Investigation of Formation Features of Sulphide Inclusions and their Distribution inside the Grain Depending upon the Conditions of Steel 20 Deoxidation

2019 ◽  
Vol 945 ◽  
pp. 592-597
Author(s):  
S.B. Gamanyuk ◽  
M.V. Kirilichev ◽  
G.V. Babin
Keyword(s):  
Oxygen Content ◽  
Plastic Properties ◽  
Oxidation Level ◽  
Metallic Inclusions ◽  
Distribution Features ◽  
Steel Oxidation ◽  
Negative Effect ◽  
Steel 20 ◽  
The Impact ◽  
Inclusions In Steel

The paper reports laboratory test findings on the impact of steel oxidation level on distribution features of non-metallic inclusions in low-alloyed structural steels. An analysis of the effect of various oxidation methods of steel on the distribution and formation of non-metallic inclusions is made. The results reveal a relation between the amount of sulphide and oxisulphide inclusions formed and steel oxidation level. The release of oxisulphide from the melt is accompanied with a decrease in the amount of both oxygen and sulphur. After oxygen content has achieved an equilibrium value, only “pure” sulphides are formed, which may deteriorate steel plastic properties. Thus, sulphides start precipitating only when oxygen content in the melt falls to a very low value. An increase in the amount of oxysulphides is accompanied with a decrease in sulphur concentration in the melt which reduces sulphide phase concentration at grain boundaries and stabilizes plastic properties. Thus the negative effect of sulphur can be reduced not only by decreasing its content in steel through expensive secondary steelmaking methods but also by controling the amount, shape and types of oxide, sulphide and oxisulphide inclusions in steel.

Secondary Steel Refining for Continuous Sequence Bloom Casting for High Oxide Cleanness Final Products

2012 ◽  
Vol 57 (1) ◽  
pp. 347-353 ◽  
Author(s):  
B. Zdonek ◽  
I. Szypuła ◽  
J. Kozłowski ◽  
S. Szczęch
Keyword(s):  
Continuous Casting ◽  
Oxygen Content ◽  
Equivalent Diameter ◽  
Process Technology ◽  
Total Oxygen ◽  
Total Oxygen Content ◽  
Continuous Sequence ◽  
Metallic Inclusions ◽  
Steel Refining ◽  
Inclusions In Steel

Secondary Steel Refining for Continuous Sequence Bloom Casting for High Oxide Cleanness Final ProductsSteelmaking and secondary refining process technology of resulphurized liquid steel with low content of total oxygen, assigned for continuous casting of strands for rolled and forged products for automotive industry was developed. The influence of secondary steel refining parameters on total oxygen content as well as amount and morphology of non-metallic inclusions was examined. It was found, that content of total oxygen and amount of non-metallic inclusions in steel decrease as steel refining time in the ladle becomes longer, and the chemical composition of non-metallic inclusions in steel changes from modified calcium aluminates to spinel inclusion of CaO·Al2O3·MgO type. The total oxygen content in steel from continuous casting in four cast sequence ranged from 6 to 25 ppm, with percentage share of non-metallic inclusions from 0.09 to 0.30 per cent and equivalent diameter 0.78 to 1.59 μm.

scholarly journals IMPACT OF CAST SPEED ON THE OCCURRENCE OF THE NON-METALLIC INCLUSIONS IN STEEL

2016 ◽  
Vol 22 (1) ◽  
pp. 4
Author(s):  
Vladimír Rega ◽  
Marek Molnár ◽  
Martin Jusko ◽  
Branislav Buľko ◽  
Jozef Kijac ◽  
...  
Keyword(s):  
Continuous Casting Machine ◽  
Casting Machine ◽  
Atomic Emission ◽  
Light Emitting ◽  
Metallic Inclusions ◽  
Steel Cast ◽  
The Individual ◽  
The Impact ◽  
Inclusions In Steel ◽  
The Given

<p>This paper deals with the examination of the impact of steel cast speed on the occurrence of the non-metallic inclusions due to the investigation of the individual samples taken at different steel cast speeds. The aim of this paper was to identify and describe the relation between the non-metallic inclusions occurring in the metal and the cast speed variations at the continuous casting machine. The non-metallic inclusions within this investigation were identified by the method (AES) based on the atomic emission spectroscopy that evaluates the occurrence of the determined elements in the metal. This method applies the principle of the light emitting acquired by the high-voltage spark supply. The investigation of the impact of both the technological production parameters, and the casting on the cleanliness of the given absorption quality of steel leads to their optimization, as well as, to total minimization of occurrence of the non-metallic inclusions in the steel volume were studied.</p>

scholarly journals Wide – Ranging Influence of Mischmetal on Properties of GP240GH Cast Steel

