Synthesis and Characterization of Hydroxyapatite Powder from Natural Bovine Bone

2014 ◽  
Vol 19 ◽  
pp. 35-42 ◽  
Author(s):  
Muhammad Wasim ◽  
Rameez Saeed Malik ◽  
Muhammad Usman Tufail ◽  
Ahsan Ullah Jutt ◽  
Rafiq Ahmad ◽  
...  
Keyword(s):  
Thermal Decomposition ◽  
Xrd Analysis ◽  
Bovine Bone ◽  
X Ray Diffraction ◽  
Powder Xrd Analysis ◽  
Key Words Hydroxyapatite ◽  
Ft Ir ◽  
Ft Ir Spectroscopy ◽  
Additional Phase

Hydroxyapatite was synthesized from bovine cortical bone by thermal decomposition method. The chemically cleaned bone was heated to 160 °C for 48 hour to remove moisture and any organic contents followed by decomposition in muffle furnace at 850 °C for 6 hours. The so-obtained white powder was characterized by Fourier Transform Infrared (FT-IR) spectroscopy and X-Ray Diffraction (XRD), SEM and EDX method. The FT-IR results proved the existence of hydroxyl (OH-) and phosphate (PO4-3) groups in the powder. XRD analysis was in support to the FT-IR spectrum, however, an additional phase of tri-calcium phosphate (TCP) was also observed as an impurity, SEM shows the surface morphology & EDX gives the Calcium (Ca) to Phosphorous (P) ratio. Key Words: Hydroxyapatite; Thermal Decomposition, Calcination

scholarly journals Preparation and Characterization of Cetyl Trimethylammonium Intercalated Sericite

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Hao Ding ◽  
Yuebo Wang ◽  
Yu Liang ◽  
Faxiang Qin
Keyword(s):  
Ion Exchange ◽  
Interlayer Space ◽  
Xrd Analysis ◽  
Acid Activation ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

Intercalated sericite was prepared by intercalation of cetyl trimethylammonium bromide (CTAB) into activated sericite through ion exchange with the following two steps: the activation of sericite by thermal modification, acid activation and sodium modification; the ion exchange intercalation of CTA+into activated sericite. Effects of reaction time, reaction temperature, CTAB quantity, kinds of medium, and aqueous pH on the intercalation of activated sericite were examined by X-ray diffraction (XRD) analysis, Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The results indicated that the CTA+entered sericite interlayers and anchored in the aluminosilicate interlayers through strong electrostatic attraction. The arrangement of CTA+in sericite interlayers was that alkyl chain of CTA+mainly tilted at an angle about 60° (paraffin-type bilayer) and 38° (paraffin-type monolayer) with aluminosilicate layers. The largest interlayer space was enlarged from 0.9 nm to 5.2 nm. The intercalated sericite could be used as an excellent layer silicate to prepare clay-polymer nanocomposites.

Preparation and Characterization of Cefradine/Montmorillionite Composites

2012 ◽  
Vol 560-561 ◽  
pp. 434-437 ◽  
Author(s):  
Lan Wang ◽  
Wen Ji Guo ◽  
Yan Zhao Zhao
Keyword(s):  
Gastric Fluid ◽  
Simulated Gastric Fluid ◽  
X Ray Diffraction ◽  
Simulated Intestinal Fluid ◽  
Solution Intercalation ◽  
Method Of Solution ◽  
Ft Ir ◽  
In The Beginning ◽  
Ft Ir Spectroscopy

The objective of this paper was to prepare the composite of crefradine/montmorillionite in the method of solution intercalation. The drug load and intercalation rate varied with the drug concentration. X-ray diffraction (XRD), Fourier transformed infrared (FT-IR) Spectroscopy, and thermal analysis (TG-DSC) were applied to characterize composite mentioned above. Together with drug release tests, results indicate cefradine intercalated into montmorillionite.The release profiles of cefradine/MMT in simulated gastric fluid (pH 1.2) and simulated intestinal fluid (pH 7.4) at 37°Cduring 10h are shown in Fig. 4. The amount of cefradine in the beginning 2h came up to 35% and 50%, and in the following time, cefradine released slowly. The release behaviors met the requirements of sustained release.

scholarly journals An Efficient and Novel Ammonia Sensor Based on Polypyrrole/Tin Oxide/MWCNT Nanocomposite

2020 ◽  
Vol 32 (6) ◽  
pp. 1505-1510
Author(s):  
Ahmad Husain ◽  
Mohd Urooj Shariq ◽  
Anees Ahmad
Keyword(s):  
Electron Microscopy ◽  
Tin Oxide ◽  
Charge Carriers ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Ammonia Sensing ◽  
Transmission Electron ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

