scholarly journals Chemical Composition of Clays for Pottery in Malaysia: A Review

2021 ◽  
Vol 3 (1) ◽  
pp. 144-153
Author(s):  
N.A. Gani ◽  
M.S. Shamsuddin ◽  
W.K. Koo ◽  
M.N. Masri ◽  
M.A. Sulaiman
Keyword(s):  
Major Element ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Chemical Properties ◽  
Chemical Compositions ◽  
Oxide Compound ◽  
Product Increase ◽  
Quality And Reliability ◽  
Increase Alumina Content ◽  
And Chemical Properties

Pottery in Malaysia is been known for its utilized functions and unique properties. Clays as the pottery’s raw materials are a major factor that affecting the quality and reliability of some pottery products. Observations on clays’ elements and phases are very helpful for productions of the good pottery. Hence, in this review, chemical compositions of clays in terms of elements and phases structures are discussed. Basically, the most elements found in clays are Si, Al, Fe, Ti, K and Ca. Depends on location, the concentrations for those clays elements in Malaysia are at range of 24.8 – 32.4 for Si, 10.8 – 19.0 for Al, 0.09 – 2.12 for Fe, 0.08 – 1.13 for Ti and 0.45 – 3.39 for K. Several studies reported, they exist in form of oxide compound which are SiO2, Al2O3, Fe2O3, TiO2, MgO, CaO, Na2O, K2O and P2O5. The percentages of elements in clays do not only determine the clays characteristics, but also influence the physical, mechanical and chemical properties of the end product. Increase of major element like silica arises the melting point, lowers the fluidity, and enhances the hardness and tensile strength. Meanwhile, increase alumina content enables the green body to withstand the sintering temperature and also increase the hardness of the pottery.

Diesel Biofuels - Preparation, Characterization and Testing

2008 ◽  
Vol 59 (11) ◽  
Author(s):  
Cristina Dusescu ◽  
Anca Borcea ◽  
Vasile Matei ◽  
Ion Popa ◽  
Irina Gabriela Radulescu
Keyword(s):  
Vegetable Oils ◽  
Sunflower Oil ◽  
Raw Materials ◽  
Chemical Properties ◽  
Soya Bean ◽  
Production Unit ◽  
Physical And Chemical Properties ◽  
Physical And Chemical ◽  
And Chemical Properties

The present paper studies biodiesel samples preparation by transesterification and compares their physical and chemical properties (biofuels prepared from different raw materials - vegetable oils: sunflower oil, crocus oil and soya bean oil) and the biodegradability degree, as well as the possibilities of the integration of such production unit in industrial diagram of auto fuels production.

scholarly journals Eco-Compatible Construction Materials Containing Ceramic Sludge and Packaging Glass Cullet

2021 ◽  
Vol 11 (8) ◽  
pp. 3545
Author(s):  
Fernanda Andreola ◽  
Isabella Lancellotti ◽  
Paolo Pozzi ◽  
Luisa Barbieri
Keyword(s):  
Raw Materials ◽  
Construction Materials ◽  
Treatment Plant ◽  
Glass Ceramics ◽  
Chemical Properties ◽  
Linear Shrinkage ◽  
Glass Cullet ◽  
Commercial Glass ◽  
Packaging Glass ◽  
And Chemical Properties

This research reports results of eco-compatible building material obtained without natural raw materials. A mixture of sludge from a ceramic wastewater treatment plant and glass cullet from the urban collection was used to obtain high sintered products suitable to be used as covering floor/wall tiles in buildings. The fired samples were tested by water absorption, linear shrinkage, apparent density, and mechanical and chemical properties. Satisfactory results were achieved from densification properties and SEM/XRD analyses showed a compact polycrystalline microstructure with albite and wollastonite embedded in the glassy phase, similar to other commercial glass-ceramics. Besides, the products were obtained with a reduction of 200 °C with respect to the firing temperatures of commercial ones. Additionally, the realized materials were undergone to leaching test following Italian regulation to evaluate the mobility of hazardous ions present into the sludge. The data obtained verified that after thermal treatment the heavy metals were immobilized into the ceramic matrix without further environmental impact for the product use. The results of the research confirm that this valorization of matter using only residues produces glass ceramics high sintered suitable to be used as tile with technological properties similar or higher than commercial ones.

