Effect of Plant Fibres on the Variability of Cob Materials

2022 ◽  
Author(s):  
Junior Tchiotsop ◽  
Nabil Issaadi ◽  
Philippe Poullain ◽  
Stéphanie Bonnet
Keyword(s):  
Thermal Conductivity ◽  
Particle Size ◽  
Heat Capacity ◽  
Organic Matter ◽  
Thermal Properties ◽  
High Variability ◽  
Mean Values ◽  
Flax Fibres ◽  
Fibre Composites ◽  
Particle Screening

Earthen materials have different nature components and present a high variability comparing to conventional materials; researchers try to settle it down for a future normalization as environmentally efficient material. But there is a need in energy to do it, either directly (compaction, organic matter extraction, particle screening to get the best particle size distribution ...) or indirectly by including inefficient materials from an environmental perspective (cement, limestone ...). The aim of this study is to follow the variability problematic of cob materials by comparing and understanding variation level of the hygrothermal characteristics due to fibres nature and fibres content. We found that plant fibres (hemp, flax and hay) act as a stabilizer for dry bulk density; at 1% fibres substitute, hemp fibre composites show the highest coefficient of variation on the thermal properties (6.1% on thermal conductivity, 18.74% on specific heat capacity) but flax fibres show the highest mean values. Increasing hay stalk content induces the spread of the hygrothermal properties inside their range of variaation.

Effect of Nanosilica on Mechanical and Thermal Properties of Cement Composites for Thermal Energy Storage Materials

2015 ◽  
Vol 1131 ◽  
pp. 182-185
Author(s):  
Pongsak Jittabut
Keyword(s):  
Thermal Conductivity ◽  
Particle Size ◽  
Heat Capacity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Thermal Energy ◽  
Energy Storage Materials ◽  
Mechanical And Thermal Properties ◽  
Storage Materials ◽  
Nanosilica Particle

This research article presents the mechanical and thermal properties of cement-based composite for thermal energy storage materials. The effects of nanosilica particle size and concentration determined by mixing nanosilica particle size of 50 nm, using nanosilica were of 1-5 wt%. Thermal properties coefficients were tested using a direct measuring instrument with surface probe (ISOMET2114). The influence of nanosilica on the performance, such as compressive strength, bulk density, thermal conductivity, volume heat capacity and thermal diffusivity of hardened composite cement pastes were studied for future solar thermal energy materials with better performance. According to the development of thermal storage materials and their application environment requirement in solar thermal power, the specimens were subjected to heat at 350, and 900°C. It were observed that, before heating, the compressive strength is optimized at nanosilica amount of 4wt% at the age of 28 days. Moreover, after heating at 350 oC and 900°C, the thermal conductivity and volume heat capacity of the cement paste enriched with nanosilica were significantly lesser than that of the before heating one.

Determining Thermal Properties of Insulating Sleeves

2010 ◽  
Vol 649 ◽  
pp. 487-491 ◽  
Author(s):  
Witold K. Krajewski ◽  
Józef Szczepan Suchy
Keyword(s):  
Thermal Conductivity ◽  
Mass Transfer ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Boundary Conditions ◽  
Thermophysical Properties ◽  
Mean Values ◽  
Computer Aided ◽  
The Mean

The presented work is aimed at determining thermal diffusivity, thermal conductivity and heat capacity of insulating sleeves used in Polish metallurgical/foundry practice. On basis of the theory elaborated in [1] the mean values of thermophysical properties for temperatures range of about 150-1000 oC were obtained. The results obtained during the examinations presented in the paper can be helpful when formulating boundary conditions during the computer aided simulation of the processes of heat and mass transfer in the system: casting (ingot) – mould riser (ingot head) – ambient, which uses the investigated insulating sleeves [2, 3]. The method of determining thermal properties can be also used for other foundry materials, e.g. sands or cores.

scholarly journals Testing a Gypsum Composite Based on Raw Gypsum with a Direct Admixture of Paraffin and Polymer to Improve Thermal Properties

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3241
Author(s):  
Krzysztof Powała ◽  
Andrzej Obraniak ◽  
Dariusz Heim
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Phase Change ◽  
Large Scale ◽  
Building Materials ◽  
Residential Buildings ◽  
Energy Performance ◽  
Polymer Content ◽  
Volumetric Heat Capacity

The implemented new legal regulations regarding thermal comfort, the energy performance of residential buildings, and proecological requirements require the design of new building materials, the use of which will improve the thermal efficiency of newly built and renovated buildings. Therefore, many companies producing building materials strive to improve the properties of their products by reducing the weight of the materials, increasing their mechanical properties, and improving their insulating properties. Currently, there are solutions in phase-change materials (PCM) production technology, such as microencapsulation, but its application on a large scale is extremely costly. This paper presents a solution to the abovementioned problem through the creation and testing of a composite, i.e., a new mixture of gypsum, paraffin, and polymer, which can be used in the production of plasterboard. The presented solution uses a material (PCM) which improves the thermal properties of the composite by taking advantage of the phase-change phenomenon. The study analyzes the influence of polymer content in the total mass of a composite in relation to its thermal conductivity, volumetric heat capacity, and diffusivity. Based on the results contained in this article, the best solution appears to be a mixture with 0.1% polymer content. It is definitely visible in the tests which use drying, hardening time, and paraffin absorption. It differs slightly from the best result in the thermal conductivity test, while it is comparable in terms of volumetric heat capacity and differs slightly from the best result in the thermal diffusivity test.

