Preparation and Electrical Property of Calcia Stabilized Zirconia Ceramics

2014 ◽  
Vol 616 ◽  
pp. 157-165 ◽  
Author(s):  
Chang Lian Chen ◽  
Hong Quan Wang ◽  
Jia You Ji ◽  
Ma Ya Luo ◽  
Bo Wu ◽  
...  
Keyword(s):  
Grain Size ◽  
Electrical Property ◽  
Arrhenius Equation ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Cubic Phase ◽  
Pressureless Sintering ◽  
Stabilized Zirconia ◽  
Zirconia Ceramics ◽  
Sintering Method

In this paper, using ZrO2 and Ca (NO3)•4H2O as raw materials, we prepared a series of calica stabilized zirconia (CSZ) ceramics by pressureless sintering method. The results show that the relative densities of all sintered samples are above 90%, and the sintered samples are composed of cubic, tetragonal and monoclinic ZrO2, and the main phase is cubic ZrO2 and tetragonal ZrO2. The content of cubic phase increases with the increase of sintering temperature and adding CaO content. The grain size of the sintered samples is relatively uniform and some pores exist. Increasing the additive amount of CaO, the conductivity first rises and then decreases, and the conductivity value of the sample containing 5wt% CaO is the maximum. When the sintering temperature is up to 1600 oC, the conductivity of the sample containing 5wt% CaO is up to 0.016S•cm-1 at 800 oC. Furthermore, the conductivity of sintered samples is increasing with the increase of test temperature according to the Arrhenius equation.

Effects of Sintering Temperature on Structure and Electronic Properties of Mg0.2Zn0.8O:Al Ceramics

2011 ◽  
Vol 320 ◽  
pp. 236-239
Author(s):  
Hong Yan ◽  
Hua Wang ◽  
Shang Ju Zhou
Keyword(s):  
Grain Size ◽  
Electronic Properties ◽  
Sintering Temperature ◽  
Raw Materials ◽  
High Density ◽  
Homogeneous Structure ◽  
Second Phase ◽  
Pressureless Sintering ◽  
Nano Scale ◽  
Phase Nucleation

Mg0.2Zn0.8O:Al ceramics with high density using nano scale ZnO, MgO and Al2O3 powders as raw materials were obtained by pressureless sintering. The influence of presintering powder and sintering temperature on microstructure of Mg0.2Zn0.8O:Al ceramics were studied. The experiment indicated that presintering powder might decrease produce of the second phase nucleation. The grain size became gradually larger and density of ceramic became obviously higher from 1100°C to 1300°C, but the rising-trend became slower after 1300°C. The Mg0.2Zn0.8O:Al ceramics with high density and homogeneous structure can be made at 1300°C for

scholarly journals Effect of starting materials and sintering temperature on microstructure and optical properties of Y2O3:Yb3+ 5 at% transparent ceramics

2020 ◽  
Author(s):  
R. P. Yavetskiy ◽  
A. E. Balabanov ◽  
S. V. Parkhomenko ◽  
O. S. Kryzhanovska ◽  
A. G. Doroshenko ◽  
...  
Keyword(s):  
Grain Size ◽  
Optical Properties ◽  
Sintering Temperature ◽  
Raw Materials ◽  
High Energy ◽  
Reactive Sintering ◽  
Average Grain Size ◽  
Median Particle ◽  
Energy Ball ◽  
Sintering Method

Abstract Y2O3:Yb3+ 5 at% ceramics have been synthesized by the reactive sintering method using different commercial yttria powders (Alfa-Micro, Alfa-Nano, and ITO-V) as raw materials. It has been shown that all Y2O3 starting powders consist from agglomerates up to 5–7 µm in size which are formed from 25–60 nm primary particles. High-energy ball milling allows to significantly decreasing the median particle size D50 below 500 nm regardless of the commercial powders used. Sintering experiments indicate that powder mixtures fabricated from Alfa-Nano yttria powders have the highest sintering activity, while (Y0.86La0.09Yb0.05)2O3 ceramics sintered at 1750 °C for 10 h are characterized by the highest transmittance of about 45%. Y2O3:Yb3+ ceramics have been obtained by the reactive sintering at 1750–1825°C using Alfa-Nano Y2O3 powders and La2O3+ZrO2 as a complex sintering aid. The effects of the sintering temperature on densification processes, microstructure, and optical properties of Y2O3:Yb3+ 5 at% ceramics have been studied. It has been shown that Zr4+ ions decrease the grain growth of Y2O3:Yb3+ ceramics for sintering temperatures 1750–1775 °C. Further increasing the sintering temperature was accompanied by a sharp increase of the average grain size of ceramics referred to changes of structure and chemical composition of grain boundaries, as well as their mobility. It has been determined that the optimal sintering temperature to produce high-dense yttria ceramics with transmittance of 79%–83% and average grain size of 8 µm is 1800 °C. Finally, laser emission at ∼1030.7 nm with a slope efficiency of 10% was obtained with the most transparent Y2O3:Yb3+ 5 at% ceramics sintered.