scholarly journals Mineralogical and chemical properties inversed from 21-lunar-day VNIS observations taken during the Chang’E-4 mission

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Qinghong Zeng ◽  
Shengbo Chen ◽  
Yuanzhi Zhang ◽  
Yongling Mu ◽  
Rui Dai ◽  
...  
Keyword(s):  
Impact Crater ◽  
Near Infrared ◽  
Infrared Imaging ◽  
Chemical Properties ◽  
Landing Site ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Chemical Compositions ◽  
Impact Melt ◽  
And Chemical Properties

AbstractWe report on the mineralogical and chemical properties of materials investigated by the lunar rover Yutu-2, which landed on the Von Kármán crater in the pre-Nectarian South Pole–Aitken (SPA) basin. Yutu-2 carried several scientific payloads, including the Visible and Near-infrared Imaging Spectrometer (VNIS), which is used for mineral identification, offering insights into lunar evolution. We used 86 valid VNIS data for 21 lunar days, with mineral abundance obtained using the Hapke radiative transfer model and sparse unmixing algorithm and chemical compositions empirically estimated. The mineralogical properties of the materials at the Chang’E-4 (CE-4) site referred to as norite/gabbro, based on findings of mineral abundance, indicate that they may be SPA impact melt components excavated by a surrounding impact crater. We find that CE-4 materials are dominated by plagioclase and pyroxene and feature little olivine, with 50 of 86 observations showing higher LCP than HCP in pyroxene. In view of the effects of space weathering, olivine content may be underestimated, with FeO and TiO2 content estimated using the maturity-corrected method. Estimates of chemical content are 7.42–18.82 wt% FeO and 1.48–2.1 wt% TiO2, with a low-medium Mg number (Mg # ~ 55). Olivine-rich materials are not present at the CE-4 landing site, based on the low-medium Mg #. Multi-origin materials at the CE-4 landing site were analyzed with regard to concentrations of FeO and TiO2 content, supporting our conclusion that the materials at CE-4 do not have a single source but rather are likely a mixture of SPA impact melt components excavated by surrounding impact crater and volcanic product ejecta.

The Extraction of Main Chemical Compositions in Rumex Root

2011 ◽  
Vol 382 ◽  
pp. 372-374
Author(s):  
Yong Jiang ◽  
Zhi Bin Jiang ◽  
Guo Jie Shao ◽  
Dong Cheng Guo ◽  
Yu Tian ◽  
...  
Keyword(s):  
Molecular Structure ◽  
Chemical Properties ◽  
Ethanol Extract ◽  
Chemical Compositions ◽  
Physical And Chemical Properties ◽  
Experimental Basis ◽  
Development And Utilization ◽  
Physical And Chemical ◽  
Root Methods ◽  
And Chemical Properties

Purpose: The purpose of this study was to study the compositions of the polygonaceae medicinal plants called rumex root. Methods: Solvent method and chromatography was used to purificate the chemical compositions of Rumex, and the molecular structure of the compound was identified by physical and chemical properties and spectral data. Results: Two compounds were obtained from the ethanol extract of rumex root, which were identified as Chrysophanol and Physcione. Conclusions: Experimental basis was provided for the further study of the active ingredients of rumex root and the development and utilization of medical resources.

scholarly journals Study of the Incorporation of Biomass Bottom Ash as a Filler for Discontinuous Grading Bituminous Mixtures with Bitumen Emulsion