Determination of the Thermal Properties of a PCB by Coupled Numerical and Experimental Approach

2020 ◽  
Author(s):  
Yener Usul ◽  
Mustafa Özçatalbaş
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Numerical Analysis ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Thermal Analyses ◽  
Analysis Model ◽  
Linear Temperature ◽  
Coefficient Of Thermal Conductivity

Abstract Increasing demand for usage of electronics intensely in narrow enclosures necessitates accurate thermal analyses to be performed. Conduction based FEM (Finite Element Method) is a common and practical way to examine the thermal behavior of an electronic system. First step to perform a numerical analysis for any system is to set up the correct analysis model. In this paper, a method for obtaining the coefficient of thermal conductivity and specific heat capacity of a PCB which has generally a complex composite layup structure composed of conductive layers, and dielectric layers. In the study, above mentioned properties are obtained performing a simple nondestructive experiment and a numerical analysis. In the method, a small portion of PCB is sandwiched from one side at certain pressure by jaws. A couple of linear temperature profiles are applied to the jaws successively. Unknown values are tuned in the analysis model until the results of FEM analysis and experiment match. The values for the coefficient of thermal conductivity and specific heat capacity which the experiment and numerical analysis results match can be said to be the actual values. From this point on, the PCB whose thermal properties are determined can be analyzed numerically for any desired geometry and boundary condition.

scholarly journals Mechanisms behind the enhancement of thermal properties of graphene nanofluids

Nanoscale ◽  
2018 ◽  
Vol 10 (32) ◽  
pp. 15402-15409 ◽  
Author(s):  
M. R. Rodríguez-Laguna ◽  
A. Castro-Alvarez ◽  
M. Sledzinska ◽  
J. Maire ◽  
F. Costanzo ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Specific Heat ◽  
Specific Heat Capacity

While the dispersion of nanomaterials is known to be effective in enhancing the thermal conductivity and specific heat capacity of fluids, the mechanisms behind this enhancement remain to be elucidated.

Influence of Mesocarp Fibre Inclusion on Thermal Properties of Foamed Concrete

2021 ◽  
Vol 87 (1) ◽  
pp. 1-11
Author(s):  
Siti Shahirah Suhaili ◽  
Md Azree Othuman Mydin ◽  
Hanizam Awang
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Volume Fraction ◽  
Thermal Constant ◽  
Volume Fractions ◽  
Foamed Concrete

The addition of mesocarp fibre as a bio-composite material in foamed concrete can be well used in building components to provide energy efficiency in the buildings if the fibre could also offer excellent thermal properties to the foamed concrete. It has practical significance as making it a suitable material for building that can reduce heat gain through the envelope into the building thus improved the internal thermal comfort. Hence, the aim of the present study is to investigate the influence of different volume fractions of mesocarp fibre on thermal properties of foamed concrete. The mesocarp fibre was prepared with 10, 20, 30, 40, 50 and 60% by volume fraction and then incorporated into the 600, 1200 and 1800 kg/m3 density of foamed concrete with constant cement-sand ratio of 1:1.5 and water-cement ratio of 0.45. Hot disk thermal constant analyser was used to attain the thermal conductivity, thermal diffusivity and specific heat capacity of foamed concrete of various volume fractions and densities. From the experimental results, it had shown that addition of mesocarp fibre of 10-40% by volume fraction resulting in low thermal conductivity and specific heat capacity and high the thermal diffusivity of foamed concrete with 600 and 1800 kg/m3 density compared to the control mix while the optimum amount of mesocarp fibre only limit up to 30% by volume fraction for 1200 kg/m3 density compared to control mix. The results demonstrated a very high correlation between thermal conductivity, thermal diffusivity and specific heat capacity which R2 value more than 90%.

A COMPREHENSIVE TISSUE PROPERTIES DATABASE PROVIDED FOR THE THERMAL ASSESSMENT OF A HUMAN AT REST

2010 ◽  
Vol 05 (03) ◽  
pp. 129-151 ◽  
Author(s):  
ROBERT L. MCINTOSH ◽  
VITAS ANDERSON
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Modeling ◽  
Blood Perfusion ◽  
Human Tissues ◽  
Tissue Properties ◽  
Future Studies ◽  
Average Value ◽  
Metabolic Heat

Accurate numerical calculation of the thermal profile in humans requires reliable estimates of the following five tissue properties: specific heat capacity (c), thermal conductivity (k), blood perfusion rates (m), metabolic heat production (A0), and density (ρ). A sixth property, water content (w, as a %), can also be used to estimate c and k. To date, researchers have used various and inconsistent estimates of these parameters, which hinders comparison of the corresponding results. In an effort to standardize and improve the accuracy of these parameters for future studies, we have documented over 150 key papers and books and developed a database of the six thermal properties listed above for 43 human tissues. For each tissue and each property the following were obtained: the average value, the number of source values, the minimum and maximum of source values, and the reference for each source value. A key premise for the development of the database was to only use references that provided the original measurements. This database is offered for use by the biological thermal modeling community to help improve the accuracy and consistency of thermal modeling results.

