scholarly journals LOW TEMPERATURE DEGRADATION BEHAVIOUR OF 10Ce-TZP/Al2O3 BIOCERAMICS OBTAINED BY MICROWAVE SINTERING TECHNOLOGY

2019 ◽  
Author(s):  
Lorena Gil-Flores ◽  
María D Salvador ◽  
Felipe L Penaranda-Foix ◽  
Roberto Rosa ◽  
Paolo Veronesi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Microwave Heating ◽  
Biomedical Applications ◽  
Microwave Sintering ◽  
Hydrothermal Aging ◽  
Degradation Behaviour ◽  
Al2o3 Composite ◽  
Heating Technology ◽  
Spontaneous Phase

Zirconia is one of the most used ceramics, especially for biomedical applications, due to its exceptional mechanical properties. However, it is commonly known that its properties can be diminished owing to a low temperature degradation (LTD). This phenomenon consists on a spontaneous phase transformation, from tetragonal to monoclinic, under certain conditions, which is accelerated when the samples are exposed under high levels of humidity at a temperature range between 20-300 ºC. In addition to the fact that the monoclinic phase presents worse mechanical properties than the tetragonal one, there is a volume change of 4% between phases that gives rise to defects in the material as microcracks. Due to this reason, zirconia prostheses failed catastrophically inside the human body between 1999 and 20011. Previous researches reveal that Al2O3 addition suppress the propagation of phase transformation2. Thus, the aim of the present work is to study the hydrothermal ageing of zirconia doped with ceria and toughened with alumina (10Ce-TZP/Al2O3) composite, which has been sintered by microwave employing two different frequencies: 2.45 and 5.8 GHz. Microwave heating technology is based on the absorption of electromagnetic radiation by the material, which allows the sample to be heated. So far, most microwave heating equipments use 2.45 GHz; accordingly, the novelty of this study is to employ a frequency of 5.8 GHz and to investigate its effect on LTD. LTD is carried out in an autoclaved in steam at 120 ºC and 1.2 bar, because these conditions accelerate the hydrothermal aging process3. In order to characterize the degraded samples, micro-Raman spectroscopy, AFM, nanoindentation technique and electronic microscopy have been performed.   References 1.           Norton, M. R., Yarlagadda, R., Anderson, G. H. J. Bone Joint Surg. Br., 2002, 84–B, 631–635. 2.           Fabbri, P., Piconi, C., Burresi, E., Magnani, G., Mazzanti, F., Mingazzini, C. Dent. Mater., 2014. 3.           Presenda, Á., Salvador, M. D., Moreno, R., Borrell, A. J. Am. Ceram. Soc., 2015, 98, 3680–3689.   

Preparation of WC-TiC-Ni3Al-CaF2 functionally graded self-lubricating tool material by microwave sintering and its cutting performance

2020 ◽  
Vol 39 (1) ◽  
pp. 45-53 ◽  
Author(s):  
Siwen Tang ◽  
Rui Wang ◽  
Pengfei Liu ◽  
Qiulin Niu ◽  
Guoqing Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Microwave Heating ◽  
Cutting Performance ◽  
Conventional Heating ◽  
Hard Alloys ◽  
Dry Cutting ◽  
Temperature Oxidation ◽  
Lubricating Material ◽  
Heating Technology

AbstractWith the concern of the environment, green dry cutting technology is getting more and more attention and self-lubricating tool technology plays an important role in dry cutting. Due to the demand for high temperature performance of tools during dry cutting process, cemented carbide with Ni3Al as the binder phase has received extensive attention due to its excellent high temperature strength and high temperature oxidation resistance. In this paper, WC-TiC-Ni3Al-CaF2 graded self-lubricating material and tools were prepared by microwave heating method, and its microstructure, mechanical properties and cutting performance were studied. Results show that gradient self-lubricating material can be quickly prepared by microwave heating technology, and the strength is equivalent to that of conventional heating technology. CaF2 not only plays a role in self-lubrication, but also refines the grain of the material. A reasonable gradient design can improve the mechanical properties of the material. When the gradient distribution exponent is n1 = 2, the material has high mechanical properties. Cutting experiments show that the WC-TiC-Ni3Al-CaF2 functional gradient self-lubricating tool has better cutting performance than the homogeneous WC-TiC-Ni3Al hard alloys.