2021 ◽  
Vol 11 (8) ◽  
pp. 3334
Author(s):  
Jorge Suárez-Macías ◽  
Juan María Terrones-Saeta ◽  
Francisco Javier Iglesias-Godino ◽  
Francisco Antonio Corpas-Iglesias
Keyword(s):  
Raw Materials ◽  
Bottom Ash ◽  
Chemical Properties ◽  
Physical And Mechanical Properties ◽  
Waste Biomass ◽  
Bituminous Mixtures ◽  
Bitumen Emulsion ◽  
Main Disadvantage ◽  
Physical And Chemical ◽  
And Chemical Properties

Energy consumption, because of population development, is progressively increasing. For this reason, new sources of energy are being developed, such as that produced from the combustion of biomass. However, this type of renewable energy has one main disadvantage, the production of waste. Biomass bottom ash is a residue of this industry that currently has not much use. For this reason, this research evaluates its use as a filler in bituminous mixtures, since this sector also has a significant impact on the environment, as it requires large quantities of raw materials. With this objective, first, the physical and chemical properties of biomass bottom ashes were evaluated, verifying their characteristics for their use as filler. Subsequently, bituminous mixtures were conformed with biomass bottom ash as filler, and their physical and mechanical properties were analyzed through particle loss and Marshall tests. The results of these tests were compared with those obtained with the same type of mixture but with conventional and ophite aggregates. This study confirmed that biomass bottom ash was viable for use as a filler, creating mixtures with a higher percentage of bitumen, better mechanical behavior, and similar physical properties. In short, more sustainable material for roads was obtained with waste currently condemned to landfill.

scholarly journals Investigation of Microbial Contamination and Physicochemical Properties of Compounded Medications in Pharmacies

2020 ◽  
Vol 26 (1) ◽  
pp. 82-93
Author(s):  
Reihaneh Radmanesh ◽  
◽  
Mohsen Nabi Meybodi ◽  
Vahid Ramezani ◽  
Maryam Akrami ◽  
...  
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Microbial Contamination ◽  
Raw Materials ◽  
Chemical Properties ◽  
Pharmaceutical Product ◽  
Physical And Chemical ◽  
Made In ◽  
And Chemical Properties

Aims: Any pharmaceutical product made in pharmacy, hospital or factory may be contaminated with microbes. This contamination can originate from raw materials or during production. Hence, it is important to study the physical and chemical properties and stability of compounded drugs. Methods & Materials: In this study, first a specific sample of prescribed medication was ordered from 63 pharmacies in Yazd, Iran. After collecting the samples, the amount of microbial contamination, viscosity and particle size distribution and their stability were investigated and their results were compared to the standard levels. Findings: Based on the results, 31.7% of the samples had discoloration and 23.8% showed creaming phenomenon. In terms of particle size distribution, 57.1% of the samples had a 20-40 μm particle size and 49.2% had a viscosity equal to 2500-3000 centipoise. Regarding stability, 12.6% of the samples underwnet phase change at 30-40°C. About of the amount of hydroquinone in samples, 35% had acceptable amount. In 23.8% of the samples, fungal infection was observed. Conclusion: Contrary to a popular belief that the compounded medicines produced in pharmacies have microbial contamination, the results of this study showed that the microbial contamination of these compounded medications is low.

scholarly journals Influence of temperature regimes of ripening and fermentation stages on the physical and chemical properties of cream and sour-cream butter quality indicators

2018 ◽  
Vol 12 (3) ◽  
Author(s):  
O. O. Bondarchuk
Keyword(s):  
Milk Fat ◽  
Raw Materials ◽  
Chemical Properties ◽  
Physical And Chemical Properties ◽  
Second Stage ◽  
Temperature Regimes ◽  
Third Stage ◽  
Sour Cream ◽  
Physical And Chemical ◽  
And Chemical Properties

