Processing and Characterization of Magnesium Alloys

2005 ◽  
Vol 488-489 ◽  
pp. 401-404
Author(s):  
Hwa Chul Jung ◽  
Kwang Seon Shin
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloys ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Casting Process ◽  
World Market ◽  
Damping Capacity ◽  
Corrosion Properties ◽  
Research Activities

Magnesium has the lowest density among the commercially available structural metals and its superior physical and mechanical properties make magnesium alloys extremely attractive for applications requiring lightweight, good castability and damping capacity. In recent years, due to the demand for lightweight magnesium components in the automobile and electronic industries, the world market for magnesium alloys has increased rapidly. At the same time, the research activities on manufacturing process and characterization of magnesium alloys have also increased significantly. The research activities have been concentrated on many different fields, including the development of high pressure die casting process and semi-solid processing, development of high strength wrought alloys and components, and characterization of microstructure, mechanical properties as well as corrosion properties. In this article, the recent progresses achieved in these research areas at Seoul National University will be introduced.

scholarly journals Microstructure and mechanical properties of as-cast and annealed high strength low alloy steel

2019 ◽  
Vol 8 (4) ◽  
pp. 1
Author(s):  
Bárbara Ferreira de Oliveira ◽  
Michel Picanço Oliveira ◽  
Luis Augusto Hernandez Terrones ◽  
Márcia Giardinieri de Azevedo ◽  
Leonardo Barbosa Godefroid
Keyword(s):  
Mechanical Properties ◽  
Hsla Steel ◽  
Cast Steel ◽  
High Strength ◽  
Calcium Content ◽  
Casting Process ◽  
Mechanical Tests ◽  
Solidification Structure ◽  
Microstructure And Mechanical Properties

This paper presents a study on the microstructure and mechanical properties of a microalloyed HSLA steel solidified by continuous casting process and annealed at 1100 °C for 1 hour. The techniques of confocal microscopy, scanning electron microscopy and hardness, tensile and Charpy mechanical tests were used. The results of this research showed that the microstructure of the sample in the as-received condition was mainly composed of acicular ferrite and aggregates of ferrite and carbides. Non-metallic inclusion characterization of as-cast steel showed that calcium content was not enough to modify the morphology of some aluminates. After thermal treatment, the initial microstructure was transformed into polygonal ferrite and pearlite. In both conditions, different types of precipitates were found, which were classified according to their distribution in the microstructure. The steel with solidification structure showed a higher tensile strength, but its application would be unlikely in components that require good impact strength.

Characterization of physical and mechanical properties of aluminium based composites reinforced with titanium diboride particulates

2020 ◽  
pp. 002199832098080
Author(s):  
Dipankar Dey ◽  
Abhijit Bhowmik ◽  
Ajay Biswas
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Titanium Diboride ◽  
Microstructural Analysis ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Casting Process ◽  
Matrix Alloy ◽  
Stir Casting ◽  
Sem Analysis

Particulate reinforced aluminium matrix composites are one of the most attractive approaches for applications where high strength and hardness combinations are necessary. The aspiration of this study is to investigate the effect of titanium diboride addition on physical and mechanical properties of Al2024-TiB2 composites manufactured using stir casting route, by varying the weight percentages (wt.%) (0, 3, 6 and 9 percent) of titanium diboride particulates. During the casting process, stirring time and speed were kept constant and same for all the composites. Microstructural analysis demonstrates uniformity in TiB2 distribution and also strong matrix-reinforcement bonding which can be as a result of magnesium addition and preheating of titanium diboride particles before incorporating into the molten aluminium. With an increment in the wt.% of TiB2 particulates, hardness and tensile strength of the prepared composites improved, a significant improvement in hardness as well as tensile strength is encountered in Al2024-9% TiB2 composite, which is 44.94% and 35.49% higher than Al2024 matrix alloy, respectively. SEM analysis of the fractured surfaces revealed that the mode of fracture of unreinforced material is purely ductile but reinforced material fractured by nucleation of cracks and plastic deformation.

PREPARATION AND CHARACTERIZATION OF REPROCESSED COMPOSITES OF POLYPROPYLENE REINFORCED BY WOOD FIBERS: PHYSICAL AND MECHANICAL PROPERTIES

2017 ◽  
Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Fibers

scholarly journals Properties of High-Strength Flowable Mortar Reinforced with Palm Fibers

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Test Results ◽  
Palm Fiber ◽  
Toughness Index ◽  
Strength And Toughness

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.