2012 ◽  
Vol 12 (4) ◽  
pp. 85-94
Author(s):  
J. Kasińska ◽  
M. Gajewski
Keyword(s):  
Rare Earth ◽  
Impact Strength ◽  
Cast Steel ◽  
Rare Earth Metals ◽  
Plastic Properties ◽  
Metallic Inclusions ◽  
Inclusion Morphology ◽  
Three Point Bend Test ◽  
Point Bend ◽  
The Impact

Abstract This paper presents influence of rare earth metals (REM) on the properties of GP240GH cast carbon steel. The research has been performed on successive industrial melts. Each time ca 2000 kg of liquid metal was modified. The rare earth metals were put into the ladle during tapping of heat melt from the furnace. Because of this the amount of sulphur in the cast steel was decreased and the non-metallic inclusion morphology was significantly changed. It was found that non metallic inclusions the cracking mechanism of Charpy specimens and the impact strength were all changed. The following properties were tested: mechanical properties (σy, σUTS), plastic properties (necking, elongation) and impact strength (SCI). In the three-point bend test the KJC stress intensity factor was evaluated.

The Transnational Women's Rights Movement and the World Economy

2020 ◽  
Vol 6 (2) ◽  
pp. 145-173 ◽  
Author(s):  
Heidi E. Rademacher
Keyword(s):  
Women's Rights ◽  
Small Body ◽  
World System ◽  
World Society ◽  
Women’S Rights ◽  
Social Movement Organizations ◽  
Global Movement ◽  
Negative Effect ◽  
Society Perspective ◽  
The Impact

Promoting the ratification of the Convention on the Elimination of All Forms of Discrimination against Women (CEDAW) was a key objective of the transnational women's movement of the 1980s and 1990s. Yet, few studies examine what factors contribute to ratification. The small body of literature on this topic comes from a world-society perspective, which suggests that CEDAW represented a global shift toward women's rights and that ratification increased as international NGOs proliferated. However, this framing fails to consider whether diffusion varies in a stratified world-system. I combine world-society and world-systems approaches, adding to the literature by examining the impact of women's and human rights transnational social movement organizations on CEDAW ratification at varied world-system positions. The findings illustrate the complex strengths and limitations of a global movement, with such organizations having a negative effect on ratification among core nations, a positive effect in the semiperiphery, and no effect among periphery nations. This suggests that the impact of mobilization was neither a universal application of global scripts nor simply representative of the broad domination of core nations, but a complex and diverse result of civil society actors embedded in a politically stratified world.

The Impact of Competitive Quasi-Market on Service Delivery in Benue State University, Makurdi Nigeria

GIS Business ◽  
2019 ◽  
Vol 14 (4) ◽  
pp. 85-98
Author(s):  
Idoko Peter
Keyword(s):  
Service Delivery ◽  
A Priori ◽  
Least Square ◽  
Secondary Source ◽  
State University ◽  
Ordinary Least Square ◽  
Negative Effect ◽  
The Impact ◽  
The Relationship

This research the impact of competitive quasi market on service delivery in Benue State University, Makurdi Nigeria. Both primary and secondary source of data and information were used for the study and questionnaire was used to extract information from the purposively selected respondents. The population for this study is one hundred and seventy three (173) administrative staff of Benue State University selected at random. The statistical tools employed was the classical ordinary least square (OLS) and the probability value of the estimates was used to tests hypotheses of the study. The result of the study indicates that a positive relationship exist between Competitive quasi marketing in Benue State University, Makurdi Nigeria (CQM) and Transparency in the service delivery (TRSP) and the relationship is statistically significant (p<0.05). Competitive quasi marketing (CQM) has a negative effect on Observe Competence in Benue State University, Makurdi Nigeria (OBCP) and the relationship is not statistically significant (p>0.05). Competitive quasi marketing (CQM) has a positive effect on Innovation in Benue State University, Makurdi Nigeria (INVO) and the relationship is statistically significant (p<0.05) and in line with a priori expectation. This means that a unit increases in Competitive quasi marketing (CQM) will result to a corresponding increase in innovation in Benue State University, Makurdi Nigeria (INVO) by a margin of 22.5%. It was concluded that government monopoly in the provision of certain types of services has greatly affected the quality of service experience in the institution. It was recommended among others that the stakeholders in the market has to be transparent so that the system will be productive to serve the society effectively

