Fatigue Properties of a Ck45 Steel Coated with a Post-Heat Treated Ni-Cu-P Electroless Deposit

2006 ◽  
Vol 514-516 ◽  
pp. 574-578
Author(s):  
Sasan Yazdani ◽  
N. Parvini-Ahmadi ◽  
Tohid Saeid
Keyword(s):  
Fatigue Life ◽  
Fatigue Testing ◽  
Crack Nucleation ◽  
Fatigue Cracks ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Interfacial Cracks ◽  
Heat Treated ◽  
Base Steel ◽  
Surface Notch

The Fatigue tests under rotating bending conditions have been conducted on samples of a quenched and tempered Ck45 steel in two different conditions: (a) uncoated, (b) coated with an electroless Ni-Cu-P deposit, followed by a post-heat treatment (PHT) at 673 K for 1 h. Such a deposit had a thickness of approximately 10µm, with Cu and P contents of 6wt.% and 13.7wt.% respectively. The results indicate that plating the base steel with this kind of deposit leads to a reduction of the fatigue life of the material. The reduction in fatigue life has been quantified in terms of the Basquin parameters of the materials tested under different conditions. The microscopic observation of the fracture surfaces of the samples indicates that the reduction in fatigue life is associated with the nucleation of fatigue cracks on the coating-substrate interface and the deposit remains well adhered to substrate during fatigue testing since interfacial cracks have been very rarely observed. It is therefore concluded that, in the present case, the interface acts as a surface crack source or surface notch, which decreases the fatigue life of the coated material by reducing the crack nucleation stage.

scholarly journals The Influence of Laser Shock Peening on Fatigue Properties of AA2024-T3 Alloy with a Fastener Hole

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 495
Author(s):  
Ruslan Sikhamov ◽  
Fedor Fomin ◽  
Benjamin Klusemann ◽  
Nikolai Kashaev
Keyword(s):  
Fatigue Life ◽  
Fatigue Cracks ◽  
Initial Crack ◽  
Fatigue Tests ◽  
Laser Shock Peening ◽  
Fatigue Properties ◽  
Hole Drilling ◽  
Laser Shock ◽  
Fastener Hole ◽  
Shock Peening

The objective of the present study was to estimate the influence of laser shock peening on the fatigue properties of AA2024-T3 specimens with a fastener hole and to investigate the possibility to heal the initial cracks in such specimens. Fatigue cracks of different lengths were introduced in the specimens with a fastener hole before applying laser shock peening. Deep compressive residual stresses, characterized by the hole drilling method, were generated into the specimens by applying laser shock peening on both sides. Subsequently, the specimens were subjected to fatigue tests. The results show that laser shock peening has a positive effect regarding the fatigue life improvement in the specimens with a fastener hole. In addition, laser shock peening leads to a healing effect on fatigue cracks. The efficiency of this effect depends on the initial crack length. The effect of laser shock peening on the fatigue life periods was determined by using resonant frequency graphs.

scholarly journals Fatigue Testing of Wearable Sensing Technologies: Issues and Opportunities

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4070
Author(s):  
Andrea Karen Persons ◽  
John E. Ball ◽  
Charles Freeman ◽  
David M. Macias ◽  
Chartrisa LaShan Simpson ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Prediction Models ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
Wearable Sensors ◽  
Fatigue Tests ◽  
Proof Of Concept ◽  
Cycle Fatigue ◽  
Wearable Sensing ◽  
Failure Data

Standards for the fatigue testing of wearable sensing technologies are lacking. The majority of published fatigue tests for wearable sensors are performed on proof-of-concept stretch sensors fabricated from a variety of materials. Due to their flexibility and stretchability, polymers are often used in the fabrication of wearable sensors. Other materials, including textiles, carbon nanotubes, graphene, and conductive metals or inks, may be used in conjunction with polymers to fabricate wearable sensors. Depending on the combination of the materials used, the fatigue behaviors of wearable sensors can vary. Additionally, fatigue testing methodologies for the sensors also vary, with most tests focusing only on the low-cycle fatigue (LCF) regime, and few sensors are cycled until failure or runout are achieved. Fatigue life predictions of wearable sensors are also lacking. These issues make direct comparisons of wearable sensors difficult. To facilitate direct comparisons of wearable sensors and to move proof-of-concept sensors from “bench to bedside,” fatigue testing standards should be established. Further, both high-cycle fatigue (HCF) and failure data are needed to determine the appropriateness in the use, modification, development, and validation of fatigue life prediction models and to further the understanding of how cracks initiate and propagate in wearable sensing technologies.

