Effect of Sintering Temperature on Properties of YAG Porous Ceramics via Atmospheric Sintering Method

2018 ◽  
Vol 281 ◽  
pp. 224-229 ◽  
Author(s):  
Fang Wang ◽  
Ming Han Xu ◽  
Ai Xia Chen ◽  
Long Tao Liu ◽  
Zhi Hui Li ◽  
...  
Keyword(s):  
Sintering Temperature ◽  
Raw Materials ◽  
Porous Ceramics ◽  
Soluble Starch ◽  
Product Performance ◽  
Effect Of Temperature ◽  
Sintering Process ◽  
Molding Process ◽  
Sintering Aid ◽  
Sintering Method

YAG materials have a number of unique properties, the application is very extensive, the burn is due to the temperature is too high or the residence time at high temperatures is caused. The undercurrent is the sintering temperature is too low or the holding time is not enough, resulting in product performance is too low or too small shrinkage. In this paper, the effect of sintering temperature on properties of YAG porous ceramics was investigated. The results showed that the firing temperature of the ingredients will be different and cause the same sintering process and sintering additives content of different samples burned. The increase in the content of SiO2 in the furnish with the sintering aid tends to occur. the effect of temperature on the mechanical properties of the samples after sintering was significant, so the raw materials include 60wt%YAG, 10wt% CaO, 10wt% SiO2 and 20wt% soluble starch, the molding process in 20MPa pressure 10min, the sintering at 1500°C for 2h, the sample porosity is 42.2%, the compressive strength is 5.8MPa, the outside shape is keep intact and the better pore microstructure is shown.

scholarly journals Pressureless Sintering of YIG Ceramics from Coprecipitated Nanopowders

2021 ◽  
Vol 7 (5) ◽  
pp. 56
Author(s):  
Yimin Yang ◽  
Xiaoying Li ◽  
Ziyu Liu ◽  
Dianjun Hu ◽  
Xin Liu ◽  
...  
Keyword(s):  
High Temperature ◽  
Calcination Temperature ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Secondary Phase ◽  
Coprecipitation Method ◽  
Pressureless Sintering ◽  
Densification Behavior ◽  
Sintering Process

Nanoparticles prepared by the coprecipitation method were used as raw materials to fabricate Y3Fe5O12 (YIG) ceramics by air pressureless sintering. The synthesized YIG precursor was calcinated at 900–1100 °C for 4 h in air. The influences of the calcination temperature on the phase and morphology of the nanopowders were investigated in detail. The powders calcined at 1000–1100 °C retained the pure YIG phase. YIG ceramics were fabricated by sintering at 1200–1400 °C for 10 h, and its densification behavior was studied. YIG ceramics prepared by air sintering at 1250 °C from powders calcinated at 1000 °C have the highest in-line transmittance in the range of 1000-3000 nm. When the sintering temperature exceeds 1300 °C, the secondary phase appears in the YIG ceramics, which may be due to the loss of oxygen during the high-temperature sintering process, resulting in the conversion of Fe3+ into Fe2+.

scholarly journals Effect of Sintering Temperature on Microstructure and Mechanical Properties of Hot-Pressed Fe/FeAl2O4 Composite

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Kuai Zhang ◽  
Yungang Li ◽  
Hongyan Yan ◽  
Chuang Wang ◽  
Hui Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Hot Press ◽  
Microstructure And Mechanical Properties ◽  
Powder Particles ◽  
Hot Press Sintering ◽  
Sintering Method

