ◽  
Author(s):  
Bo Fu Wu ◽  
Jin Lai Men ◽  
Jie Chen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Model ◽  
Pressure Drop ◽  
Removal Efficiency ◽  
Pressure Drops ◽  
Operational Safety ◽  
Airflow Field ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

In order to enhance the operational safety of tram vehicle and reduce the wear of guide wheels mounted on the vehicle, it is necessary to remove particles such as dusts and silts from tramway surface. The aim of this paper is to evaluate the effectiveness of street vacuum sweeper for sucking up dusts from tramway surface. A numerical model was developed based on dusts removal process. Under different pressure drops across the pickup head of the street vacuum sweeper, the flow field and dusts removal efficiency were analyzed with computational fluid dynamics (CFD) method. The numerical results show that a higher pressure drop can improve the airflow field in the pickup head and results in higher dusts removal efficiency, but higher pressure drop definitely need more energy. Therefore, a balance should be taken into consideration.

scholarly journals DESIGN AND ANALYSIS OF AN AERODYNAMIC DOWNFORCE PACKAGE FOR A FORMULA STUDENT RACE CAR

2017 ◽  
Vol 18 (2) ◽  
pp. 212-224
Author(s):  
Muhammad Abid ◽  
Hafiz Abdul Wajid ◽  
Muhammad Zohair Iqbal ◽  
Shayan Najam ◽  
Ali Arshad ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Tunnel ◽  
Experimental Studies ◽  
Numerical Results ◽  
Experimental Results ◽  
Race Car ◽  
Rear Wing ◽  
Computational Fluid Dynamics Cfd ◽  
Front Wing

This paper presents design of aerodynamic downforce generating devices (front wing, rear wing and diffuser) to enhance the performance of the Formula Student Race Car using numerical and experimental studies. Numerical results using computational fluid dynamics (CFD) studies were primarily validated with the experimental results performed in the wind tunnel. It was concluded that the use of a downforce package can enhance the performance of the vehicle in the competition.

Computational Fluid Dynamics Investigation on FCBGA Die Bulk Penetrating Cracks After Thermal Shock Test

2007 ◽  
Author(s):  
Kuo-Ying Tsai ◽  
Shih-Chang Ku
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Thermal Shock ◽  
Transient Analysis ◽  
Thermal Shock Test ◽  
Temperature Transition ◽  
Shock Test ◽  
Significant Temperature ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

A crack with unusual failure mode after thermal shock test (TST) is observed on the die bulk of certain bare-die FCBGA, in which the crack penetrates longitudinally within silicon die region. The computational fluid dynamics (CFD) method is introduced to investigate this phenomenon. The transient analysis results indicate a significant temperature difference existing between top and bottom surfaces of the silicon die in the very beginning of the liquid-to-liquid temperature transition. This could be fatal to a brittle material like silicon. Some possible solutions are then surveyed to alleviate the thermal impact to the FCBGA. At least one of enhanced proposals is proved effective to eliminate die crack occurrence after TST.

Influence Mechanisms of Manufacture Variations on Supersonic/Transonic Blade Aerodynamic Performances

2020 ◽  
Author(s):  
Baojie Liu ◽  
Jiaxin Liu ◽  
Xianjun Yu ◽  
Dejun Meng ◽  
Wenbin Shi
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Pressure ◽  
Statistical Analysis ◽  
Mach Number ◽  
Systematic Errors ◽  
Aerodynamic Performance ◽  
Aerodynamic Performances ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

Abstract The results of previous studies have proved that manufacture variations can cause a noticeable influence on compressor aerodynamic performance. The main objective of this paper is to investigate the influence rules and mechanisms of manufacture variations on supersonic/transonic blades aerodynamic performance. The variations used in this study were measured from some newly manufactured high-pressure compressors. In the present study, several blade sections with different design Mach number conditions are selected for further statistical analysis of measured deviation data. Therefore, some systematic errors in the deviation data have been revealed. Based on these data, the computational fluid dynamics (CFD) method has been used to obtain the aerodynamic performances of a large number of the measured blade elements. And then, the analysis of the influence rules of manufacture variations on blade aerodynamic performance in different Mach number conditions has been carried out. The present results indicate that the effects of manufacture variations on blade aerodynamic performance in the lower Mach number (0.8) condition are much more significant comparing to that in the higher Mach number (0.9∼1.2) conditions. Based on this, influence mechanisms of manufacture variations on positive incidence range and negative incidence range have been analyzed. The differences of influence mechanisms in different Mach number conditions are the focus of research.

Escort Tug Performance Prediction Using Computational Fluid Dynamics

2016 ◽  
Vol 60 (02) ◽  
pp. 61-77
Author(s):  
Brendan Smoker ◽  
Bart Stockdill ◽  
Peter Oshkai
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Separation ◽  
Travel Speed ◽  
Hydrodynamic Forces ◽  
Full Scale ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method ◽  
Thrust Forces ◽  
Steering Force

In this paper, we outline and validate a computational fluid dynamics (CFD) method for determining the hydrodynamic forces of an escort tug in indirect towing mode. We consider a range of yaw angles from 0° to 90° and a travel speed of 8 knots. We discuss the effects of scaling on prediction of flow separation and hydrodynamic forces acting on the vessel by carrying out CFD studies on both model and full-scale escort tugs performing indirect escort maneuvers. As the escort performance in terms of maximum steering forces is strongly dependent on the onset of flow separation from the hull and skeg of the tug, the model-scale simulations under-predict the maximum steering force by 12% relative to the full-scale simulations. In addition, we provide a method for converting the hydrodynamic forces of the CFD escort study into towline and thrust forces.

Sign in / Sign up

Export Citation Format

Share Document