scholarly journals Quantitative Analysis of Inclusion Engineering on the Fatigue Property Improvement of Bearing Steel

Metals ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 476 ◽  
Author(s):  
Chao Gu ◽  
Min Wang ◽  
Yanping Bao ◽  
Fuming Wang ◽  
Junhe Lian
Keyword(s):  
Fatigue Life ◽  
Quantitative Analysis ◽  
Critical Size ◽  
Fatigue Behavior ◽  
Fatigue Cracks ◽  
Fatigue Property ◽  
Bearing Steel ◽  
Fatigue Properties ◽  
Bearing Steels ◽  
Inclusion Distribution

The fatigue property is significantly affected by the inner inclusions in steel. Due to the inhomogeneity of inclusion distribution in the micro-scale, it is not straightforward to quantify the effect of inclusions on fatigue behavior. Various investigations have been performed to correlate the inclusion characteristics, such as inclusion fraction, size, and composition, with fatigue life. However, these studies are generally based on vast types of steels and even for a similar steel grade, the alloy concept and microstructure information can still be of non-negligible difference. For a quantitative analysis of the fatigue life improvement with respect to the inclusion engineering, a systematic and carefully designed study is still needed to explore the engineering dimensions of inclusions. Therefore, in this study, three types of bearing steels with inclusions of the same types, but different sizes and amounts, were produced with 50 kg hot state experiments. The following forging and heat treatment procedures were kept consistent to ensure that the only controlled variable is inclusion. The fatigue properties were compared and the inclusions that triggered the fatigue cracks were analyzed to deduce the critical sizes of inclusions in terms of fatigue failure. The results show that the critical sizes of different inclusion types vary in bearing steels. The critical size of the spinel is 8.5 μm and the critical size of the calcium aluminate is 13.5 μm under the fatigue stress of 1200 MPa. In addition, with the increase of the cleanliness of bearing steels, the improvement of fatigue properties will reach saturation. Under this condition, further increasing of the cleanliness of the bearing steel will not contribute to the improvement of fatigue property for the investigated alloy and process design.

scholarly journals Experimental Design and Validation of an Accelerated Random Vibration Fatigue Testing Methodology

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
Yu Jiang ◽  
Gun Jin Yun ◽  
Li Zhao ◽  
Junyong Tao
Keyword(s):  
Fatigue Life ◽  
Stress Responses ◽  
Life Prediction ◽  
Random Vibration ◽  
Fatigue Testing ◽  
Fatigue Tests ◽  
Fatigue Life Prediction ◽  
Power Spectral ◽  
Vibration Fatigue ◽  
Non Gaussian

Novel accelerated random vibration fatigue test methodology and strategy are proposed, which can generate a design of the experimental test plan significantly reducing the test time and the sample size. Based on theoretical analysis and fatigue damage model, several groups of random vibration fatigue tests were designed and conducted with the aim of investigating effects of both Gaussian and non-Gaussian random excitation on the vibration fatigue. First, stress responses at a weak point of a notched specimen structure were measured under different base random excitations. According to the measured stress responses, the structural fatigue lives corresponding to the different vibrational excitations were predicted by using the WAFO simulation technique. Second, a couple of destructive vibration fatigue tests were carried out to validate the accuracy of the WAFO fatigue life prediction method. After applying the proposed experimental and numerical simulation methods, various factors that affect the vibration fatigue life of structures were systematically studied, including root mean squares of acceleration, power spectral density, power spectral bandwidth, and kurtosis. The feasibility of WAFO for non-Gaussian vibration fatigue life prediction and the use of non-Gaussian vibration excitation for accelerated fatigue testing were experimentally verified.

Low Cycle Fatigue Properties of FGH720Li Superalloy

2021 ◽  
Vol 1035 ◽  
pp. 292-296
Author(s):  
Zi Chao Peng ◽  
Jun Ying Sheng ◽  
Xu Qing Wang ◽  
Yue Tang
Keyword(s):  
Fatigue Life ◽  
Powder Metallurgy ◽  
Applied Stress ◽  
Low Cycle Fatigue ◽  
Influencing Factor ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Nickel Base Superalloy ◽  
Loading Frequency ◽  
Cycle Fatigue

Low cycle fatigue (LCF) properties of a powder metallurgy(PM) nickel base superalloy FGH720Li were systematically studied in this work, including smooth LCF and notched LCF tested at various temperatures and different stress. The relationship between the fatigue life and applied stress was analyzed both for smooth fatigue and notch fatigue tests. The effects of loading frequency and stress ratio on LCF behavior were also studied. As an important influencing factor of the fatigue life in powder metallurgy superalloy, the effect of inclusions on LCF life was also investigated. The results showed that the fatigue properties of FGH720Li alloy was excellent, when tested at the temperature of 450°C and applied stress of 1230MPa, the fatigue life could exceed 5×104 cycles. When tested at 650°C and 1150MPa, the average fatigue life was still beyond 2×105 cycles.