scholarly journals Pressureless Sintering of YIG Ceramics from Coprecipitated Nanopowders

2021 ◽  
Vol 7 (5) ◽  
pp. 56
Author(s):  
Yimin Yang ◽  
Xiaoying Li ◽  
Ziyu Liu ◽  
Dianjun Hu ◽  
Xin Liu ◽  
...  
Keyword(s):  
High Temperature ◽  
Calcination Temperature ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Secondary Phase ◽  
Coprecipitation Method ◽  
Pressureless Sintering ◽  
Densification Behavior ◽  
Sintering Process

Nanoparticles prepared by the coprecipitation method were used as raw materials to fabricate Y3Fe5O12 (YIG) ceramics by air pressureless sintering. The synthesized YIG precursor was calcinated at 900–1100 °C for 4 h in air. The influences of the calcination temperature on the phase and morphology of the nanopowders were investigated in detail. The powders calcined at 1000–1100 °C retained the pure YIG phase. YIG ceramics were fabricated by sintering at 1200–1400 °C for 10 h, and its densification behavior was studied. YIG ceramics prepared by air sintering at 1250 °C from powders calcinated at 1000 °C have the highest in-line transmittance in the range of 1000-3000 nm. When the sintering temperature exceeds 1300 °C, the secondary phase appears in the YIG ceramics, which may be due to the loss of oxygen during the high-temperature sintering process, resulting in the conversion of Fe3+ into Fe2+.

scholarly journals Effect of Sintering Temperature on Microstructure and Mechanical Properties of Hot-Pressed Fe/FeAl2O4 Composite

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Kuai Zhang ◽  
Yungang Li ◽  
Hongyan Yan ◽  
Chuang Wang ◽  
Hui Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Hot Press ◽  
Microstructure And Mechanical Properties ◽  
Powder Particles ◽  
Hot Press Sintering ◽  
Sintering Method

An Fe/FeAl2O4 composite was prepared with Fe-Fe2O3-Al2O3 powder by a hot press sintering method. The mass ratio was 6:1:2, sintering pressure was 30 MPa, and holding time was 120 min. The raw materials for the powder particles were respectively 1 µm (Fe), 0.5 µm (Fe2O3), and 1 µm (Al2O3) in diameter. The effect of sintering temperature on the microstructure and mechanical properties of Fe/FeAl2O4 composite was studied. The results showed that Fe/FeAl2O4 composite was formed by in situ reaction at 1300 °C–1500 °C. With the increased sintering temperature, the microstructure and mechanical properties of the Fe/FeAl2O4 composite showed a change law that initially became better and then became worse. The best microstructure and optimal mechanical properties were obtained at 1400 °C. At this temperature, the grain size of Fe and FeAl2O4 phases in Fe/FeAl2O4 composite was uniform, the relative density was 96.7%, and the Vickers hardness and bending strength were 1.88 GPa and 280.0 MPa, respectively. The wettability between Fe and FeAl2O4 was enhanced with increased sintering temperature. And then the densification process was accelerated. Finally, the microstructure and mechanical properties of the Fe/FeAl2O4 composite were improved.

Preparation and Microstructure of Pressureless Sintered Si2ON2-SiC Ceramic

2011 ◽  
Vol 335-336 ◽  
pp. 699-703
Author(s):  
Hui Hui Tan ◽  
Zhu Xing Tang ◽  
Xia Zhao ◽  
He Zhang
Keyword(s):  
Bulk Density ◽  
Sintering Temperature ◽  
Pressureless Sintering ◽  
Nitriding Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Effect Of Additives ◽  
Sic Ceramic ◽  
Sintering Method ◽  
Scanning Electron

This paper introduces Si2ON2-SiC ceramic fabricated by pressureless sintering method and studies the effect of additives, nitriding temperatures on bulk density, porosity, phase composition and microstructure. It is discovered that additives MgO, CeO2 can increase the densities of Si2ON2-SiC ceramic apparently, and MgO additive has a better effect than CeO2. Nitriding temperature also is an important factor. The bulk density of the specimen with MgO additive reaches maximum at 1.91 g/cm3 when sintered at 1450 °C, and the bulk density of specimen with CeO2 additive is 1.86 g/cm3 at the same condition while the bulk density of the specimen without additive is only 1.75 g/cSuperscript textm3. The X-ray diffraction and scanning electron microscopy of the specimens show that the amount of Si2ON2 increase with the sintering temperature increase. But when the temperature is higher than 1500 °C the Si2ON2 grains will decompose into Si3N4, and Si2ON2 will vanish at 1550 °C

Preparation and Investigation on Properties of the MgTiO3-CaTiO3 Microwave Ceramic Materials

2014 ◽  
Vol 997 ◽  
pp. 419-423 ◽  
Author(s):  
Li Dong ◽  
Gui Xia Dong ◽  
Yuan Yuan Li ◽  
Xi Zhang
Keyword(s):  
Dielectric Constant ◽  
Sintering Temperature ◽  
Ceramic Materials ◽  
Volume Density ◽  
Second Phase ◽  
Pressureless Sintering ◽  
Solid Reaction ◽  
Reaction Method ◽  
Microwave Ceramic ◽  
Sintering Method