Physical and chemical properties of cream multistep modes of ripening and fermentations are investigation and their role in the production of sour-cream butter is studied. The process of ripening of cream was carried out multistep, regimes were selected depending on seasonal changes in the composition of milk fat. For raw materials of the autumn-winter period, for the values of iodine number 29.1–34.5, the first stage of ripening was carried out at a temperature of 8°C for 2 hours, the second stage – at 21°C for 7 hours, the third stage – at 13°C for 10 hours. For raw of spring-summer period, for the values of iodine number 34.5–40.1, the first stage of ripening was carried out at 21°C for 6 hours, the second stage – at 13°C for 4 hours, the third stage – at 8°C for 8 hours. It has been established that individual modes of low-temperature cream preparation, taking into account seasonal changes in the composition of milk fat, make it possible to obtain cream before churning almost with the same indexes of effective viscosity. The content of the crystalline phase of milk fat under both temperature regimes was 38.7–40.1%, which is sufficient to obtain of proper consistency sour-cream butter. The content of diacetyl and volatile organic acids more depend on the level of fermentation of cream than on the technological regimes of ripening and seasonality of raw materials. It has been proved that an increase in the fermentation degree of cream promotes an increase in the acidity of plasma and the content of aroma-producing components in the butter, and, accordingly, affects the degree of the sour taste. It is recommended for the production of cultured butter to begin the cream when the acidity of the plasma reaches 60ºT, which ensures the formation of high sensorial characteristic of the finished product.

Vegetable oils – raw materials for producing biodiesel

2021 ◽  
Vol 80 (2) ◽  
pp. 286-292
Author(s):  
T. Mamilov ◽  
◽  
G.S. Aitkaliyeva ◽  
A.B. Ismailova ◽  
M.A. Yelubay ◽  
...  
Keyword(s):  
Functional Groups ◽  
Vegetable Oils ◽  
Raw Materials ◽  
Chemical Properties ◽  
Biodiesel Fuel ◽  
Physical And Chemical Properties ◽  
Sunflower Oils ◽  
Transesterification Method ◽  
Physical And Chemical ◽  
And Chemical Properties

This paper presents the results of a study of the physical and chemical properties of samples of vegetable oils (sunflower, rapeseed, olive). It has been shown that the viscosity of oils varies from 41.4 to 61.7 cSt at a temperature of 40 ° C for olive and sunflower oils, respectively. The acid numbers of the oil samples were also determined, it was found that the lowest indicator is characteristic of sunflower oil. Pour points of oils also range from -3 to -16 ° C for olive and sunflower oils, respectively. Using the method of IR spectroscopy, functional groups in the composition of samples of vegetable oils were studied and it was shown that the composition of oils contains carbonyl and hydroxyl functional groups, indicating the presence of carboxylic acids. Based on studies of the physical and chemical properties of vegetable oils, it was found that sunflower, olive and rapeseed oils can serve as raw materials for the synthesis of biofuels based on them, since they contain free fatty acids. To obtain biodiesel fuel based on vegetable oils, it is planned to use the transesterification method in the presence of various catalysts (alkaline, acidic, and complex).

Microporous Ceramics Made by Silicon Carbide Whiskers

2007 ◽  
Vol 336-338 ◽  
pp. 1904-1905
Author(s):  
Chang Hong Dai ◽  
Ru Zhao ◽  
Li Shui ◽  
Bao Bao Zhang
Keyword(s):  
Silicon Carbide ◽  
Flexural Strength ◽  
Pore Size ◽  
Sintering Temperature ◽  
Chemical Properties ◽  
Physical And Chemical Properties ◽  
Sintering Aids ◽  
Silicon Carbide Whiskers ◽  
Physical And Chemical ◽  
And Chemical Properties

A new method for preparing microporous ceramics by the silicon carbide whiskers was studied in this paper. The physical and chemical properties and the microstructure of the microporous ceramics were tested, while some influencing factors for the product, such as the amount of sintering aids and sintering temperature, were discussed. The results suggest that the apparent porosity of the microporous ceramics is 55.7-59.8% and the flexural strength is 127-176MPa. The pore distribution of the microporous ceramics is uniformity and the diameter of the pore ranges between 0.5μm and 7μm. The porosity and pore size of the microporous ceramic can be controlled by adjusting the sintering temperature and the amount of sintering aids.

Sign in / Sign up

Export Citation Format

Share Document