Experimental investigation and empirical modeling for corrosion rate prediction of biodegradable zinc based composite considering the effect of constituent materials

2021 ◽  
pp. 095440622110556
Author(s):  
Dayanidhi Krishana Pathak ◽  
Pulak Mohan Pandey
Keyword(s):  
Mechanical Properties ◽  
Corrosion Rate ◽  
Biomedical Applications ◽  
Microwave Sintering ◽  
Research Work ◽  
Simulated Body Fluid Solution ◽  
Corrosion Current ◽  
Essential Elements ◽  
Empirical Modeling ◽  
Corrosion Properties

Biodegradable zinc (Zn) has shown great potential in the area of biomedical applications. Though, the mechanical properties are decisive for the use of Zn for orthopedic and cardiovascular applications. Consequently, one needs to focus on improving the mechanical properties of Zn for its suitability in biomedical applications. Alloying of essential elements of the human body resulted in enhancement of Zn’s mechanical properties in recent years. The corrosion rate of pure Zn is ideal; however, the addition of other elements has resulted in a loss of its ideal corrosion rate. The inclusion of hydroxyapatite (HA) and iron (Fe) in Zn has also been reported in improving the mechanical properties. Hence, a need is raised for the development of a model which can predict the corrosion rate after adding HA along with Fe in Zn. In this research work, empirical based modeling is proposed to predict the corrosion rate, which incorporates the outcome of addition of Fe and HA in Zn. The Zn based materials were fabricated with the help of microwave sintering for developing the empirical model. The corrosion properties of the materials were assessed through a potentiodynamic polarization test in a simulated body fluid solution. The enhanced corrosion rate was attained with the rise in HA (wt%) and Fe (wt%) in Zn. An empirical correlation was established between the influencing controlling parameters (i.e., corrosion current, equivalent weight, and material density) of corrosion rate. Confirmation experiments were conducted to validate the developed model, and the highest error of 6.12% was obtained between the experimental and predicted values exhibiting the efficaciousness of the proposed model.

Microstructure and Mechanical Properties of Fe/MgO Micro-Nano Composite for Electrotechnical Applications

2018 ◽  
Vol 18 (2) ◽  
pp. 103-110
Author(s):  
R. Bureš ◽  
M. Fáberová ◽  
P. Kurek
Keyword(s):  
Mechanical Properties ◽  
Magnetic Properties ◽  
Flexural Strength ◽  
Microwave Heating ◽  
Microwave Sintering ◽  
Process Time ◽  
Nano Composite ◽  
Microstructure And Mechanical Properties ◽  
Sintering Method ◽  
Size Powder

Abstract The composite based on the microns iron size powder and MgO nanopowder was prepared using pressing followed by conventional and microwave sintering. Microstructure of the composite was investigated to evaluate the changes induced by different sintering technology. Young’s modulus, flexural strength and hardness of composites were analyzed to investigate the mechanical properties in dependence on MgO content, as well as in dependence on the sintering method. Microstructure and mechanical properties as well as functional magnetic properties of prepared composites are discussed in the paper. The main benefit of microwave heating found within process time shortening was confirmed in the case of the microwave sintered Fe/MgO composite.

Effect of SiCp Addition on Microstructure and Mechanical Properties of ZTA Ceramics by Microwave Sintering

2018 ◽  
Vol 281 ◽  
pp. 217-223 ◽  
Author(s):  
Yong Qiang Chen ◽  
Sai Li ◽  
Wei Li ◽  
Ting Ting Su ◽  
Bing Bing Fan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Microwave Heating ◽  
Bending Strength ◽  
Microwave Sintering ◽  
Precipitation Method ◽  
Stabilized Zirconia ◽  
Oriented Growth ◽  
Directional Growth ◽  
Partially Stabilized Zirconia ◽  
Microstructure And Mechanical Properties

