The Effect of Heat Treatment on Microstructure and Mechanical Properties of ZK60 Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 718-721
Author(s):  
Ding Fei Zhang ◽  
Rong Shen Liu ◽  
Jian Peng ◽  
Wei Yuang ◽  
Hong Ju Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Age Hardening ◽  
Second Phase ◽  
Solid Solution Strengthening ◽  
Microstructure And Mechanical Properties ◽  
Long Time ◽  
Zk60 Alloy ◽  
Solution Strengthening

With different heat treatment, the microstructure and mechanical properties of ZK60 magnesium alloy were investigated. It can be concluded that heat treatment has great effect on mechanical properties of ZK60. With artificial aging after extruding, the precipitation of the second phase from the supersaturated solid solution significantly improved mechanical properties. It can greatly increase yield strength of ZK60 alloy, while the tensile strength has little change. For the combination of solid solution strengthening and age hardening, two opposite factors must be considered. On one hand, the solid solution strengthening and the later precipitation strengthening is good for alloy’s strength; on the other hand, the properties decrease as the grains grew under high temperature for a long time during solution heating.

Mechanical Properties and Microstructure of Strip Casted Ag-27%Cu-25%Zn-3%Sn Brazing Alloy

2007 ◽  
Vol 26-28 ◽  
pp. 485-488 ◽  
Author(s):  
Kee Ahn Lee ◽  
Sung Jun Kim ◽  
Moon Chul Kim
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Microstructural Analysis ◽  
Mechanical Tests ◽  
Rich Phase ◽  
Aging Heat Treatment ◽  
Solid Solution Strengthening ◽  
Solution Strengthening ◽  
Twin Roll

This work sought to examine the suitability of twin roll strip casting for Ag-27%Cu- 25%Zn-3%Sn brazing alloy (BAg-7A) and to investigate the mechanical properties and microstructure of the strip. The effect of aging heat treatment on the properties was also studied. This new manufacturing process has applications in the production of the brazing alloy. XRD and microstructural analysis of the Ag-27%Cu-25%Zn-3%Sn strip represented eutectic microstructure of a Cu-rich phase and a Ag-rich matrix regardless of heat treatment. The results of mechanical tests showed tensile strength of 470MPa, a significant enhancement; and an 18% elongation of the twin roll casted strip, due mainly to the solid solution strengthening of Zn atoms (~20%) in the Cu-rich phases. Tensile results showed gradually decreasing strengths and increasing elongation with aging heat treatment. Microstructural evolution and fractography were also investigated and related to the mechanical properties.

Effect of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of Pt-0.7Ti Microalloy

2015 ◽  
Vol 817 ◽  
pp. 645-650
Author(s):  
Qiong Zhao ◽  
Xiao Ge Zhang ◽  
Ye Fan ◽  
Guo Yi Qin ◽  
Si Yong Xu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Cold Rolling ◽  
Annealing Treatment ◽  
Recrystallization Temperature ◽  
Micro Hardness ◽  
Solid Solution Strengthening ◽  
Solution Strengthening ◽  
Rolling Deformation

The effects of cold rolling, solid solution, aging and annealing treatment on Pt-0.7Ti microalloy were investigated in this study. The microstructures of Pt-0.7Ti microalloy and the precipitated ordered phase Pt8Ti were observed and analyzed by OM, TEM, XRD. The mechanical properties of the alloy were evaluated Vicker micro-hardness. The results showed that micro amount of Ti was an effective element for solid-solution strengthening of Pt, the micro-hardness of 97% deformation for ST and ST+AG samples increased to 214HVand 224HV, respectively, which almost are double that of pure Pt. Micro-amount of long range ordered phase Pt8Ti was precipitated during the heat treatment, but the effect of order hardening in Pt-0.7Ti microalloy was not obvious. The microhardness by large rolling deformation for quenched samples almost unchanged after an annealing below 500°C for 1h, but decreased significantly at 700°C, and the recrystallization temperature was risen by 200°C than that of pure Pt.

Effect of W addition on microstructure and mechanical properties of Ni base dual two-phase intermetallic alloys

2015 ◽  
Vol 1760 ◽  
Author(s):  
Daisuke Edatsugi ◽  
Yasuyuki Kaneno ◽  
Hiroshi Numakura ◽  
Takayuki Takasugi
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Base Alloy ◽  
Intermetallic Alloys ◽  
Two Phase ◽  
Solid Solution Strengthening ◽  
Microstructure And Mechanical Properties ◽  
Heat Treated ◽  
Phase Intermetallic ◽  
Solution Strengthening

ABSTRACTThe effect of W addition on microstructure and mechanical properties of Ni3Al (L12) and Ni3V (D022) two-phase intermetallic alloys has been investigated. W was added to the base alloy composition, Ni75Al10V12Nb3 (at. %) in place of either Ni, Al or V. The W-added alloy ingots were heat-treated in vacuum at 1575 K for 5 h. The majority of W-added alloys showed a dual two-phase microstructures while the alloy in which 3 at. % W substituted for Ni exhibited the dual two-phase microstructure containing W solid solution dispersions. Vickers hardness was significantly enhanced by W addition, which is primarily due to solid-solution strengthening.