In present study, the synthesis and characterization of a novel polypyrrole (PPy)/tin oxide (SnO2)/MWCNT nanocomposite along with pristine polypyrrole is reported. These materials have been studied for their structural and morphological properties by FT-IR spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. PPy/SnO2/MWCNT nanocomposite has been converted into a pellet-shaped sensor, and its ammonia sensing studies were carried out by calculating the variation in the DC electrical conductivity at different concentration of ammonia ranging from 10 to 1500 ppm. The sensing response of the sensor was determined at 1500, 1000, 500, 200, 100 and 10 ppm and found to be 70.4, 66.1, 62.2, 55.4, 50.8 and 39.7%, respectively The sensor showed a complete reversibility at lower concentrations along with excellent selectivity and stability. Finally, a sensing mechanism was also proposed involving polarons (charge carriers) of polypyrrole and lone pairs of ammonia molecules

scholarly journals Synthesis, Spectral, Structural and Thermal Characterization of Inorganic Crystal: Phenyl Trimethylammonium Tetrachlorocobaltate

2019 ◽  
Vol 31 (8) ◽  
pp. 1779-1784
Author(s):  
V. Mohanraj ◽  
R. Pavithra ◽  
M. Thenmozhi ◽  
R. Umarani
Keyword(s):  
Three Dimensional ◽  
Thermal Characterization ◽  
Dimensional Structure ◽  
X Ray Diffraction ◽  
Monoclinic Crystal ◽  
Evaporation Technique ◽  
Ft Ir ◽  
Thermal Stability Of ◽  
Ft Ir Spectroscopy

Phenyl trimethylammonium tetrachlorocobaltate, crystals were grown by slow evaporation technique. The crystal was bright, transparent. The three dimensional structure of the phenyl trimethylammonium tetrachlorocobaltate was obtained from single crystal X-ray diffraction studies. The molecule belongs to monoclinic crystal system with C2/c space group. The presence of functional groups and modes of vibrations were identified by FT-IR spectroscopy. 1H NMR spectroscopy was also used to characterise the compound and the thermal stability of the crystal was established by TGA/DT analysis. This work undergoes phase transition which makes the study interesting.

The Characterization of Bovine Bone-Derived Hydroxyapatite Isolated Using Novel Non-Hazardous Method

2020 ◽  
Vol 45 ◽  
pp. 49-56
Author(s):  
Aniek Setiya Budiatin ◽  
Samirah ◽  
Maria Apriliani Gani ◽  
Wenny Putri Nilamsari ◽  
Chrismawan Ardianto ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Extraction Method ◽  
Bovine Bone ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir ◽  
Novel Method ◽  
Scanning Electron

Bovine bone is a considerable source for the production of hydroxyapatite. The recent study reported a novel method to extract hydroxyapatite from bovine bone without producing hazardous residue. The bovine bones were cut and boiled in the opened chamber followed by boiling in pressurized tank. The bones were then soaked into 95% ethanol. Calcination was then conducted in 800°C, 900°C and 1,000°C, for 2 hours. The result was then grinded and sieved. The powder then was characterized using Fourier transform infrared (FT-IR), Scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD) to measure the purity of hydroxyapatite. It is concluded that the hydroxyapatite derived from this process showed 100% purity, resulting 35.34 ± 0.39% w/w from the wet bone weight and 72.3% w/w from the dried weight. The present extraction method has been proven to yield high amount of pure hydroxyapatite as well as reducing the use of hazardous reagent.

scholarly journals Growth and Characterization of Pure and Doped L-Alanine Tartrate Single Crystals

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
K. Rajesh ◽  
B. Milton Boaz ◽  
P. Praveen Kumar
Keyword(s):  
Single Crystals ◽  
Vickers Microhardness ◽  
Diffraction Method ◽  
Dielectric Studies ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cell Parameters ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

Single crystals of pure and Lanthanum doped L-Alanine Tartrate were grown by slow evaporation method. The cell parameters were determined using single crystal X-ray diffraction method. To improve the physical properties of the LAT crystal, Lanthanum dopant was added by 2 mol%. ICP studies confirm the presence of Lanthanum in the grown LAT crystal. Transparency range of the crystal was determined using UV-VIS-NIR spectrophotometer. The functional groups of pure and doped LAT crystals were analyzed by FT-IR spectroscopy. Using Vickers microhardness tester, mechanical strength of the material was found. Dielectric studies of pure and doped LAT single crystals were carried out. The doped LAT crystal is found to have efficiency higher than that of pure LAT crystal.