Thermal Properties of Selected Timbers

2014 ◽  
Vol 982 ◽  
pp. 100-103 ◽  
Author(s):  
Dana Koňáková ◽  
Monika Čáchová ◽  
Eva Vejmelková ◽  
Martin Keppert ◽  
Robert Černý
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Moisture Content ◽  
Specific Heat ◽  
Heat Transport ◽  
Specific Heat Capacity ◽  
Open Porosity ◽  
Building Structures ◽  
The Difference

This article deals with thermal properties of selected kinds of timber. Wood, generally, is one of often used natural materials in building structures. For our research, woods were selected according to frequency of utilization in civil engineering branch. Four different timbers were chosen, and experimental determinations of their properties were performed. Basic physical properties as well as thermal properties belong among studied characteristics. From achieved results, it is obvious, that the bulk density of studied wood ranges between 373 kg m-3 and 649 kg m-3, the open porosity differ by 13%. Regarding thermal properties, values of the thermal conductivity as well as the specific heat capacity are influenced mainly by the open porosity and moisture content. The thermal conductivity in dry state varies by about 31% while in the case of the specific heat capacity the difference is about 19%. Obtained date will be used in the mathematical analysis of heat transport in building structures.

scholarly journals Thermal and thermodynamic characterization of a dye powder from liquid turmeric extracts by spray drying

2016 ◽  
Vol 69 (1) ◽  
pp. 7845-7854 ◽  
Author(s):  
Aura Yazmin Coronel Delgado ◽  
Héctor José Ciro Velásquez ◽  
Diego Alonso Restrepo Molina
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Glass Transition ◽  
Thermal Properties ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Mass Loss ◽  
Spray Drying ◽  
Transient Flow ◽  
Sorption Isotherms

This study aimed to evaluate the thermodynamic properties of sorption isotherms and glass transition temperature (Tg) and the thermal properties of a dye powder obtained from turmeric extracts using spray drying. The sorption isotherms were evaluated at 15, 25 and 35 °C using the dynamic gravimetric method, wherein the isotherm data of the experiment were fit to GAB and BET models. Likewise, the Tg was measured using differential scanning calorimetry (DSC). Thermogravimetric analysis (TGA) was used to determine the mass loss, and the thermal properties (heat capacity, diffusivity and thermal conductivity) were determined using transient flow method. The results demonstrated that the GAB model best fit the adsorption data. The DSC analysis presented a glass transition temperature of 65.35 °C and a loss of volatiles at 178.07 °C. The TGA analysis indicated a considerable mass loss starting at 193 °C, resulting in degradation of the product. The thermal properties demonstrated a heat capacity of 2.45 J/g °C, a thermal conductivity of 0.164 ± 0.001 W/mK and a thermal diffusivity of 8.7x10-8 ± 0.000 m2/s.

scholarly journals Novel Dual Walling Cob Building: Dynamic Thermal Performance

Energies ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7663
Author(s):  
Kaoutar Zeghari ◽  
Ayoub Gounni ◽  
Hasna Louahlia ◽  
Michael Marion ◽  
Mohamed Boutouil ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Water Content ◽  
Wheat Straw ◽  
Numerical Study ◽  
Energy Performance ◽  
Climatic Conditions ◽  
Structural Walls ◽  
Hemp Shiv

This paper emphasizes the experimental and numerical study of new cob mixes used for insulation and load bearing wall elements. The experimental study provides complete datasets of thermal properties of the new walling materials, using cob with density ranging from 1107 kg/m3 to 1583 kg/m3 for structural walls and less than 700 kg m−3 for insulation walls. Various mixes of French soils and fibres (reed, wheat straw, hemp shiv, hemp straw, and flax straw) with different water contents are studied. The lowest average thermal conductivity is obtained for the structural cob mix prepared of 5% wheat straw and 31% of water content. The insulation mix, prepared with 25% reed and 31% water content, has the lowest thermal conductivity. Investigation of diffusivity, density, and heat capacity shows that, when thermal conductivity is lower than 0.4 W m−1 K−1, the decrease in cob density leads to better insulation values and higher heat capacity. Little variation is noticed regarding the density and heat capacity for cob mixes with thermal conductivity higher than 0.4 W m−1 K−1. Furthermore, the non-uniformity of local thermal conductivity and heat losses through the samples is due mainly to the non-uniform distribution of fibres inside the mixes inducing an increase in heat loss up to 50% for structural walls and 25% for insulation walls. Cob thermal properties are used in a comparative simulation case study of a typical house under French and UK climatic conditions. The energy performance of the conventional building is compared to a dual walled cob building, showing remarkable reduction in energy consumption as the cob walls, whilst maintaining comfortable indoor conditions without additional heating.

Sign in / Sign up

Export Citation Format

Share Document