Fatigue Properties of 3D Welded Thin Structures

2020 ◽  
Author(s):  
Seyed M. Allameh ◽  
Avery Lenihan ◽  
Roger Miller ◽  
Hadi Allameh
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Fatigue Testing ◽  
Interfacial Area ◽  
Tensile Tests ◽  
Orientation Dependence ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Mig Welding ◽  
Welded Structures

Abstract Additive manufacturing technology has matured enough to produce real industrial components. A newer method of 3D printing is the deposition of molten metal beads using a MIG weld torch. This involves a 3D printer equipped with a MIG torch layering the metals in desired shapes. It allows the fabrication of components made of MIG weld wires, currently available from various elements including Cu, Al, steel and alloys. Some of these structures made by 3D welding will have applications in critical load bearing conditions. The reliability of such components will be vital in applications where human lives are at stake. Tensile tests are conducted to verify the required strength of the fabricated parts which will undergo monotonic loading; however, fatigue tests are required for cases where cyclic loading will take place. Conventional tensile and fatigue testing requires macro-scale samples. With MIG welding, it is possible to make thin-walled structures. Fatigue testing on samples extracted from thin walls is made possible by microtesting. This study is focused on the mechanical properties of 3D welded structures made from MIG welding wires. Our earlier results showed orientation dependence of mechanical properties in 3D welded structures. They also showed the effect of substrates in expression of the orientation dependence. Welding on metal substrate produces weld beads that are harder at the substrate interfacial area. However, for structures welded on ceramics, the opposite is true. They exhibit a softer substrate interfacial area and a relatively harder top. Our newer results show fatigue properties of structures made by 3D welding. Microsamples measuring 0.2 mm × 0.2 mm × 1.0 mm were extracted from metal beads using a CNC mill along with an EDM. The contours of the samples were machined by milling and the back side was cut by electro discharge machining. Specimens were then polished to the desired size and mounted in the grippers of an E1000 Instron load frame. WaveMatrix® application software from Instron was used to control the machine and to obtain testing data. Fatigue tests were performed, and life cycles were determined for various stress levels up to over 5 million cycles. The preliminary results of tensile tests of these samples show strength levels that are comparable to those of parent metal, in the range of 600–950MPa. Results of fatigue tests show high fatigue lives associated with relatively high stresses. The preliminary results will be presented and the implications of the use of 3D welded rebar in 3D printing of reinforced concrete structures will be discussed.

scholarly journals On the Microstructures and Fatigue Behaviors of 316L Stainless Steel Metal Injection Molded with Gas- and Water-Atomized Powders

Metals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 893 ◽  
Author(s):  
Yongyun Zhang ◽  
Ensheng Feng ◽  
Wei Mo ◽  
Yonghu Lv ◽  
Rui Ma ◽  
...  
Keyword(s):  
Stainless Steel ◽  
316L Stainless Steel ◽  
Fatigue Cracks ◽  
Selective Laser Sintering ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Metal Injection Molding ◽  
Strengthening Effect ◽  
Lower Oxygen ◽  
Order Of Magnitude

316L stainless steel samples are fabricated by metal injection molding using water-atomized and gas-atomized powder with different oxygen contents. The influences of oxygen on the microstructural evolution and fatigue properties of the samples are investigated. The oxygen tends to react with Mn and Si to form oxide particles during sintering. The oxides hamper the densification process and result in decreased sintered density. Moreover, their existence reduces the Mn and Si dissolving into the base metal and compromises the solution strengthening effect. The oxides lead to stress concentration in the tensile and fatigue tests and become the initiation sites of fatigue cracks. After sintering, the samples made from the gas-atomized powder have a much lower oxygen content compared to those made from the water-atomized powder, therefore, exhibiting much better mechanical properties. The tensile strength, yield strength and the elongation of the samples made from the gas-atomized powder are 560 MPa, 205 MPa, and 58%, respectively. Their fatigue lives are about one order of magnitude longer than the samples made from water-atomized powder, and also longer than those fabricated by powder metallurgy and selective laser sintering which were reported in other studies.