Synthesis and Characterization of HgSe Nanostructure Using a Novel Precursor

2013 ◽  
Vol 32 (2) ◽  
pp. 157-162 ◽  
Author(s):  
Mahdiyeh Esmaeili-Zare ◽  
Masoud Salavati-Niasari ◽  
Davood Ghanbari
Keyword(s):  
Electron Microscopy ◽  
Synthesis And Characterization ◽  
Sonochemical Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Mercury Selenide ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

AbstractMercury selenide nanostructures were synthesized from the reaction of N, N′-bis(salicylidene)propane-1,3-diamine mercury complex, (Hg(Salpn)) as a novel precursor, via sonochemical method. The effect of different surfactant on the morphology and particle size of the products was investigated. Products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy and X-ray energy dispersive spectroscopy (EDS).

scholarly journals Synthesis and Characterization of New Polyimide/Organoclay Nanocomposites Containing Benzophenone Moieties in the Main Chain

2017 ◽  
Vol 57 (2) ◽  
Author(s):  
Khalil Faghihi ◽  
Mostafa Ashouri ◽  
Akram Feyzi
Keyword(s):  
Main Chain ◽  
In Situ Polymerization ◽  
Clay Content ◽  
Nanocomposite Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

<p>A series of nanocomposites consist of organic polyimide and organo-modified clay content varying from 0 to 5 wt%, were successfully prepared by in situ polymerization. Polyimide used as a matrix of nanocomposite was prepared through the reaction of 1,4-bis [4-aminophenoxy] butane (APB) and 3،3΄،4،4΄-benzophenone tetra carboxylic dianhydride (BTDA) in N,N-dimethylacetamide (DMAc). The resulting nanocomposite films were characterized by FT-IR spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA).</p>

scholarly journals Evaluating soil quality at a landfill: a study case from morocco (tangier)

2019 ◽  
Vol 9 (4) ◽  
pp. 317-325
Author(s):  
Ikram Chaer ◽  
Asmae El Cadi ◽  
Jamal Brigui ◽  
Khadija Ziat ◽  
Mohamed Khaddor
Keyword(s):  
Heavy Metals ◽  
Organic Matter ◽  
Mineral Matter ◽  
X Ray Diffraction ◽  
Work Effort ◽  
Different Types ◽  
Ft Ir ◽  
Study Case ◽  
Ft Ir Spectroscopy

In recent decades, landfill sites have been a potential source of contamination, which can hurt the environment due to the accumulation of heavy metals and processed organic products. In the Tangier landfill, the different types of wastes are missing any prior treatment or any soil of protection. This behavior constitutes a risk factor of contamination for the soil and groundwater. Between the waste and soil, many physicochemical and biological reactions occur. The objective of this work effort is to derive a global and in-depth characterization of the organic and mineral matter of the soil samples from the Tangier landfill. The study of organic matter (OM) in soils helps to understand the evolution of soil contamination. Eight samples of soil have been studied using a range of chemical and physical analytical methods. FT-IR spectroscopy and X-ray diffraction analyses have used to investigate the nature of organic matter. The analysis of heavy metals in the soil showed that there is a significant presence of Pb, Cd, As, Cr and Zn quantities which are mainly due to industrial waste.

Synthesis and Characterization of Structure of Fe3O4@Graphene Oxide Nanocomposites

2016 ◽  
Vol 25 (6) ◽  
pp. 096369351602500 ◽  
Author(s):  
Ruimin Fu ◽  
Mingfu Zhu
Keyword(s):  
Graphene Oxide ◽  
Drug Carrier ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
Co Precipitation ◽  
Ft Ir Spectroscopy

Nowadays, the hummers method for preparation of graphene oxide (GO) was improved. The grapheme oxide @ Fe3O4 magnetic nanocomposites were synthesized by co-precipitation method. After analysing the morphology and structure of obtained nanocomposites by X-ray diffraction (XRD), transmission electron microscope (TEM) and Fourier transform infrared (FT-IR) spectroscopy, the result was shown as follows. The particle size of Fe3O4 in nanocomposites is 30 nm. Many functional groups are found in grapheme oxide, and such groups could be used to bind with the drug. In the test for magnetic properties, the nanocomposites gathered rapidly in the vicinity of the permanent magnet. The nanocomposites, with high superparamagnetism, can be used in the following applications: drug targeting transports, drug carrier, and diagnosis assistant system.

Sign in / Sign up

Export Citation Format

Share Document