SYNTHESIS AND CHARACTERIZATION OF NEEM-BASED ZINC OXIDE PHOTOCATALYST

2021 ◽  
Vol 36 (1) ◽  
pp. 9-15
Author(s):  
I.N Gana ◽  
V.U Ohageria ◽  
U.G Akpan ◽  
I.J Ani
Keyword(s):  
Zinc Oxide ◽  
Green Synthesis ◽  
Surface Area ◽  
Leaf Extract ◽  
Zinc Acetate Dihydrate ◽  
Sol Gel ◽  
Sem Analysis ◽  
X Ray ◽  
Bet Analysis ◽  
Neem Leaf Extract

The use of chemicals for the synthesis of photocatalyts poses threat to the environment. In this study, an active photocatalyst, Dalbejiya Dongoyaro (Azadirachta indica)-based zinc oxide (ZnO) was biosynthesized from zinc acetate dihydrate using sol gel and precipitation methods. The synthesized samples were characterized using Fourier Transfer InfraRed (FTIR), X-Ray Diffractometry (XRD), Brunauer Emmet Teller (BET), Energy Dispersive X-ray Spectroscopy (EDS) and Scanning Electron Microscopy (SEM) characterization techniques. The XRD and SEM analysis of the green synthesized and non-green synthesized ZnO demonstrated the formation of hexagonal wurtzite crystalline structure and agglomerated morphology. EDX analysis demonstrated the existence of Zn and O as the major constituents of the as-synthesized nanoparticles with traces of carbon which could be attributed to the carbon tape of the sample holder. The BET analysis displayed that the surface area of the ZnO nanoparticles increased from 23.75 to 97.08 cm3/g after the green synthesis. Based on the surface area values, it can be derived that neem leaf extract enhanced the surface area of the green synthesized sample. Green synthesis is a promising route for the synthesis of photocatalyst nanoparticle which is environmentally friendly and sustainable method. Keywords: Zinc oxide, Neem leaf extract, Photocatalyt, Degradation, Bio-synthesis

scholarly journals Green synthesis of magnetic α–Fe2O3 nanospheres using Bridelia retusa leaf extract for Fenton-like degradation of crystal violet dye

2021 ◽  
Author(s):  
Raja Selvaraj ◽  
Shraddha Pai ◽  
Gokulakrishnan Murugesan ◽  
Sadanand Pandey ◽  
Ruchi Bhole ◽  
...  
Keyword(s):  
Iron Oxide ◽  
Green Synthesis ◽  
Crystal Violet ◽  
Leaf Extract ◽  
Bet Analysis ◽  
Crystal Violet Dye ◽  
Pros And Cons ◽  
Manufacturing Techniques ◽  
The Stability ◽  
Bridelia Retusa

AbstractThe reach of nanotechnology has permeated into a range of disciplines and systematically revolutionized many manufacturing techniques. Today, nanoparticles are fabricated using varied approaches, each with its pros and cons. Of them, the green synthesis approach has been very effective in terms of overall economics and the stability of nanoparticles. The current study investigates the use of the leaf extract of Bridelia retusa for the synthesis of iron oxide nanoparticles. Typical of these nanoparticles, no specific peak was discernible on employing UV–visible spectroscopy. The size, morphological features, and crystallinity of the nanoparticles were determined by employing scanning electron microscopy and electron diffraction spectroscopy. Almost uniformly sized at 38.58 nm, the nanoparticles were spherical, constituting elemental iron at 11.5% and elemental oxygen at 59%. Their relative composition confirmed the nanoparticles to be iron oxide. X-ray diffraction studies showed the particles to be hexagonal and rhombohedral, estimating the crystallite size at 24.27 nm. BET analysis put the pore volume at 0.1198 cm3/g and pore diameter at 7.92 nm. The unique feature of the nanoparticles was that the specific surface area was 75.19 m2/g, which is more than 12 times higher than commercial α-Fe2O3. The participation of a variety of biochemicals in the leaf extract towards the reduction-cum-stabilization was confirmed using FTIR analysis. The Fenton-like catalytic activity of the nanoparticles was put to test by attempting to degrade crystal violet dye, which was completely achieved in 270 min. The kinetics of the degradation was also modelled in the study.

scholarly journals Green synthesis and characterization of hexaferrite strontium-perovskite strontium photocatalyst nanocomposites

2020 ◽  
Vol 43 (1) ◽  
pp. 26-42 ◽  
Author(s):  
Zahra Hajian Karahroudi ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Magnetic Properties ◽  
Green Synthesis ◽  
Sol Gel ◽  
Synthesis Method ◽  
Combustion Method ◽  
Lemon Juice ◽  
X Ray Diffraction ◽  
X Ray ◽  
Auto Combustion