The effects of SiCp addition on the microstructure and mechanical properties of ZTA ceramics was investigated by microwave sintering. Partially stabilized zirconia（3Y-ZrO2）nanopowder containing SiCp was prepared by microwave pyrolysing precursor which was was achieved by co-precipitation method. The powders of alumina, yttria partially stabilized zirconia containing SiCp were mixed to prepare ZTA ceramics green body by die pressing and cold isostatic pressing and subsequently sintered at the range of 1350°C-1550°C for 30min by microwave. XRD revealed that 3Y-ZrO2/SiC powder contained more tetragonal phase than 3Y-ZrO2 powder which was also confirmed by SEM and particle size distribution. The phenomenon was because of SiCp forming the microwave heating spot that promoted pyrolysis progress when 3Y-ZrO2/SiC powder was prepared by microwave heating. Microstructure showed that the grain of ZTA ceramics had directional growth by microwave sintering. SiCp firstly absorbed microwave that made more uniform sintering of ZTA ceramics and caused local oriented growth of zirconia and alumina. Thus, the bending strength of ZTA ceramics was higher than ZTA without SiCp. The ladder type heating mode of microwave sintering ZTA ceramics reduced relatively sintering time by 20min due to the addition of SiCp.Introduction

Research on the Pavement Performance of Recycled Asphalt Mixture Processed by Microwave

2010 ◽  
Vol 148-149 ◽  
pp. 987-993
Author(s):  
Song Qing Zhu ◽  
Jin Fei Shi ◽  
Fei Hao
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Microwave Heating ◽  
Fatigue Cracks ◽  
Asphalt Mixture ◽  
Microwave Processing ◽  
Bending Test ◽  
Conventional Heating ◽  
Pavement Performance ◽  
Recycled Asphalt

In order to evaluate the pavement performance of recycled asphalt mixture processed by microwave, an experimental method was designed to compare the microwave heating with the conventional heating in recycling affection of asphalt mixture. The samples AC-13 were produced. Conventional and microwave heating performance of modified asphalt recycling test including the rutting test, the trabecular cold bending test, the Marshall immersion test, the freeze-thaw split test, and the splitting strength mechanical properties were test. The experimental results show that it is roughly the same in the high temperature stability and mechanical properties of these two areas, and at low temperature cracking resistance the use of microwave processing can improve the low temperature flexibility to reduce the surface temperature seasonal prone temperature shrinkage cracks and fatigue cracks. The stability on the water by using microwave processing can enhance the asphalt and aggregate adhesion so that mixture enhanced resistance to water damage, there is a better role in improving the water stability. These results could promote microwave recycling and provide the basis for the promotion applications.

Usefulness of Foundry Tooling Materials in Microwave Heating Process

2013 ◽  
Vol 58 (3) ◽  
pp. 919-922 ◽  
Author(s):  
K. Granat ◽  
B. Opyd ◽  
D. Nowak ◽  
M. Stachowicz ◽  
G. Jaworski
Keyword(s):  
Electromagnetic Field ◽  
Microwave Heating ◽  
Loss Factor ◽  
Perturbation Technique ◽  
Resonant Cavity ◽  
Precise Determination ◽  
Heating Process ◽  
Basic Criterion ◽  
Measurement Results ◽  
Heating Technology

Abstract The paper describes preliminary examinations on establishing usefulness criteria of foundry tooling materials in the microwave heating technology. Presented are measurement results of permittivity and loss tangent that determine behaviour of the materials in electromagnetic field. The measurements were carried-out in a waveguide resonant cavity that permits precise determination the above-mentioned parameters by perturbation technique. Examined were five different materials designed for use in foundry tooling. Determined was the loss factor that permits evaluating usefulness of materials in microwave heating technology. It was demonstrated that the selected plastics meet the basic criterion that is transparency for electromagnetic radiation.

NIKROTHAL TE

Alloy Digest ◽  
2013 ◽  
Vol 62 (10) ◽  
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Tensile Properties ◽  
Turn Of The Century ◽  
Heating Element ◽  
Attractive Alternative ◽  
Electric Resistance ◽  
Household Appliances ◽  
Nickel Chromium ◽  
Heating Technology

Abstract NIKROTHAL TE is a member of the Nikrothal family of alloys, which are one of two main types of electric-resistance alloys. Nickel-chromium (80Ni-20Cr, for example), developed around the turn of the century, was used as heating-element material in industrial furnaces and electric household appliances. Nikrothal alloys offer advantages in heating-element applications requiring very good mechanical properties in the hot state. This alloy is an attractive alternative to Nikrothal Alloys 40, 60, 70, and 80 (see Alloy Digest Ni-529, September 1997). This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on forming. Filing Code: Ni-710. Producer or source: Sandvik Heating Technology.

