Influence of Process Conditions on the Local Shrinkage and on the Pressure Evolution inside the Mold Cavity of the Injection Molded Polypropylene in Two Modifications - PP Homopolymer; 40 % Talc Filled PP

2015 ◽  
Vol 669 ◽  
pp. 11-18
Author(s):  
Robert Záboj
Keyword(s):  
Rectangular Plate ◽  
Wall Thickness ◽  
Injection Rate ◽  
Semicrystalline Polymer ◽  
Mutual Interaction ◽  
Mold Cavity ◽  
Process Conditions ◽  
Melt Temperature ◽  
Injection Molded ◽  
Pressure Evolution

This work is focusing on optimization of the chosen process conditions (melt temperature, injection rate and holding pressure) and their mutual interaction on the local shrinkage of wall thickness carried out on rectangular plate. The test was applied on semicrystalline polymer in following modifications - polypropylene homopolymer and 40 % talc filled polypropylene. For better understanding of processes influencing shrinkage the pressure evolution inside cavity was captured by transducers placed near the gate and at the end of flow.

scholarly journals Characterization of Microchannel Replicability of Injection Molded Electrophoresis Microfluidic Chips

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 608 ◽  
Author(s):  
Bingyan Jiang ◽  
Laiyu Zhu ◽  
Liping Min ◽  
Xianglin Li ◽  
Zhanyu Zhai ◽  
...  
Keyword(s):  
Microfluidic Chip ◽  
Mold Temperature ◽  
Disease Diagnosis ◽  
Injection Rate ◽  
Holding Time ◽  
Critical Element ◽  
Profile Curve ◽  
Microfluidic Chips ◽  
Melt Temperature ◽  
Injection Molded

Microfluidic chips have been widely applied in biochemical analysis, DNA sequencing, and disease diagnosis due to their advantages of miniaturization, low consumption, rapid analysis, and automation. Injection molded microfluidic chips have attracted great attention because of their short processing time, low cost, and mass production. The microchannel is the critical element of a microfluidic chip, and thus the microchannel replicability directly affects the performance of the microfluidic chip. In the current paper, a new method is proposed to evaluate the replicability of the microchannel profile via the root mean square value of the actual profile curve and the ideal profile curve of the microchannel. To investigate the effects of injection molding parameters (i.e., mold temperature, melting temperature, holding pressure, holding time, and injection rate) on microchannel replicability, a series of single-factor experiments were carried out. The results showed that, within the investigated experimental range, the increase of mold temperature, melt temperature, holding pressure, holding time, and injection rate could improve microchannel replicability accuracy. Specifically, the microchannels along the flow direction of the polymer melt were significantly affected by the mold temperature and melt temperature. Moreover, the replicability of the microchannel was influenced by the distance from the injection gate. The effect of microchannel replication on electrophoresis was demonstrated by a protein electrophoresis experiment.

scholarly journals Experimental and Numerical Investigation of the Effect of Process Conditions on Residual Wall Thickness and Cooling and Surface Characteristics of Water-Assisted Injection Molded Hollow Products

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Hyungpil Park ◽  
Baeg-Soon Cha ◽  
Byungohk Rhee
Keyword(s):  
Injection Molding ◽  
Wall Thickness ◽  
Automobile Industry ◽  
Three Dimensional ◽  
Surface Characteristics ◽  
Process Conditions ◽  
Melt Temperature ◽  
Hollow Section ◽  
Injection Process ◽  
Tube Type

Recently, water-assisted injection molding was employed in the automobile industry to manufacture three-dimensional hollow tube-type products with functionalities. However, process optimization is difficult in the case of water-assisted injection molding because of the various rheological interactions between the injected water and the polymer. In this study, the boiling phenomenon that occurs because of the high melt temperature when injecting water and the molding characteristics of the hollow section during the water-assisted injection process were analyzed by a water-assisted injection molding analysis. In addition, the changes in the residual wall thickness accompanying changes in the process conditions were compared with the analysis results by considering water-assisted injection molding based on gas-assisted injection molding. Furthermore, by comparing the cooling characteristics and inner wall surface qualities corresponding to the formation of the hollow section by gas and water injections, a water-assisted injection molding technique was proposed for manufacturing hollow products with functionality.