Problems of Implementation of an Import Substitution Policy in the Oil Industry

2019 ◽  
pp. 50-57
Author(s):  
Yu. V. Vertakova ◽  
A. S. Evtyukhin
Keyword(s):  
Import Substitution ◽  
Oil Industry ◽  
Investment Climate ◽  
Scientific Publications ◽  
Stage Of Development ◽  
Current Economic Situation ◽  
Negative Effect ◽  
Substitution Policy ◽  
Investment Process ◽  
The Impact

The presented study addresses the issues of implementation of an import substitution policy in the Russian oil industry. Support of domestic production is a key objective specified in the message of the President of the Russian Federation in 2019. In light of the current economic situation and considering the importance of the oil industry for the Russian economy, an import substitution policy could help achieve the objective set by the President.Aim. The study aims to identify the problems and ways of implementation of an import substitution policy in the Russian oil industry.Tasks. The authors analyze scientific publications on import substitution and the state of the Russian oil industry at the current stage of development; determine the directions and fundamental trends in the development of the oil industry; identify obstacles that hinder the implementation of an import substitution policy in the oil industry; describe conditions that facilitate the development of the  investment process in the oil industry; propose comprehensive methods and ways to intensify investments and optimize costs for enterprises in the oil industry.Methods. This study uses general scientific methods of cognition, comparative and statistical analysis to identify problems in the implementation of an import substitution policy in the oil industry.Results. Examination of the current state and development prospects of the oil industry allows the authors to identify obstacles to the development of import substitution. The study shows their impact on the potential of import substitution, which has a negative effect on the prospects of intensification of investment processes, and proposes comprehensive methods and mechanisms that could neutralize the impact of the identified obstacles, thus facilitating the formation of a positive investment climate. Conclusions. Investment climate is shown to have a decisive impact on the potential of import substitution in the Russian oil industry, and ways of overcoming negative trends in the development of the oil industry are proposed.

Others' participation rate influences an individual's charitable behavior: Others' similarity as a moderator

2017 ◽  
Vol 45 (10) ◽  
pp. 1607-1618 ◽  
Author(s):  
Seung Yun Lee ◽  
Sunho Jung ◽  
Sangdo Oh ◽  
Seong Hoon Park
Keyword(s):  
Undergraduate Students ◽  
Participation Rate ◽  
High Rate ◽  
Charitable Behavior ◽  
High Participation ◽  
Negative Effect ◽  
The Impact ◽  
And Diffusion ◽  
High Participation Rate ◽  
Diffusion Of Responsibility

We proposed that a moderator, others' similarity, would determine the impact of high participation rates of others on an individual's charitable behavior, and aimed to show that this moderator would work through the diffusion of responsibility motive. Participants (N = 152 undergraduate students) completed measures of charitable behavior and diffusion of responsibility, after being assigned to 1 of 2 conditions where a set percentage of other students (manipulated as either similar undergraduate students or dissimilar graduate students) were stated to have already donated to a charitable campaign (high contribution condition = 70% participation, low contribution condition = 30% participation). Our results showed that the high participation rate of others increased an individual's charitable behavior when the others in question were similar to that individual, but not when the others were dissimilar. In addition, the high rate of participation by others increased the diffusion of responsibility motive when the others in question were dissimilar to that individual, leading to a negative effect on that individual's charitable behavior.

scholarly journals Effect of Competition and Climatic Conditions on the Growth of Beech in the Mixed Pine Beech Stand: Lithuanian Case Study

2020 ◽  
Vol 3 (1) ◽  
pp. 49
Author(s):  
Edgaras Linkevičius ◽  
Gerda Junevičiūtė
Keyword(s):  
Intraspecific Competition ◽  
Tree Species ◽  
Forest Growth ◽  
Competition Effect ◽  
Diameter Increment ◽  
Cart Analysis ◽  
Crown Width ◽  
Beech Stand ◽  
Negative Effect ◽  
The Impact