Cellulose Nanofibrils-based Hydrogels for Biomedical Applications: Progresses and Challenges

2020 ◽  
Vol 27 (28) ◽  
pp. 4622-4646 ◽  
Author(s):  
Huayu Liu ◽  
Kun Liu ◽  
Xiao Han ◽  
Hongxiang Xie ◽  
Chuanling Si ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Metal Ion ◽  
Biomedical Applications ◽  
Biomedical Application ◽  
Cellulose Nanofibrils ◽  
Wound Dressings ◽  
Preparation Methods ◽  
Tissue Scaffold ◽  
Surface Areas ◽  
Mechanical Methods

Background: Cellulose Nanofibrils (CNFs) are natural nanomaterials with nanometer dimensions. Compared with ordinary cellulose, CNFs own good mechanical properties, large specific surface areas, high Young's modulus, strong hydrophilicity and other distinguishing characteristics, which make them widely used in many fields. This review aims to introduce the preparation of CNFs-based hydrogels and their recent biomedical application advances. Methods: By searching the recent literatures, we have summarized the preparation methods of CNFs, including mechanical methods and chemical mechanical methods, and also introduced the fabrication methods of CNFs-based hydrogels, including CNFs cross-linked with metal ion and with polymers. In addition, we have summarized the biomedical applications of CNFs-based hydrogels, including scaffold materials and wound dressings. Results: CNFs-based hydrogels are new types of materials that are non-toxic and display a certain mechanical strength. In the tissue scaffold application, they can provide a micro-environment for the damaged tissue to repair and regenerate it. In wound dressing applications, it can fit the wound surface and protect the wound from the external environment, thereby effectively promoting the healing of skin tissue. Conclusion: By summarizing the preparation and application of CNFs-based hydrogels, we have analyzed and forecasted their development trends. At present, the research of CNFs-based hydrogels is still in the laboratory stage. It needs further exploration to be applied in practice. The development of medical hydrogels with high mechanical properties and biocompatibility still poses significant challenges.

scholarly journals Dynamic Mechanical Control of Alginate-Fibronectin Hydrogels with Dual Crosslinking: Covalent and Ionic

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 433
Author(s):  
Sara Trujillo ◽  
Melanie Seow ◽  
Aline Lueckgen ◽  
Manuel Salmeron-Sanchez ◽  
Amaia Cipitria
Keyword(s):  
Mechanical Properties ◽  
Biomedical Applications ◽  
Divalent Cations ◽  
Dynamic Control ◽  
Dynamic Mechanical Properties ◽  
Full Length ◽  
Dynamic Mechanical ◽  
Covalent Crosslinking ◽  
Calcium Cations ◽  
Different Tissues

Alginate is a polysaccharide used extensively in biomedical applications due to its biocompatibility and suitability for hydrogel fabrication using mild reaction chemistries. Though alginate has commonly been crosslinked using divalent cations, covalent crosslinking chemistries have also been developed. Hydrogels with tuneable mechanical properties are required for many biomedical applications to mimic the stiffness of different tissues. Here, we present a strategy to engineer alginate hydrogels with tuneable mechanical properties by covalent crosslinking of a norbornene-modified alginate using ultraviolet (UV)-initiated thiol-ene chemistry. We also demonstrate that the system can be functionalised with cues such as full-length fibronectin and protease-degradable sequences. Finally, we take advantage of alginate’s ability to be crosslinked covalently and ionically to design dual crosslinked constructs enabling dynamic control of mechanical properties, with gels that undergo cycles of stiffening–softening by adding and quenching calcium cations. Overall, we present a versatile hydrogel with tuneable and dynamic mechanical properties, and incorporate cell-interactive features such as cell-mediated protease-induced degradability and full-length proteins, which may find applications in a variety of biomedical contexts.

Sign in / Sign up

Export Citation Format

Share Document