Screening of fast biofilm formation on stainless steel by thermophilic sporeformers originated from dairy powder and their resistance against CIP

2020 ◽  
Author(s):  
Louis Delaunay ◽  
Florence Postollec ◽  
Ivan Leguerinel ◽  
Anne-Gabrielle Mathot

<p><strong>Introduction: </strong></p> <p>Thermophilic sporeformers are present in raw milk at very low concentration and resist to pasteurisation applicated to destruct vegetative and pathogenic cells. Those spores can adhere to stainless steel due to their hydrophobicity and can form biofilms. Early stage biofilms are important because it can increase the matrix and the adhesion of other cells. Because of those biofilms, the three main species: Geobacillus stearothermophilus, Anoxybacillus flavithermus and Bacillus licheniformis can resists to Cleaning In Place (CIP) procedure, and contaminate a new process.</p> <p> </p> <p><strong>Material and Methods: </strong></p> <p>Early stage adhesion was conducted on stainless steel submerged by milk inoculated with a fresh culture of bacteria (G. stearothermophilus (N=15), A. flavithermus (N=32) and B. licheniformis (N=15)) for 6h of growth at 55°C under agitation. The ability of sporeformers to form biofilms under those conditions were measured by image analysis after a fluorescent coloration (acridine orange) and random photography. A coverage percentage was calculated by ImageJ ; and a positive threshold was set up at 5% of covering.</p> <p>The efficiency of CIP procedures were obtained after a caustic soda and nitric acid treatment during different duration and temperature of treatment. Tested biofilms were formed in milk during 12h at 55°C, in stainless steel microplates (96 wells) on the same species (3 strains for each) under agitation. Surviving spores were enumerated by the microcolony method.</p> <p> </p> <p><strong>Results:</strong></p> <p>Early stage adhesion shows that 62.5 % (N=20) of A. flavithermus strains can form biofilm within 6h, whereas only 6.7% (N=1) of G. stearothermophilus and 0% (N=0) of B. licheniformis biofilm in 6h at 55°C on submerged stainless steel. However, the maximum covering % on A. flavithermus was 35%; while on the only biofilm forming strain of G. stearothermophilus, this percentage reach 75%. Image analysis also shows biofilm structure from 2D to 3D.</p> <p>The presence and the resistance of spores to chemical cleaning was highly variable within strains. Nitric acid appears to be more effective than caustic soda against biofilms formed by vegetative cells and spores from these strains.</p> <p> </p> <p><strong>Significance: </strong></p> <p>Those results shows that strong biofilms are mainly composed of spore and are very resistant to CIP used in dairy industries. That is why a better understanding of control methods can lead to a finer and suitableness use of cleaning products.</p>

Author(s):  
M. R. Pinnel ◽  
A. Lawley

Numerous phenomenological descriptions of the mechanical behavior of composite materials have been developed. There is now an urgent need to study and interpret deformation behavior, load transfer, and strain distribution, in terms of micromechanisms at the atomic level. One approach is to characterize dislocation substructure resulting from specific test conditions by the various techniques of transmission electron microscopy. The present paper describes a technique for the preparation of electron transparent composites of aluminum-stainless steel, such that examination of the matrix-fiber (wire), or interfacial region is possible. Dislocation substructures are currently under examination following tensile, compressive, and creep loading. The technique complements and extends the one other study in this area by Hancock.The composite examined was hot-pressed (argon atmosphere) 99.99% aluminum reinforced with 15% volume fraction stainless steel wire (0.006″ dia.).Foils were prepared so that the stainless steel wires run longitudinally in the plane of the specimen i.e. the electron beam is perpendicular to the axes of the wires. The initial step involves cutting slices ∼0.040″ in thickness on a diamond slitting wheel.


2015 ◽  
Vol 6 (2) ◽  
pp. 253-274
Author(s):  
Vered Noam

The rabbinic halakhic system, with its many facets and the literary works that comprise it, reflects a new Jewish culture, almost completely distinct in its halakhic content and scope from the biblical and postbiblical culture that preceded it. By examining Jewish legislation in the area of corpse impurity as a test case, the article studies the implications of Qumranic halakhah, as a way-station between the Bible and the Mishnah, for understanding how Tannaitic halakhah developed. The impression obtained from the material reviewed in the article is that the direction of the “Tannaitic revolution” was charted, its methods set up, and its principles established, at a surprisingly early stage, before the destruction of the Second Temple, and thus at the same time that the Qumran literature was created.


Alloy Digest ◽  
1972 ◽  
Vol 21 (5) ◽  

Abstract SANDVIK 2RE10 is a high-chromium, high-nickel, extra-low-carbon austenitic stainless steel with high resistance to oxidizing media such as concentrated nitric acid, high resistance to intergranular corrosion and good structural stability. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-272. Producer or source: Sandvik. See also Alloy Digest SS-491, November 1987.


Alloy Digest ◽  
1975 ◽  
Vol 24 (8) ◽  

Abstract Type CB-30 is an iron-chromium alloy sufficiently high in chromium content to provide excellent resistance to corrosion by nitric acid, alkaline solutions and many organic chemicals. They alloy maintains an essentially ferritic structure. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: SS-315. Producer or source: Stainless steel foundries.


Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 231
Author(s):  
Patrick Fayek ◽  
Sebastian Esser ◽  
Vanessa Quiroz ◽  
Chong Dae Kim

Hydrogen is nowadays in focus as an energy carrier that is locally emission free. Especially in combination with fuel-cells, hydrogen offers the possibility of a CO2 neutral mobility, provided that the hydrogen is produced with renewable energy. Structural parts of automotive components are often made of steel, but unfortunately they may show degradation of the mechanical properties when in contact with hydrogen. Under certain service conditions, hydrogen uptake into the applied material can occur. To ensure a safe operation of automotive components, it is therefore necessary to investigate the time, temperature and pressure dependent hydrogen uptake of certain steels, e.g., to deduct suitable testing concepts that also consider a long term service application. To investigate the material dependent hydrogen uptake, a tubular autoclave was set-up. The underlying paper describes the set-up of this autoclave that can be pressurised up to 20 MPa at room temperature and can be heated up to a temperature of 250 °C, due to an externally applied heating sleeve. The second focus of the paper is the investigation of the pressure dependent hydrogen solubility of the martensitic stainless steel 1.4418. The autoclave offers a very fast insertion and exertion of samples and therefore has significant advantages compared to commonly larger autoclaves. Results of hydrogen charging experiments are presented, that were conducted on the Nickel-martensitic stainless steel 1.4418. Cylindrical samples 3 mm in diameter and 10 mm in length were hydrogen charged within the autoclave and subsequently measured using thermal desorption spectroscopy (TDS). The results show how hydrogen sorption curves can be effectively collected to investigate its dependence on time, temperature and hydrogen pressure, thus enabling, e.g., the deduction of hydrogen diffusion coefficients and hydrogen pre-charging concepts for material testing.


Dairy ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 270-287
Author(s):  
Roberto Anedda ◽  
Riccardo Melis ◽  
Elena Curti

Fiore Sardo (FS), a traditional Italian cheese, is present in the market as a heterogeneous variety of products. The use of heat-treated (HT) milk is forbidden by the official production protocol, but no official analytical method able to detect heat application is yet available. Here, a combined magnetic resonance imaging (MRI) relaxometry and image analysis approach to recognize FS made from raw milk is presented. Artisanal FS cheeses were produced from raw milk (RC) by five shepherds in accordance with the official protocol. They were compared to HT-milk counterparts (HTC). Additionally, industrially manufactured commercial FS cheeses (I) were also purchased and compared to RC and HTC. Relaxometry data of FS indicated the presence of two water populations; the ratio of characteristic relaxation time constant T2 and area fraction (Score, Ṩ) of the fastest relaxing population was used to compare RC, HTC and I samples. RC from HTC were successfully discriminated, the latter exhibiting lower Ṩ (enhanced protein hydration). I cheeses exhibited the lowest Ṩ values, sometimes comparable to HTC. Since visual appearance of RC and HTC is appreciably different, an image analysis deep learning approach using MRI and photographic pictures was adopted to discriminate the two productions, with promising percentages (>93%).


Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1211
Author(s):  
Maja Vončina ◽  
Aleš Nagode ◽  
Jožef Medved ◽  
Irena Paulin ◽  
Borut Žužek ◽  
...  

When extruding the casted rods from EN AW 2011 aluminium alloys, not only their homogenized structure, but also their extrudable properties were significantly influenced by the hardness of the alloy. In this study, the object of investigations was the EN AW 2011 aluminium alloy, and the effect of homogenisation time on hardness was investigated. First, homogenisation was carried out at 520 °C for different times, imitating industrial conditions. After homogenisation, the samples were analysed by hardness measurements and further characterised by microscopy and image analysis to verify the influence of homogenisation on the resulting microstructural constituents. In addition, non-equilibrium solidification was simulated using the program Thermo-Calc and phase formation during solidification was investigated. The homogenisation process enabled more rounded shape of the Al2Cu eutectic phase, equilibrium formation of the phases, and the precipitation in the matrix, leading to a significant increase in the hardness of the EN AW 2011 aluminium alloy. The experimental data revealed a suitable homogenisation time of 4–6 h at a temperature of 520 °C, enabling optimal extrusion properties.


Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 819
Author(s):  
Changsheng Li ◽  
Kun Li ◽  
Jingbo Dong ◽  
Jinyi Ren ◽  
Yanlei Song

The effect of aging on the precipitates, mechanical and magnetic properties of Fe-21Cr-15Ni-6Mn-Nb low magnetic stainless steel were investigated. The steel was aged at 550–750 °C for 2 h after solution heat treatment at 1100 °C for 1 h. During the aging treatment, the (Nb, V)(C, N) particles gradually precipitated in the grain, which were coherent or semi-coherent with the matrix. When the aging temperature was beyond 650 °C, the coarsening rate of (Nb, V)(C, N) particles increase rapidly and the coherent orientation between (Nb, V)(C, N) particles and the matrix was lost gradually. Meanwhile, coarse M23C6 was distributed at the grain boundary with chain shape, which was non-coherent with the matrix. The coarsening behavior of (Nb, V)(C, N) precipitates in the grain was analyzed, and the size of the particles precipitated after aging treatment at 650°C for different time was calculated and studied. After aging treatment at 650 °C for 2 h, the yield strength and tensile strength of the stainless steel was 705.6 MPa and 1002.3 MPa, the elongation and the relative magnetic permeability was 37.8% and 1.0035, respectively.


Sign in / Sign up

Export Citation Format

Share Document