AbstractThis study presents a preparation of SrFe12O19– SrTiO3 nanocomposite synthesis via the green auto-combustion method. At first, SrFe12O19 nanoparticles were synthesized as a core and then, SrTiO3 nanoparticles were prepared as a shell for it to manufacture SrFe12O19–SrTiO3 nanocomposite. A novel sol-gel auto-combustion green synthesis method has been used with lemon juice as a capping agent. The prepared SrFe12O19–SrTiO3 nanocomposites were characterized by using several techniques to characterize their structural, morphological and magnetic properties. The crystal structures of the nanocomposite were investigated via X-ray diffraction (XRD). The morphology of SrFe12O19– SrTiO3 nanocomposite was studied by using a scanning electron microscope (SEM). The elemental composition of the materials was analyzed by an energy-dispersive X-ray (EDX). Magnetic properties and hysteresis loop of nanopowder were characterized via vibrating sample magnetometer (VSM) in the room temperature. Fourier transform infrared spectroscopy (FTIR) spectra of the samples showed the molecular bands of nanoparticles. Also, the photocatalytic behavior of nanocomposites has been checked by the degradation of azo dyes under irradiation of ultraviolet light.

Deposition of Cobalt Doped Zinc Oxide Thin Film Nano-Composites Via Pulsed Electron Beam Ablation

MRS Advances ◽  
2016 ◽  
Vol 1 (6) ◽  
pp. 433-439 ◽  
Author(s):  
Asghar Ali ◽  
Patrick Morrow ◽  
Redhouane Henda ◽  
Ragnar Fagerberg
Keyword(s):  
Zinc Oxide ◽  
Electron Beam ◽  
Binding Energy ◽  
Photoelectron Spectroscopy ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Oxide Thin Film ◽  
X Ray ◽  
Pulsed Electron Beam ◽  
Deposited Films

AbstractThis study reports on the preparation of cobalt doped zinc oxide (Co:ZnO) films via pulsed electron beam ablation (PEBA) from a single target containing 20 w% Co on sapphire (0001) and silicon (100) substrates. The films have been deposited at various temperatures (350оC, 400оC, 450оC) and pulse frequencies (2 Hz, 4 Hz), under a background argon (Ar) pressure of about 3 mtorr, and an accelerating voltage of 14 kV. The surface morphology has been examined by atomic force microscopy (AFM) and scanning electron microscopy (SEM). According to SEM analysis, the films consist of nano-globules whose size is in the range of 80-178 nm. Energy dispersive x-ray spectroscopy (EDX) reveals that deposition is congruent and the prepared films contain ∼20±5 w% cobalt. It has been found that the nano-globules in the deposited films are cobalt-rich zones containing ∼70 w% Co. From x-ray photoelectron spectroscopy (XPS) analysis, Co 2p3/2 peaks indicate that the deposited films contain CoO (binding energy = 780.5 eV) as well as metallic Co (binding energy = 778.1-778.5 eV). X-ray diffraction (XRD) analysis supports the presence of metallic Co hcp phase (2ϴ = 44.47° and 47.43°) in the films.

scholarly journals Tuning the Morphological Properties of Cellulose Aerogels: An Investigation of Salt-Mediated Preparation

2021 ◽  
Author(s):  
Prakash Parajuli ◽  
Sanjit Acharya ◽  
Julia Shamshina ◽  
Noureddine Abidi
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Earth Metal ◽  
Morphological Properties ◽  
Cellulose Solution ◽  
Bet Analysis ◽  
Sol Gel Transition ◽  
Gel Transition

Abstract In this study, alkali and alkaline earth metal chlorides with different cationic radii (LiCl, NaCl, and KCl, MgCl2, and CaCl2) were used to gain insight into the behavior of cellulose solutions in the presence of salts. The specific focus of the study was evaluation of the effect of salts’ addition on the sol-gel transition of the cellulose solutions and on their ability to form monoliths, as well as evaluation of the morphology (e.g., specific surface area, pore characteristics, and microstructure) of aerocelluloses prepared from these solutions. The effect of the salt addition on the sol-gel transition of cellulose solutions was studied using rheology, and morphology of resultant aerogels was evaluated by Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis, while the salt influence on the aerocelluloses’ crystalline structure and thermal stability was evaluated using powder X-Ray Diffraction (pXRD) and Thermogravimetric Analysis (TGA), respectively. The study revealed that the effect of salts’ addition was dependent on the component ions and their concentration. The addition of salts in the amount below certain concentration limit significantly improved the ability of the cellulose solutions to form monoliths and reduced the sol-gel transition time. Salts of lower cationic radii had a greater effect on gelation. However, excessive amount of salts resulted in the formation of fragile monoliths or no formation of gels at all. Analysis of surface morphology demonstrated that the addition of salts resulted in a significant increase in porosity and specific surface area, with salts of lower cationic radii leading to aerogels with much larger (~1.5 and 1.6-fold for LiCl and MgCl2, respectively) specific surface area compared to aerocelluloses prepared with no added salt. Thus, by adding the appropriate salt into the cellulose solution prior to gelation, the properties of aerocelluloses that control material’s performance (specific surface area, density, and porosity) could be tailored for a specific application.

