The Effect of Cellulose Fibers on the Formation of Petroleum-Based and Bio-Based Polyurethane Foams

2019 ◽  
Vol 803 ◽  
pp. 371-376
Author(s):  
Lady Jaharah Y. Jabber ◽  
Jessalyn C. Grumo ◽  
Arnold C. Alguno ◽  
Arnold A. Lubguban ◽  
Rey Y. Capangpangan
Keyword(s):  
Thermal Stability ◽  
Cellulose Fiber ◽  
Cellulose Fibers ◽  
Polyurethane Foams ◽  
Ananas Comosus ◽  
Scanning Electron Micrographs ◽  
Cell Structures ◽  
Higher Temperature ◽  
The Fourier Transform ◽  
Thermal Insulations

We report on the effect of cellulose fibers on the formation of petroleum-based and bio-based polyurethane foams. The fabricated polyurethane foams (PUF) were done by reacting isocyanate with petroleum-based polyol and epoxidized soybean oil (ESBO)-based polyols via hand mixing. The addition of cellulose fibers extracted from pineapple (Ananas comosus) leaf was done to enhance the properties of the fabricated PUF. Experimental results revealed that surface morphology of the fabricated polyurethane foams with addition of cellulose fibers remain the well-defined cell structures as shown in the scanning electron micrographs although few cell ruptures were observed. Likewise, the presence of the vibrational modes of the NCO and OH were confirmed in the Fourier transform infrared (FTIR) spectra suggesting that successful formation of polyurethane foams takes place. The thermogravimetric results revealed that much higher thermal stability for the 100% ESBO-based PUF with cellulose fibers due to the presence of cellulose and triglycerides in the ESBO-based polyols which both degrades at higher temperature. This suggest that 100% ESBO-based PUF with cellulose fiber exhibit higher thermal stability provides promising application for thermal insulations.

Calcium phosphate compound–cellulose fiber composite material prepared in soaking medium at 36.5–60 °C

1998 ◽  
Vol 13 (4) ◽  
pp. 922-925 ◽  
Author(s):  
Yoshiyuki Yokogawa ◽  
Motohiro Toriyama ◽  
Yukari Kawamoto ◽  
Kaori Nishizawa ◽  
Fukue Nagata ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Fiber Composite ◽  
Simulated Body Fluid Solution ◽  
Cellulose Fiber ◽  
Cellulose Fibers ◽  
Calcium Phosphate Coating ◽  
Soaking Time ◽  
Higher Temperature ◽  
Sbf Solution ◽  
Soaking Temperature

Calcium phosphate growth on cellulose fibers phosphorylated in 1.5 × SBF (simulated body fluid) solution at various temperatures from 36.5–60 °C was studied. Cellulose fibers phosphorylated by using urea and H3PO4 and then soaked in saturated Ca(OH)2 solution at ambient temperature were found to stimulate the growth of a calcium phosphate coating on their surfaces after soaking in 1.5 × SBF solution for as little as one day. Soaking in 1.5 × SBF solution at higher temperature produced a thicker layer of calcium phosphate on the fibers, which may be due to the decrease of solubility of calcium phosphate. The specific surface area of the coatings decreased with an increase of soaking temperature and soaking time in 1.5 × SBF solution.

scholarly journals Polyurethane Composite Foams Synthesized Using Bio-Polyols and Cellulose Filler

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3474
Author(s):  
Katarzyna Uram ◽  
Milena Leszczyńska ◽  
Aleksander Prociak ◽  
Anna Czajka ◽  
Michał Gloc ◽  
...  
Keyword(s):  
Cross Sections ◽  
Raw Materials ◽  
Polyurethane Foams ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Polyurethane Composite ◽  
Composite Foams ◽  
Closed Cell ◽  
Ft Ir ◽  
The Fourier Transform