Characterization of particleboard made from oil heat-treated rubberwood particles at different mixing ratios

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 6795-6810
Author(s):  
Nurul Fatiha Osman ◽  
Paimon Bawon ◽  
Seng Hua Lee ◽  
Pakhriazad Hassan Zaki ◽  
Syeed SaifulAzry Osman Al-Eldrus ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Oil Content ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Thermal Characterization ◽  
High Dimensional ◽  
Mixing Ratios ◽  
Uf Resin ◽  
Heat Treated

Particleboard was produced by mixing oil heat-treated rubberwood particles at different ratios, with the goal of achieving high dimensional stability. Rubberwood particles were soaked in palm oil for 2 h and heat treated at 200 °C for 2 h. The treated particles were soaked in boiling water for 30 min to remove oil and were tested for chemical alteration and thermal characterization via Fourier-transform infrared spectroscopy and thermogravimetric analysis. Particleboard was fabricated by mixing treated rubberwood particles (30%, 50%, and 70%) with untreated particles (70%, 50%, and 30%, respective to previous percentages) and bonded with urea-formaldehyde (UF) resin. The results revealed that oil-heat treated particles had greater thermal stability than the untreated particles. The addition of oil heat treated particles improved the physical properties of the particleboard with no significant reduction in mechanical strength. However, this was only valid for ratios of 70% untreated to 30% treated and 50% untreated to 50% treated. When a ratio of 70% oil heat treated particles was used, both the physical and mechanical properties were reduced drastically, due to bonding interference caused by excessive oil content. Particleboard made with a ratio of 5:5 (treated to untreated) exhibited the best physical and mechanical properties.

CHARACTERIZATION OF HYDROXYAPATITE/TI6AL4V COMPOSITE POWDER UNDER VARIOUS SINTERING TEMPERATURE

2015 ◽  
Vol 75 (7) ◽  
Author(s):  
Amir Arifin ◽  
Abu Bakar Sulong ◽  
Norhamidi Muhamad ◽  
Junaidi Syarif
Keyword(s):  
Mechanical Properties ◽  
Composite Powder ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Different Temperatures ◽  
Two Phases ◽  
Work Interaction

Hydroxyapatite (HA) has been widely used in biomedical applications due to its excellent biocompatibility. However, Hydroxyapatite possesses poor mechanical properties and only tolerate limited loads for implants. Titanium is well-known materials applied in implant that has advantage in mechanical properties but poor in biocompatibility. The combination of the Titanium alloy and HA is expected to produce bio-implants with good in term of mechanical properties and biocompatabilty. In this work, interaction and mechanical properties of HA/Ti6Al4V was analyzed. The physical and mechanical properties of HA/Ti6Al4V composite powder obtained from compaction (powder metallurgy) of 60 wt.% Ti6Al4V and 40 wt.% HA and sintering at different temperatures in air were investigated in this study. Interactions of the mixed powders were investigated using X-ray diffraction. The hardness and density of the HA/Ti6Al4V composites were also measured. Based on the results of XRD analysis, the oxidation of Ti began at 700 °C. At 1000 °C, two phases were formed (i.e., TiO2 and CaTiO3). The results showed that the hardness HA/Ti6Al4V composites increased by 221.6% with increasing sintering temperature from 700oC to 1000oC. In contrast, the density of the composites decreased by 1.9% with increasing sintering temperature. 

scholarly journals Micro- and Macroscale Consequences of Interactions between CO2 and Shale Rocks

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1167 ◽  
Author(s):  
Mohammad H. Bhuiyan ◽  
Nicolaine Agofack ◽  
Kamila M. Gawel ◽  
Pierre R. Cerasi
Keyword(s):  
Mechanical Properties ◽  
Experimental Approach ◽  
Oil And Gas ◽  
Review Paper ◽  
State Of The Art ◽  
Co2 Storage ◽  
Physical And Mechanical Properties ◽  
Acoustic Measurements ◽  
Carbon Dioxide Co2

In carbon storage activities, and in shale oil and gas extraction (SOGE) with carbon dioxide (CO2) as stimulation fluid, CO2 comes into contact with shale rock and its pore fluid. As a reactive fluid, the injected CO2 displays a large potential to modify the shale’s chemical, physical, and mechanical properties, which need to be well studied and documented. The state of the art on shale–CO2 interactions published in several review articles does not exhaust all aspects of these interactions, such as changes in the mechanical, petrophysical, or petrochemical properties of shales. This review paper presents a characterization of shale rocks and reviews their possible interaction mechanisms with different phases of CO2. The effects of these interactions on petrophysical, chemical and mechanical properties are highlighted. In addition, a novel experimental approach is presented, developed and used by our team to investigate mechanical properties by exposing shale to different saturation fluids under controlled temperatures and pressures, without modifying the test exposure conditions prior to mechanical and acoustic measurements. This paper also underlines the major knowledge gaps that need to be filled in order to improve the safety and efficiency of SOGE and CO2 storage.

Sign in / Sign up

Export Citation Format

Share Document