An Fe/FeAl2O4 composite was prepared with Fe-Fe2O3-Al2O3 powder by a hot press sintering method. The mass ratio was 6:1:2, sintering pressure was 30 MPa, and holding time was 120 min. The raw materials for the powder particles were respectively 1 µm (Fe), 0.5 µm (Fe2O3), and 1 µm (Al2O3) in diameter. The effect of sintering temperature on the microstructure and mechanical properties of Fe/FeAl2O4 composite was studied. The results showed that Fe/FeAl2O4 composite was formed by in situ reaction at 1300 °C–1500 °C. With the increased sintering temperature, the microstructure and mechanical properties of the Fe/FeAl2O4 composite showed a change law that initially became better and then became worse. The best microstructure and optimal mechanical properties were obtained at 1400 °C. At this temperature, the grain size of Fe and FeAl2O4 phases in Fe/FeAl2O4 composite was uniform, the relative density was 96.7%, and the Vickers hardness and bending strength were 1.88 GPa and 280.0 MPa, respectively. The wettability between Fe and FeAl2O4 was enhanced with increased sintering temperature. And then the densification process was accelerated. Finally, the microstructure and mechanical properties of the Fe/FeAl2O4 composite were improved.

Preparation and Electrical Property of Calcia Stabilized Zirconia Ceramics

2014 ◽  
Vol 616 ◽  
pp. 157-165 ◽  
Author(s):  
Chang Lian Chen ◽  
Hong Quan Wang ◽  
Jia You Ji ◽  
Ma Ya Luo ◽  
Bo Wu ◽  
...  
Keyword(s):  
Grain Size ◽  
Electrical Property ◽  
Arrhenius Equation ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Cubic Phase ◽  
Pressureless Sintering ◽  
Stabilized Zirconia ◽  
Zirconia Ceramics ◽  
Sintering Method

In this paper, using ZrO2 and Ca (NO3)•4H2O as raw materials, we prepared a series of calica stabilized zirconia (CSZ) ceramics by pressureless sintering method. The results show that the relative densities of all sintered samples are above 90%, and the sintered samples are composed of cubic, tetragonal and monoclinic ZrO2, and the main phase is cubic ZrO2 and tetragonal ZrO2. The content of cubic phase increases with the increase of sintering temperature and adding CaO content. The grain size of the sintered samples is relatively uniform and some pores exist. Increasing the additive amount of CaO, the conductivity first rises and then decreases, and the conductivity value of the sample containing 5wt% CaO is the maximum. When the sintering temperature is up to 1600 oC, the conductivity of the sample containing 5wt% CaO is up to 0.016S•cm-1 at 800 oC. Furthermore, the conductivity of sintered samples is increasing with the increase of test temperature according to the Arrhenius equation.

Microstructure, Mechanical Properties, and Electrical Resistivities of Mica Glass-Ceramics with Flake Phlogopite and Waste Glass

2014 ◽  
Vol 602-603 ◽  
pp. 640-643
Author(s):  
Yu Fei Chen ◽  
Yan Gai Liu ◽  
Xiao Wen Wu ◽  
Zhao Hui Huang ◽  
Ming Hao Fang
Keyword(s):  
High Speed ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Glass Ceramics ◽  
Waste Glass ◽  
Raw Material ◽  
Bending Test ◽  
Electric Locomotive ◽  
Molding Process ◽  
Electrical Resistivities

Mica glass-ceramics can be applied in all kinds of electrical equipment, locomotive internal circuits in high-speed rail, ordinary electric locomotive and subway locomotive. In this study, mica glass-ceramics were prepared by sintering process using flake mica and waste glass as the main raw material with low cost. Different mica glass-ceramic samples were fabricated by changing the formula of raw materials, molding process and sintering temperature. X-ray diffraction, scanning electron microscopy, three-point bending test, and balanced-bridge technique were applied to investigate the phase, microstructure, mechanical and electrical resistivities of the samples, respectively. The results show that the optimum sintering temperature is 900 to 1000 °C holding for two hours, the desirable ratio is 70 wt% of mica powder while 30 wt% of glass powder. In that condition the sample could be less porosity, high flexural strength (63.3 MPa) and eligible electrical resistivity (0.4×1013 Ω·cm).