Effects of Water Jet Peening and Hardening Treatment on Fatigue Properties of SCr420

2009 ◽  
Author(s):  
Akira Shimamoto ◽  
Ryo Kubota ◽  
Sung-mo Yang ◽  
Dae-kue Choi ◽  
Weiping Jia
Keyword(s):  
Fatigue Life ◽  
High Speed ◽  
Fatigue Crack Initiation ◽  
Fatigue Tests ◽  
Water Jet ◽  
Fatigue Properties ◽  
In Situ Observation ◽  
Axial Tensile ◽  
High Pressure Water Jet

An experimental study of high pressure water jet peening treatment on chromium steal SCr420 H3V2L2 is conducted to study the effects of cavitation impacts of high-speed water on fatigue crack initiation and propagation of notched specimens. There are six different kinds of specimens. First three kinds are treated with; only annealing, only water quenching, and only oil quenching. Other three kinds are treated with above heat treatment and water jet peening, respectively. An axial tensile fatigue tests’ condition is 260MPa maximum stress amplitude, 0 stress ratio and 10Hz frequency, while in-situ observation by SEM is employed. Although fatigue life of the specimens with annealing and water jet peening is shorter than that of only annealing, fatigue life of water and oil quenching with water jet peening specimens is obviously longer than those without water jet peening treatment. Water jet peening has increased residual stress inside the specimens on the latter case and raised their fatigue strength. In-situ observation on the crack tips approves above analysis.

Investigation of Residual Stresses in a Sleeve Coldworked Lug Specimen by Neutron and X-ray Diffraction

1994 ◽  
Vol 38 ◽  
pp. 455-461
Author(s):  
R. Lin ◽  
B. Jaensson ◽  
T. M. Holden ◽  
R. B. Rogge ◽  
J. H. Root
Keyword(s):  
Fatigue Life ◽  
Residual Stresses ◽  
Fatigue Cracks ◽  
Fatigue Properties ◽  
Aircraft Industry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Initiation And Propagation ◽  
Structural Parts ◽  
Compressive Residual Stresses

Sleeve coldworking (SCW) is a mechanical process used in the aircraft industry to strengthen fastener holes of structural parts. By cold-expanding the holes, compressive residual stresses and a high dislocation density are introduced around the holes, the effect of which is to counteract the initiation and propagation of fatigue cracks and thus increase the fatigue life of the parts. The knowledge of residual stress due to SCW is therefore crucial for assessing the fatigue properties of a treated part. In this study, residual stresses were investigated, by employing neutron and X-ray diffraction methods, in a lug specimen that was sleeve coldworked and fatigued. The specimen had been used for testing the influence of the SCW process on fatigue life and crack propagation behaviour under constant amplitude or variable amplitude cyclic loading.

scholarly journals Effect of UV Ageing on the fatigue life of bulk polyethylene

2018 ◽  
Vol 165 ◽  
pp. 08002 ◽  
Author(s):  
Hamza Lamnii ◽  
Moussa Nait-Abdelaziz ◽  
Georges Ayoub ◽  
Jean-Michel Gloaguen ◽  
Ulrich Maschke ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Uv Irradiation ◽  
Chemical Structure ◽  
Fatigue Behavior ◽  
Crystalline Polymer ◽  
Fatigue Loading ◽  
Chain Scission ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Irradiation Effect

Polymers operating in various weathering conditions must be assessed for lifetime performance. Particularly, ultraviolet (UV) radiations alters the chemical structure and therefore affect the mechanical and fatigue properties. The UV irradiation alters the polymer chemical structure, which results into a degradation of the mechanical and fatigue behavior of the polymer. The polymer properties degradation due to UV irradiation is the result of a competitive process of chain scission versus post-crosslinking. Although few studied investigated the effect of UV irradiation on the mechanical behaviour of thermoplastics, fewer examined the UV irradiation effect on the fatigue life of polymers. This study focuses on investigating the effect of UV irradiation on the fatigue properties of bulk semi-crystalline polymer; the low density Polyethylene (LDPE). Tensile specimens were exposed to different dose values of UV irradiation then subjected to fatigue loading. The fatigue tests were achieved under constant stress amplitude at a frequency of 1Hz. The results show an important decrease of the fatigue limit with increasing absorbed UV irradiation dose.

Sign in / Sign up

Export Citation Format

Share Document