Rigid polyurethane foams were obtained using two types of renewable raw materials: bio-polyols and a cellulose filler (ARBOCEL® P 4000 X, JRS Rettenmaier, Rosenberg, Germany). A polyurethane system containing 40 wt.% of rapeseed oil-based polyols was modified with the cellulose filler in amounts of 1, 2, and 3 php (per hundred polyols). The cellulose was incorporated into the polyol premix as filler dispersion in a petrochemical polyol made using calenders. The cellulose filler was examined in terms of the degree of crystallinity using the powder X-ray diffraction PXRD -and the presence of bonds by means of the fourier transform infrared spectroscopy FT-IR. It was found that the addition of the cellulose filler increased the number of cells in the foams in both cross-sections—parallel and perpendicular to the direction of the foam growth—while reducing the sizes of those cells. Additionally, the foams had closed cell contents of more than 90% and initial thermal conductivity coefficients of 24.8 mW/m∙K. The insulation materials were dimensionally stable, especially at temperatures close to 0 °C, which qualifies them for use as insulation at low temperatures.

scholarly journals Improved thermally stable oligoetherols from 6-aminouracil, ethylene carbonate and boric acid

2019 ◽  
Vol 17 (1) ◽  
pp. 1080-1086
Author(s):  
Elżbieta Chmiel-Szukiewicz
Keyword(s):  
Thermal Stability ◽  
Thermal Properties ◽  
Boric Acid ◽  
Ethylene Carbonate ◽  
Pyrimidine Ring ◽  
Polyurethane Foams ◽  
High Thermal Stability ◽  
H Nmr ◽  
Maldi Tof ◽  
Instrumental Methods

AbstractSyntheses of oligoetherols with a 1,3-pyrimidine ring and boron atoms using 6-aminouracil, ethylene carbonate and boric acid has been proposed. The structure of the obtained products were determined by instrumental methods (IR, 1H-NMR and MALDI-ToF spectra). The physicochemical and thermal properties of oligoetherols were examined. The products were characterized by high thermal stability. Based on the tests performed, it was found that oligoetherols obtained from 6-aminouracil, boric acid and ethylene carbonate are suitable for the manufacturing of polyurethane foams with improved thermal stability and reduced flammability.

scholarly journals Fabrication and Application of SERS-Active Cellulose Fibers Regenerated from Waste Resource

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2142
Author(s):  
Shengjun Wang ◽  
Jiaqi Guo ◽  
Yibo Ma ◽  
Alan X. Wang ◽  
Xianming Kong ◽  
...  
Keyword(s):  
Au Nanoparticles ◽  
Cellulose Fiber ◽  
Cellulose Fibers ◽  
Regenerated Cellulose ◽  
Sers Substrate ◽  
Au Nps ◽  
Convenient Approach ◽  
Theoretical Simulations ◽  
Difference Time ◽  
Raman Probe

The flexible SERS substrate were prepared base on regenerated cellulose fibers, in which the Au nanoparticles were controllably assembled on fiber through electrostatic interaction. The cellulose fiber was regenerated from waste paper through the dry-jet wet spinning method, an eco-friendly and convenient approach by using ionic liquid. The Au NPs could be controllably distributed on the surface of fiber by adjusting the conditions during the process of assembling. Finite-difference time-domain theoretical simulations verified the intense local electromagnetic fields of plasmonic composites. The flexible SERS fibers show excellent SERS sensitivity and adsorption capability. A typical Raman probe molecule, 4-Mercaptobenzoicacid (4-MBA), was used to verify the SERS cellulose fibers, the sensitivity could achieve to 10−9 M. The flexible SERS fibers were successfully used for identifying dimetridazole (DMZ) from aqueous solution. Furthermore, the flexible SERS fibers were used for detecting DMZ from the surface of fish by simply swabbing process. It is clear that the fabricated plasmonic composite can be applied for the identifying toxins and chemicals.

Research on Mechanical Properties of Several New Regenerated Cellulose Fibers

2011 ◽  
Vol 332-334 ◽  
pp. 489-495 ◽  
Author(s):  
Rong Zhou ◽  
Ming Xia Yang
Keyword(s):  
Mechanical Properties ◽  
Phase Change Materials ◽  
Cellulose Fiber ◽  
Cellulose Fibers ◽  
Regenerated Cellulose ◽  
Pulp Fiber ◽  
Pulp Fibers ◽  
Bast Fiber ◽  
Bamboo Pulp ◽  
Lyocell Fiber