Preparation of Porous Wollastonite Ceramics for Filtration

2007 ◽  
Vol 336-338 ◽  
pp. 1102-1104 ◽  
Author(s):  
Ming Sheng He ◽  
Jian Bao Li ◽  
Bo Wen Li ◽  
Hong Lin ◽  
Xiao Zhan Yang ◽  
...  
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sintering Temperature ◽  
Porous Ceramics ◽  
Holding Time ◽  
Starting Material ◽  
Sintering Method

Wollastonite powder was selected as a starting material with carbonate as pore-forming agent and binder added. The porous ceramics were prepared at different temperature by sintering method. The process includes batching, granulating, pressing molding, drying and sintering. It is discussed the influence of sintering temperature, dosage of binder, dosage of pore-forming agent, pressure of molding and holding time on the performance of porous ceramics. According to the principle of particles stack, the porous wollastonite ceramics for filtration with various diameters, shapes and porosity were fabricated by serial experiments. These products have 1 to 10 microns in pore size, 30.04 to 66.15% in porosity, 2.82 m2/g in specific surface area.

Barium Strontium Titanate Ceramics Prepared by a Reaction-Sintering Process

2004 ◽  
Vol 848 ◽  
Author(s):  
Yi-Cheng Liou ◽  
Jen-Hsien Chen ◽  
Chi-Ting Wu
Keyword(s):  
Strontium Titanate ◽  
Barium Strontium Titanate ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Reaction Sintering ◽  
Sintering Process ◽  
Barium Strontium ◽  
Bst Ceramics ◽  
Titanate Ceramics

ABSTRACTBarium strontium titanate (Ba0.7Sr0.3TiO3, BST) ceramics prepared by a reaction-sintering process were investigated. The mixture of raw materials of stoichiometric Ba0.7Sr0.3TiO3 was pressed and sintered into ceramics without any calcination stage involved. Perovskite BST ceramics were obtained after sintered at 1330–1370°C for 2–6 h. For 6 h soak time, a density value 5.68g/cm3 (99.8% of the theoretic value) was obtained at 1350°C sintering. Grains of sizes between 2μm and 15μm were formed after 1330–1370°C sintering for 2–6 h. A diffused ferroelectric-paraelectric transition was observed in pellets sintered at 1330°C for 2 h and disappeared at a longer soak time or a higher sintering temperature.

Preparation of Porous ZrO2-Al2O3 Composite Ceramic with High Strength and Good Corrosion-Resistance

2011 ◽  
Vol 197-198 ◽  
pp. 1545-1548 ◽  
Author(s):  
Qi Bing Chang ◽  
Xing Qin Liu ◽  
Xia Wang ◽  
Yong Qing Wang ◽  
Jian Er Zhou
Keyword(s):  
Corrosion Resistance ◽  
Bending Strength ◽  
Sintering Temperature ◽  
High Strength ◽  
Composite Ceramic ◽  
Ceramic Membranes ◽  
Porous Ceramics ◽  
Sintering Aid ◽  
Filtration Membrane ◽  
Before And After

In order to develop porous ceramics with high strength and corrosion resistance as the support for the preparation of asymmetric ceramic membranes, porous ZrO2-Al2O3 composite is designed and fabricated by adding Zr(OH)4.as sintering aid. The content of Zr(OH)4, the sintering temperature and the bending strength before and after corrosion of the composite are discussed. The results shows that 10wt% ZrO2-10wt% Zr(OH)4 -80wt%Al2O3 composite bar fabricated by cold press with the porosity of 32% can be fabricated in 1550°C for 4 h. The bending strength of the composite is 111.2MPa. After corrosion, the quality lose and the bending strength lose is no more than 1%. The tubular composite is suit for the preparation of micro-filtration membrane.