Influence of Process Parameters on Plastic Injection Molding of Automobile Interior Trim

2011 ◽  
Vol 189-193 ◽  
pp. 1675-1680
Author(s):  
Qing Qing Liu ◽  
Lin Hua ◽  
Wei Guo
Keyword(s):  
Mold Temperature ◽  
Process Conditions ◽  
Injection Time ◽  
Molding Process ◽  
Melt Temperature ◽  
Influence Of Process Parameters ◽  
Packing Pressure ◽  
Optimal Setting ◽  
Injection Molded ◽  
Packing Time

The influence of process conditions on the formability of injection-molded PX0034 (9% talc-filled PP) automobile B column mounting trim applied as a model has been studied in current work. This study has been focused on the interactive influence of melt temperature and mold temperature, the interactive influences of injection time and packing time and the influences of packing pressure. Weighting the effect of optimization is by formability including the values of pressure at V/P switchover, volumetric shrinkage differential at ejection, and maximum warpage. Aforementioned values were obtained by numerical simulation of the whole molding process using commercial dedicated code Moldflow. Results indicate that the combination of mold temperature at 25 °C, melt temperature at 220 °C, injection time at 2.2 s, packing time at 16 s and packing pressure at 90% of the filling pressure is the optimal setting for formability of this trim. The simulation results obtained under the optimized parameters are that the pressure at V/P switchover is 27.29 Mpa, the shrinkage differential at ejection is 6.55 %, and maximum warpage is 3.072 mm. Good correlation is highlighted between the experiments and the simulations by comparing effects of the global optimization in formability, which verifies the validity of the optimal combination.

Correlation Between Mechanical Properties in Standard Test Specimens and Injection Molded Thin-Wall Parts

2013 ◽  
Author(s):  
Laurentiu I. Sandu ◽  
Felicia Stan ◽  
Catalin Fetecau
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Injection Molding ◽  
Process Conditions ◽  
Thin Wall ◽  
Optimal Process ◽  
Melt Temperature ◽  
Molded Parts ◽  
Injection Molded

In this paper, we investigated the effect of injection molding parameters on the mechanical properties of thin-wall injection molded parts. A four-factor (melt temperature, mold temperature, injection speed and packing pressure) and three-level fractional experimental design was performed to investigate the influence of each factor on the mechanical properties and determine the optimal process conditions that maximize the mechanical properties of the part using the signal-to-noise (S/N) ratio response. The mechanical properties (e.g., elastic modulus, yield strength and strain at break) were measured by tensile tests at room temperature, at a crosshead speed of 5 mm/min, and compared with those of the injection-molded specimens. The experimental results showed that the tensile properties were highly dependent on the injection molding parameters, regardless of the type of the specimens. The values of Young modulus and yield strength of the injection-molded specimens were lower than those of the injection-molded parts, while the elongation at break was considerably lower for the injection-molded parts. The optimal process conditions were strongly dependent on the measured performance quantities (elastic modulus, yield strength and strain at break).

Micro-Injection Molding of Polymer Nanocomposites Composition-Process-Properties Relationship

2021 ◽  
Vol 36 (3) ◽  
pp. 276-286
Author(s):  
Z. Dekel ◽  
S. Kenig
Keyword(s):  
Mechanical Properties ◽  
Plug Flow ◽  
Volume Resistivity ◽  
Process Conditions ◽  
Polyamide 66 ◽  
Fountain Flow ◽  
Microinjection Molding ◽  
Injection Molded ◽  
Composition Process ◽  
Rheological Percolation

Abstract The mechanical, electrical, thermal, and rheological properties of micro injection molded nanocomposites comprising 2% and 5% carbon nanotubes (CNTs) incorporated in polycarbonate (PC), and polyamide 66 (PA) were studied. The design of experiments method was used to investigate the composition-process – properties relationship. Results indicated that the process variables significantly affected the flow patterns and resulting morphology during the filling stage of the microinjection molding (lIM) process, using 0.45 mm diameter lIM samples. Two distinct flow regimes have been identified in lIM using the low cross-section samples. The first was a conventional “fountain flow,” which resulted in a skin/core structure and reduced volume resistivity up to 10 X cm in the case of 5% CNTs and up to 100 X cm in 2% CNTs, in both polymers, respectively. In addition, inferior mechanical properties were obtained, attributed to polymer degradation under high shear rate conditions, when practicing high injection speeds, high mold temperatures, and high screw rotation velocities. The second was a “plug flow” due to wall slippage, obtained under low injection speeds, low mold temperatures, and low rotation velocities, leading to a substantial increase in modulus of elasticity (60%) with increased electrical resistivity up to 103 X cm for 5% CNTs and 105 X cm for 2% CNTs, respectively. The rheological percolation threshold was obtained at 2% CNTs while the electrical threshold was attained at 0.4% CNTs, in both polymers. It was concluded that in lIM, the process conditions should be closely monitored. In the case of high viscous heating, degradation of mechanical properties was obtained, while skin- core morphology formation enhanced electrical conductivity.