Influence of Heat Treatment on Microstructure and Mechanical Properties of Die-Cast AZ91D Alloy with RE Elements

2014 ◽  
Vol 633-634 ◽  
pp. 98-102 ◽  
Author(s):  
Jia Wei Yuan ◽  
Xing Gang Li ◽  
Kui Zhang ◽  
Ting Li ◽  
Yong Jun Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Az91d Alloy ◽  
Phase Precipitation ◽  
Solid Solution Strengthening ◽  
Microstructure And Mechanical Properties ◽  
Die Cast ◽  
Solution Strengthening ◽  
Re Elements

The effect of online solution and subsequent age heat treatment on microstructure and mechanical properties of die-cast AZ91D +1wt. %RE alloy were researched. The results indicated that online solution heat treatment led to inhibit some β-Mg17Al12 phase precipitation, and remained the Al element in matrix plays a role of solid solution strengthening. The online solution samples were aged at 160°C, 180°Cand 200°C. Microstructure results suggested that age treatment caused some lamellar β-Mg17Al12 phases precipitated near grain boundaries. The tensile properties of samples under air cool, online solution and subsequent age heat treatment were tested, which UTS were 194 MPa, 243 MPa and 244 MPa, and the elongation were 3.67%, 3.97% and 1.6%, respectively. The results indicated that the online solution could enhance the mechanical properties significantly, which the subsequent age heat treatment could not improve.

Microstructure and Mechanical Properties of Backward-Extruded Mg-Zn-xCa Biomaterials

2013 ◽  
Vol 747-748 ◽  
pp. 426-430
Author(s):  
Xue Jun Li ◽  
Hui Li ◽  
Shuang Shuang Zhao ◽  
Ning Ma ◽  
Qiu Ming Peng
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Solid Solution Strengthening ◽  
Backward Extrusion ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Microstructure And Mechanical Properties ◽  
Solution Strengthening ◽  
Extrusion Technology ◽  
Precipitate Strengthening

The Mg-1.0Zn-xCa (x=0.2, 0.5, 0.8, 1 wt. %) alloys were prepared by zone solidification and backward extrusion technology. The microstructure and mechanical properties of backward-extruded Mg-1.0Zn-xCa alloys were investigated. The results showed that these backward-extruded Mg-1.0Zn-xCa alloys were mainly composed of equi-axed pentagon-shaped grains and some Mg0.9Zn0.03 precipitates. The tensile and compressive strengths of backward-extruded Mg-1.0Zn-xCa alloys were greatly improved. The improved mechanical properties are mostly attributed to fine grain strengthening, solid solution strengthening and precipitate strengthening. The results demonstrated that the micro alloying of Ca element was one of effective method to improve the mechanical properties of Mg-1.0Zn based biomaterials.

Effect of Ti Element on Microstructure and Properties of Cu-Cr Alloy

2015 ◽  
Vol 817 ◽  
pp. 307-311 ◽  
Author(s):  
Peng Chao Zhang ◽  
Jin Chuan Jie ◽  
Yuan Gao ◽  
Tong Min Wang ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Spherical Shape ◽  
Precipitation Strengthening ◽  
Peak Hardness ◽  
Ti Alloy ◽  
Strengthening Mechanisms ◽  
Vacuum Melting ◽  
Solid Solution Strengthening ◽  
Solution Strengthening

The Cu-Cr and Cu-Cr-Ti alloy plates were prepared by vacuum melting and plastic deformation. The effect of slight Ti element on microstructure and mechanical properties of Cu-Cr alloy was discussed. The result shows that Cr particles with spherical shape precipitated from Cu matrix after aging. Plenty Ti atoms dissolved in the vicinity of Cr particles and there were still parts of solid solution Ti atoms in other regions. Improvements in peak hardness and softening resistance were achieved with the addition of Ti element in Cu-Cr alloy. The addition of 0.1 wt.% Ti element makes Cu-Cr alloy possess tensile strength of 565 MPa and hardness of 185.9 HV after aging at 450 °C for 120 min, which can be attributed to multiple strengthening mechanisms, i.e. work hardening, solid solution strengthening and precipitation strengthening.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

Sign in / Sign up

Export Citation Format

Share Document