Preparation and characterization of low-cost high-performance mullite-quartz ceramic proppants for coal bed methane wells

2018 ◽  
Vol 25 (5) ◽  
pp. 957-961 ◽  
Author(s):  
Kaiyue Wang ◽  
Huijun Wang ◽  
Yi Zhou ◽  
Guomin Li ◽  
Yaqiao Wu ◽  
...  
Keyword(s):  
High Performance ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Low Cost ◽  
Quartz Ceramic ◽  
Coal Bed ◽  
Coal Bed Methane ◽  
Sintering Process ◽  
Flow Mechanism

AbstractIn this study, the mullite-quartz-based proppants were successfully prepared by using the coal gangue as the raw materials. Then, the effects of the additive and the sintering temperature on the composition, microstructure, and properties of the proppants were investigated. Results showed that the proppants sintered at 1250°C with the 10 wt% bauxite additive presented the best performance, which was very close to that of the quartz-proppant, and met the operational requirements of the 52 MPa coal bed methane wells. The viscous flow mechanism of the liquid phase formed during the sintering process also promoted the arrangement of the grains, thus benefiting the densification and the strength of the proppants.

Preparation and Characterization of (1-x)BiScO3-xPbTiO3 Ceramics by Two-Step Sintering

2008 ◽  
Vol 368-372 ◽  
pp. 8-10 ◽  
Author(s):  
Ting Ting Zou ◽  
Xiao Hui Wang ◽  
Long Tu Li
Keyword(s):  
Grain Size ◽  
Low Temperature ◽  
High Performance ◽  
Piezoelectric Properties ◽  
Sintering Temperature ◽  
Sintering Aid ◽  
Potential Approach ◽  
Fine Grain ◽  
Sintering Method

High-performance fine-grain (1-x)BiScO3-xPbTiO3 ceramics were prepared by two-step sintering method. Influences of sintering temperature, holding time, and composition on the microstructure and properties were discussed. The BSPT ceramics obtained via two-step sintering reaches density higher than 95% at a low temperature of 800°C without any sintering aid, and the grain size of the ceramics is also effectively controlled. Excellent piezoelectric properties between the composition of x=0.63 and x=0.64 reveals a probable MPB in this range, suggesting a potential approach to pursue high performance BSPT ceramics.

scholarly journals Effects of oxidation of SiC aggregates on the sintering behaviour and microstructures of SiC-CaAl12O19 composite refractories

2021 ◽  
Vol 15 (1) ◽  
pp. 11-18
Author(s):  
Yaochen Si ◽  
Miao Xia ◽  
Hongxia Li ◽  
Honggang Sun ◽  
Ang Guo ◽  
...  
Keyword(s):  
Firing Temperature ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Coal Slurry ◽  
Refractory Materials ◽  
Sintering Process ◽  
Active Oxidation ◽  
Passive Oxidation ◽  
Different Temperatures ◽  
Sintering Behaviour

In order to develop chrome-free refractory materials applicable in coal slurry gasification, SiC-CaAl12O19 (SiC-CA6) composite refractories were developed and prepared by using SiC aggregates and CA6 powders as main raw materials. The sintering behaviour of the composites was investigated. After firing at different temperatures under CO atmosphere, the effects of oxidation of SiC aggregates on the sintering behaviour and microstructures of SiC-CA6 composite refractorieswere investigated. SiC-CA6 composites could not be sintered when firing temperature was lower than 1500?C. SiC had a passive oxidation and the oxidation components were able to react with CA6 to form CaAl2Si2O8. The CaAl2Si2O8 melted into liquid when sintering temperature was in the range of 1500-1600?C, which promoted the sintering process of the SiC-CA6 composites. At temperatures above 1600 ?C, an active oxidation of SiC occurred. Simultaneously, SiC could also reacted with the SiO2(s,l) to form SiO, leading to the precipitation of Al2O3 and CaO in the liquid to generate plate-like CA6. Above this temperature, the sintering of the SiC-CA6 composite refractories was affected by the growth of CA6 and oxidation of SiC. This work demonstrates that the optimal sintering temperature for the SiC-CA6 composite refractories was 1600?C.

Sign in / Sign up

Export Citation Format

Share Document