The MgTiO3 and CaTiO3 powders were synthesized by solid reaction method, and MgTiO3-CaTiO3 ceramic was prepared using pressureless sintering method. The experiment prepared MgTiO3-CaTiO3 ceramics with high compactness and stable permittivity by the way of changing the mole ratio of MgTiO3 and CaTiO3 to investigate the effect of CaTiO3 on the performances of MgTiO3-CaTiO3 ceramics. The results show that Mg2TiO4 formed as second phase during sintering. Volume density and dielectric constant of MgTiO3-CaTiO3 ceramics with 10%mol CaTiO3 reach maximum of 3.612g/cm3 and 17.8, respectively, under 1460°C sintering temperature. And for the MgTiO3-CaTiO3 ceramics with 5%mol CaTiO3 the maximum values which are 3.5g/cm3 and 16.6, respectively, appear under 1510°C sintering temperature.

Preparation of the System of BaO-MgO-Al2O3-TiO2 Acid-Resistant Fracturing Proppants

2011 ◽  
Vol 399-401 ◽  
pp. 855-859
Author(s):  
Ting Ting Wu ◽  
Bo Lin Wu
Keyword(s):  
Sintering Temperature ◽  
Raw Materials ◽  
Acid Resistance ◽  
Pressureless Sintering ◽  
Alumina Matrix ◽  
X Ray Diffraction ◽  
X Ray ◽  
Acid Solubility ◽  
Resistance Performance ◽  
Scanning Electron

In order to improve the acid resistance and reduce the apparent density of fracturing proppants, TiO2 powder added in the system of BaO-MgO-Al2O3 fracturing proppants were prepared by the technique of pressureless sintering. The properties of the samples were investigated by the measurements of acid solubility, X-ray diffraction and scanning electron microscopy. The results show that the acid solubility of alumina matrix fracturing proppants contenting TiO2 of the 4wt% and BaO/MgO with the ratio of 3:7 is 0.15%. It is an important development in acid resistance performance of fracturing proppants research on laboratory. TiO2 is added to the raw materials and then calcine them to ceramics, which can reduces the sintering temperature, promote the densification and improve acid-resistant property of fracturing proppants.

Effect of Sintering Temperature on Properties of YAG Porous Ceramics via Atmospheric Sintering Method

2018 ◽  
Vol 281 ◽  
pp. 224-229 ◽  
Author(s):  
Fang Wang ◽  
Ming Han Xu ◽  
Ai Xia Chen ◽  
Long Tao Liu ◽  
Zhi Hui Li ◽  
...  
Keyword(s):  
Sintering Temperature ◽  
Raw Materials ◽  
Porous Ceramics ◽  
Soluble Starch ◽  
Product Performance ◽  
Effect Of Temperature ◽  
Sintering Process ◽  
Molding Process ◽  
Sintering Aid ◽  
Sintering Method

YAG materials have a number of unique properties, the application is very extensive, the burn is due to the temperature is too high or the residence time at high temperatures is caused. The undercurrent is the sintering temperature is too low or the holding time is not enough, resulting in product performance is too low or too small shrinkage. In this paper, the effect of sintering temperature on properties of YAG porous ceramics was investigated. The results showed that the firing temperature of the ingredients will be different and cause the same sintering process and sintering additives content of different samples burned. The increase in the content of SiO2 in the furnish with the sintering aid tends to occur. the effect of temperature on the mechanical properties of the samples after sintering was significant, so the raw materials include 60wt%YAG, 10wt% CaO, 10wt% SiO2 and 20wt% soluble starch, the molding process in 20MPa pressure 10min, the sintering at 1500°C for 2h, the sample porosity is 42.2%, the compressive strength is 5.8MPa, the outside shape is keep intact and the better pore microstructure is shown.

Preparation and Characterization of (1-x)BiScO3-xPbTiO3 Ceramics by Two-Step Sintering

2008 ◽  
Vol 368-372 ◽  
pp. 8-10 ◽  
Author(s):  
Ting Ting Zou ◽  
Xiao Hui Wang ◽  
Long Tu Li
Keyword(s):  
Grain Size ◽  
Low Temperature ◽  
High Performance ◽  
Piezoelectric Properties ◽  
Sintering Temperature ◽  
Sintering Aid ◽  
Potential Approach ◽  
Fine Grain ◽  
Sintering Method

High-performance fine-grain (1-x)BiScO3-xPbTiO3 ceramics were prepared by two-step sintering method. Influences of sintering temperature, holding time, and composition on the microstructure and properties were discussed. The BSPT ceramics obtained via two-step sintering reaches density higher than 95% at a low temperature of 800°C without any sintering aid, and the grain size of the ceramics is also effectively controlled. Excellent piezoelectric properties between the composition of x=0.63 and x=0.64 reveals a probable MPB in this range, suggesting a potential approach to pursue high performance BSPT ceramics.

Sign in / Sign up

Export Citation Format

Share Document