Regenerated cellulose fiber is the most widely-used and most variety of cellulose fiber. Five categories and ten kinds of fibers such as lyocell fiber, modal fiber, bamboo pulp fiber, sheng-bast fiber, Outlast viscose fiber were chosen as the research object. The strength property and elasticity of fibers in dry and wet state were tested and analysis. The comprehensive performances of fabrics were studied and mechanical properties of the fibers were listed in the order from good to bad by grey clustering analysis. The results show lyocell G100 and lyocell LF have better comprehensive mechanical properties ,while other new regenerated cellulose fibers’ comprehensive mechanical properties are general. Among these fibers modal fiber’s comprehensive mechanical properties are slightly better than sheng-bast fibers’ and bamboo pulp fibers’. Modal fiber, sheng-bast fiber and Bamboo pulp fiber have no significantly poor single parameter and all of them have better comprehensive mechanical properties than various viscose fibers. Outlast viscose in which has been added phase change materials sensitive to temperature by Microcapsule techniques fundamentally keeps similar comprehensive mechanical properties with other regenerated cellulose fibers,but its properties decline slightly .

Properties of Flame-Retardant Cellulose Fibers Prepared from Cellulose[Amim]Cl Dope Solution

2011 ◽  
Vol 236-238 ◽  
pp. 1152-1155
Author(s):  
Lei Gao ◽  
Bo Wen Cheng ◽  
Jun Song ◽  
Zeng Geng Guo ◽  
Fei Lu ◽  
...  
Keyword(s):  
Flame Retardant ◽  
Flame Retardants ◽  
Simultaneous Thermal Analysis ◽  
Cellulose Fiber ◽  
Cellulose Fibers ◽  
Structure And Properties ◽  
Fiber Structure ◽  
Fiber Degradation ◽  
Dope Solution ◽  
Flame Retardant Properties

This paper has studied the structure and flame-retardant properties of flame-retardant cellulose fiber with DDPSN as flame retardant. The flame retardants was uniformly dispersed in the cellulose /[Amim]Cl Solution to obtain the good spinnable dope, then the dope was wet-spun. Effects of the flame-retardant contention the fiber structure and properties were investigated. The surface of the flame-retardant cellulose fiber was observed using field emission scanning electron microscope (FESEM). Besides, through the Simultaneous thermal analysis, it has been shown that, with the increase of fame retardant, the degree of fame resistance was obviously improved. The flame retardant acted greatly in condensed phase during the fiber degradation and remained mainly in residues after degradation, the experiments show that the flame-retardant properties of flame-retardant cellulose fiber with 20wt% DDPSN was obvious.

Cryogenic thermal insulating and mechanical properties of rigid polyurethane foams blown with hydrofluoroolefin: Effect of perfluoroalkane

2021 ◽  
pp. 0021955X2110626
Author(s):  
Tae Seok Kim ◽  
Yeongbeom Lee ◽  
Chul Hyun Hwang ◽  
Kwang Ho Song ◽  
Woo Nyon Kim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Stability ◽  
Cell Size ◽  
Thermal Insulation ◽  
Coefficient Of Thermal Expansion ◽  
Lower Surface ◽  
Polyurethane Foams ◽  
Insulation Material ◽  
Pu Foams

The effect of perfluoroalkane (PFA) on the morphology, thermal conductivity, mechanical properties and thermal stability of rigid polyurethane (PU) foams was investigated under ambient and cryogenic conditions. The PU foams were blown with hydrofluorolefin. Morphological results showed that the minimum cell size (153 μm) was observed when the PFA content was 1.0 part per hundred polyols by weight (php). This was due to the lower surface tension of the mixed polyol solution when the PFA content was 1.0 php. The thermal conductivity of PU foams measured under ambient (0.0215 W/mK) and cryogenic (0.0179 W/mK at −100°C) conditions reached a minimum when the PFA content was 1.0 php. The low value of thermal conductivity was a result of the small cell size of the foams. The above results suggest that PFA acted as a nucleating agent to enhanced the thermal insulation properties of PU foams. The compressive and shear strengths of the PU foams did not appreciably change with PFA content at either −170°C or 20°C. However, it shows that the mechanical strengths at −170°C and 20°C for the PU foams meet the specification. Coefficient of thermal expansion, and thermal shock tests of the PU foams showed enough thermal stability for the LNG carrier’s operation temperature. Therefore, it is suggested that the PU foams blown by HFO with the PFA addition can be used as a thermal insulation material for a conventional LNG carrier.