Geometry-Based Index for Predicting Sink Mark in Plastic Parts

1991 ◽  
Author(s):  
Kurt Beiter ◽  
Kosuke Ishii ◽  
Lee Hornberger
Keyword(s):  
Process Conditions ◽  
Plastic Part ◽  
Design Rules ◽  
Packing Pressure ◽  
Molded Parts ◽  
Injection Molded ◽  
Form Features ◽  
Plastic Parts ◽  
Sink Mark

Abstract This paper describes the development of geometry-based indices that predict sink mark depth in injection molded parts. Plastic part designers need such indices to incorporate manufacturability concerns at the conceptual stage of design. These indices apply to several form features so engineers do not have to check different design rules for each geometry element. First, we propose a geometry-based sink index that can be used to predict sink mark depth as a function of process conditions such as packing pressure. Next, we explain how this relationship is identified through experiments. We also describe HyperDesign/Plastics, a Macintosh-based design aid that incorporates the sink index.

scholarly journals Effects of Injection Molding Screw Tips on Polymer Mixing

2018 ◽  
Vol 62 (3) ◽  
pp. 241-246 ◽  
Author(s):  
Dániel Török ◽  
József Gábor Kovács
Keyword(s):  
Injection Molding ◽  
Processing Parameters ◽  
Raw Material ◽  
Molding Machine ◽  
Surface Color ◽  
Melt Temperature ◽  
Injection Molding Machine ◽  
Aesthetic Appearance ◽  
Molded Parts ◽  
Injection Molded

In all fields of industry it is important to produce parts with good quality. Injection molded parts usually have to meet strict requirements technically and aesthetically. The aim of the measurements presented in our paper is to investigate the aesthetic appearance, such as surface color homogeneity, of injection molded parts. It depends on several factors, the raw material, the colorants, the injection molding machine and the processing parameters. In this project we investigated the effects of the injection molding machine on surface color homogeneity. We focused on injection molding screw tips and investigated five screw tips with different geometries. We produced flat specimens colored with a masterbatch and investigated color homogeneity. To evaluate the color homogeneity of the specimens, we used digital image analysis software developed by us. After that we measured the plastication rate and the melt temperature of the polymer melt because mixing depends on these factors. Our results showed that the screw tips (dynamic mixers) can improve surface color homogeneity but they cause an increase in melt temperature and a decrease in the plastication rate.

Prediction of crystallinity profile and eject time of injection molded parts using finite element method (FEM)

e-Polymers ◽  
2009 ◽  
Vol 9 (1) ◽  
Author(s):  
Mehdi Mostafaiyan ◽  
Farhad Sharif
Keyword(s):  
Finite Element ◽  
Degree Of Crystallinity ◽  
Element Analysis ◽  
Melt Temperature ◽  
Crystalline Polymers ◽  
Molded Parts ◽  
Time Part ◽  
Injection Molded ◽  
The Subject

AbstractQuality of injection molded parts of semi-crystalline polymers has been the subject of intense interest from both analytical and industrial points of view. Crystallinity profile plays an important role in determining mechanical properties of a part and its quality. Therefore it is important to analyze the effect of injection molding parameters on the crystallinity profile of the molded parts. In this study, finite element analysis has been used to solve the equations of mass, momentum, and energy conservation simultaneously with the equation of crystallization kinetics to predict melt front, its solidification and crystallinity profile. The results from our numerical analysis have been compared with the reported experimental results. Furthermore, progress of the crystallization is proposed to be a proper criterion for estimation of the eject time. Finally, the effects of mold and melt temperature on the eject time; part temperature and average degree of crystallinity, for a specific compound are also presented.

Sign in / Sign up

Export Citation Format

Share Document