Climate change and warming will potentially have profound effects on forest growth and yield, especially for pure stands in the near future. Thus, increased attention has been paid to mixed stands, e.g., pine and beech mixtures. However, the interaction of tree species growing in mixtures still remains unknown. Thus, the aim of this study was to investigate the impact of the interspecific and intraspecific competition to diameter, height, and crown width of pine and beech trees growing in mixtures, as well as to evaluate the impact of climatic indicators to the beech radial diameter increment. The data was collected in 2017 at the mixed mature pine beech double layer stand, located in the western part of Lithuania. The sample plot of 1.2 hectare was established and tree species, diameter at the breast height, tree height, height-to-crown base, height-to-crown width, and position were measured for all 836 trees. Additionally, a representative sample of radial diameter increments were estimated only for the beech trees by taking out core discs at the height of 1 m when the stand was partially cut. Competition analysis was based on the distance-dependent competition index, which was further based on crown parameters. Climatic effect was evaluated using classification and regression tree (CART) analysis. We found almost no interspecific competition effect to diameter, height, or crown width for both tree species growing in the first layer. However, it had an effect on beeches growing in the second layer. The intraspecific competition effect was important for pine and beech trees, showing a negative effect for both of them. Our results show the possible coexistence of these tree species due to niche differentiation. An analysis of climatic indicators from 1991–2005 revealed that precipitation from February–May of the current vegetation year and mean temperatures from July to September expressed radial diameter increment effects for beech trees. Low temperatures during March and April, as well as high precipitation during January, had a negative effect on beech radial increments. From 2006–2016, the highest effect on radial diameter increments was the mean temperatures from July to September, as well as the precipitation in January of the current year. From 1991–2016, the highest effect on radial diameter increments was the temperature from July to September 1991–2016 and the precipitation in June 1991–2016. Generally, cool temperatures and higher precipitation in June had a positive effect on beech radial increments. Therefore, our results show a sensitivity to high temperatures and droughts during summer amid Lithuanian’s growth conditions.

scholarly journals The Impact of Urban Recreation Environment on Residents’ Happiness—Based on a Case Study in China

2021 ◽  
Vol 13 (10) ◽  
pp. 5549
Author(s):  
Lei Kang ◽  
Zhaoping Yang ◽  
Fang Han
Keyword(s):  
Low Income ◽  
Subjective Evaluation ◽  
Objective Evaluation ◽  
Income Group ◽  
High Income Group ◽  
Rapid Urbanization ◽  
Indirect Impact ◽  
Negative Effect ◽  
The Impact ◽  
Urban Recreation

Rapid urbanization promotes the expansion of urban tourism and recreation functions, but it also brings many problems, which affect residents’ happiness. Previous studies have emphasized the direct impact of urban recreation environment on happiness, and few have explored the indirect impact of urban recreation environment on happiness through subjective evaluation. Based on the survey data of nearly 10,000 permanent residents in 40 key tourism cities in China, this paper establishes a theoretical framework of the direct and indirect impact of urban recreation environment on happiness. The objective evaluation of natural recreation environment and sociocultural recreation environment has an important influence on happiness, but the influence of natural recreation environment is greater than that of sociocultural recreation environment. Individual subjective satisfaction with urban recreation environment mediates the relationship between urban objective environment and happiness. Urban parks have a positive effect on happiness, while tourist attractions have a negative effect. The influence of urban location on happiness is nonlinear. The high-income group is more sensitive to the recreation environment, while the low-income group is less sensitive to the recreation environment. These findings provide insights for further improving citizens’ quality of life and designing urban construction in developing countries under the conditions of rapid urbanization.

scholarly journals The Impact of Health Policies and Sociodemographic Factors on Doubling Time of the COVID-19 Pandemic in Mexico

2021 ◽  
Vol 18 (5) ◽  
pp. 2354
Author(s):  
Lina Díaz-Castro ◽  
Héctor Cabello-Rangel ◽  
Kurt Hoffman
Keyword(s):  
Population Density ◽  
Doubling Time ◽  
Sociodemographic Factors ◽  
Health Policies ◽  
Government Response ◽  
University Of Oxford ◽  
Negative Effect ◽  
Population Sizes ◽  
The University ◽  
The Impact

Background. The doubling time is the best indicator of the course of the current COVID-19 pandemic. The aim of the present investigation was to determine the impact of policies and several sociodemographic factors on the COVID-19 doubling time in Mexico. Methods. A retrospective longitudinal study was carried out across March–August, 2020. Policies issued by each of the 32 Mexican states during each week of this period were classified according to the University of Oxford Coronavirus Government Response Tracker (OxCGRT), and the doubling time of COVID-19 cases was calculated. Additionally, variables such as population size and density, poverty and mobility were included. A panel data model was applied to measure the effect of these variables on doubling time. Results. States with larger population sizes issued a larger number of policies. Delay in the issuance of policies was associated with accelerated propagation. The policy index (coefficient 0.60, p < 0.01) and the income per capita (coefficient 3.36, p < 0.01) had a positive effect on doubling time; by contrast, the population density (coefficient −0.012, p < 0.05), the mobility in parks (coefficient −1.10, p < 0.01) and the residential mobility (coefficient −4.14, p < 0.01) had a negative effect. Conclusions. Health policies had an effect on slowing the pandemic’s propagation, but population density and mobility played a fundamental role. Therefore, it is necessary to implement policies that consider these variables.

Sign in / Sign up

Export Citation Format

Share Document