scholarly journals Rigid Polyurethane Foams Modified with Biochar

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5616
Author(s):  
Katarzyna Uram ◽  
Maria Kurańska ◽  
Jacek Andrzejewski ◽  
Aleksander Prociak
Keyword(s):  
Thermal Conductivity ◽  
Thermal Stability ◽  
Thermal Insulation ◽  
Foam Cells ◽  
Polyurethane Foams ◽  
Cross Sectional ◽  
Rigid Polyurethane Foams ◽  
Insulation Materials

This paper presents results of research on the preparation of biochar-modified rigid polyurethane foams that could be successfully used as thermal insulation materials. The biochar was introduced into polyurethane systems in an amount of up to 20 wt.%. As a result, foam cells became elongated in the direction of foam growth and their cross-sectional areas decreased. The filler-containing systems exhibited a reduction in their apparent densities of up to 20% compared to the unfilled system while maintaining a thermal conductivity of 25 mW/m·K. Biochar in rigid polyurethane foams improved their dimensional and thermal stability.

Systematic Characterization of Different Quaternary Ammonium Salts to be Used in Organoclays

2012 ◽  
Vol 727-728 ◽  
pp. 1552-1556
Author(s):  
Renata Barbosa ◽  
Dayanne Diniz Souza ◽  
Edcleide Maria Araújo ◽  
Tomás Jefférson Alves de Mélo
Keyword(s):  
Thermal Stability ◽  
Quaternary Ammonium ◽  
Chemical Structure ◽  
Quaternary Ammonium Salts ◽  
Ammonium Salts ◽  
Degradation Mechanisms ◽  
Scanning Calorimetry ◽  
Higher Temperature ◽  
Thermal Stability Of

Studies of degradation have verified that the decomposition of some quaternary ammonium salts can begin to be significant at the temperature of about 180 ° C and like most thermoplastics are processed at least around this temperature, the thermal stability of the salt in clay should always be considered. Some salts are more stable than others, being necessary to study the degradation mechanisms of each case. In this work, four quaternary ammonium salts were characterized by differential scanning calorimetry (DSC) and thermogravimetry (TG). The results of DSC and TG showed that the salts based chloride (Cl-) anion begin to degrade at similar temperatures, while the salt based bromide (Br-) anion degrades at higher temperature. Subsequently, a quaternary ammonium salt was chosen to be used in organoclays, depending on its chemical structure and its thermal behavior.

scholarly journals Effect of High Temperature on the Electrochemical and Optical Properties of Emeraldine Salt Doped with DBSA and Sulfuric Acid

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Salma Gul ◽  
Anwar-ul-Haq Ali Shah ◽  
Salma Bilal
Keyword(s):  
Thermal Stability ◽  
Cyclic Voltammetry ◽  
Sulfuric Acid ◽  
Effect Of Temperature ◽  
Visible Spectroscopy ◽  
Emeraldine Salt ◽  
Higher Temperature ◽  
Stability Effect ◽  
Thermal Stability Of ◽  
Comprehensive Study

A comprehensive study of thermally treated polyaniline in its emeraldine salt form is presented here. It offers an understanding of the thermal stability of the polymer. Emeraldine salt was prepared by a novel emulsion polymerization pathway using dodecylbenzene sulfonic acid and sulfuric acid together as dopants. The effect of temperature and heating rate on the degradation of this emeraldine salt was studied via thermogravimetric analysis. The thermally analyzed sample was collected at various temperatures, that is, 250, 490, 500, and 1000°C. The gradual changes in the structure of the emeraldine salt were followed through cyclic voltammetry, Fourier transform infrared spectroscopy, and ultraviolet-visible spectroscopy. Results demonstrate that emeraldine salt shows high thermal stability up to 500°C. This is much higher working temperature for the use of emeraldine salt in higher temperature applications. Further heat treatment seems to induce deprotonation in emeraldine salt. Cyclic voltammetry and ultraviolet-visible spectroscopy revealed that complete deprotonation takes place at 1000°C where it loses its electrical conductivity. It is interesting to note that after the elimination of the dopants, the basic backbone of emeraldine salt was not destroyed. The results reveal that the dopants employed have a stability effect on the skeleton of emeraldine salt.

Sign in / Sign up

Export Citation Format

Share Document