scholarly journals Effect of Re and Tm-site on morphology structure and optical band gap of ReTmO3 (Re: La, Ce, Nd, Gd, Dy, Y and Tm: Fe, Cr) prepared by sol-gel method

2018 ◽  
Vol 64 (4) ◽  
pp. 381
Author(s):  
Muhammad Tufiq Jamil ◽  
Javed Ahmad ◽  
Syed Hamad Bukhari ◽  
Murtaza Saleem
Keyword(s):  
Band Gap ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
X Ray ◽  
Average Grain Size ◽  
Auto Combustion ◽  
Uv Visible

Rare earth nano sized pollycrystalline orthoferrites and orthocromites ReT mO3 (Re = La, Nd, Gd, Dy, Y and T m = Fe, Cr) have been synthesized by sol-gel auto combustion citrate method. The samples have been characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and UV-visible spectroscopy. The samples are single phase as confirmed by XRD analysis and correspond to the orthorhombic crystal symmetry with space group pbnm. Debye Scherer formula and Williamson Hall analysis have been used to calculate the average grain size which is consistent with that of determined from SEM analysis and varied between 25-75 nm. The elemental compositions of all samples have been checked by EDX analysis. Different crystallographic parameters are calculated with strong structural correlation among Re and Tm sites. The optical energy band gap has been calculated by using Tauc relation estimated to be in the range of 1.77 - 1.87 eV and 2.77 - 3.14 eV, for ReFeO3 and ReCrO3, respectively.

Facile Electrospinning Preparation of Y3Al5O12 Nanobelts

2013 ◽  
Vol 448-453 ◽  
pp. 3041-3045
Author(s):  
Fei Bi ◽  
Xiang Ting Dong ◽  
Jin Xian Wang ◽  
Gui Xia Liu ◽  
Wen Sheng Yu
Keyword(s):  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Ftir Analysis ◽  
X Ray ◽  
Novel Structure ◽  
Group I ◽  
Sol Gel Process ◽  
Composite Nanobelts ◽  
Scanning Electron

PVP/[Y(NO3)3+Al (NO3)3] composite nanobelts were fabricated via electrospinning combined with sol-gel process and novel structure of Y3Al5O12(denoted as YAG for short) nanobelts have been obtained after calcination of the relevant composite nanobelts. The structural properties were characterized by X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XRD analysis indicated that the composite nanobelts were amorphous, and YAG nanobelts were cubic in structure with space group Ia3d. FTIR analysis manifested that pure YAG nanobelts were formed at 900oC. SEM analysis and histograms revealed that the width of the composite nanobelts and YAG nanobelts were 3.5 μm and 2.4 μm, and the thickness were 240 nm and 112 nm, respectively, under the 95% confidence level. The formation mechanism of YAG nanobelts was discussed in detail.

Ultra-sonication enhanced green synthesis of silver nanoparticles using Barleria buxifolia leaf extract and its possible application

2021 ◽  
Author(s):  
Vanaraj sekar
Keyword(s):  
Silver Nanoparticles ◽  
Green Synthesis ◽  
Leaf Extract ◽  
Cancer Cell Line ◽  
Xrd Analysis ◽  
Blue Dye ◽  
Multiple Use ◽  
Uniform Size ◽  
X Ray ◽  
Vis Spectroscopy

Abstract A simple and eco-friendly method for the green synthesis of silver nanoparticles (AgNPs) by ultrasound-assisted strategy using Barleria buxifolia leaf extract as a reducing and capping agent was established in this study. The obtained AgNPs were characterized. UV-vis spectrum, Fourier transform infrared spectroscopy (FTIR), scanning and transmission electron microscopy (SEM and TEM), Energy Dispersive X-Ray Analyzer (EDX), X-ray diffraction, dynamic light scattering (DLS) analysis showed that the obtained AgNPs were mono dispersed spheres with uniform size of 80 nm. UV-vis spectroscopy, FTIR, and XRD analysis indicated that the surface of the obtained AgNPs was covered with organic molecules in plant extracts. The results of ABTS assays showed that high antioxidant activity was seen in the obtained AgNPs. Green synthesized AgNPs showed potent antibacterial and anti-biofilm activity against tested pathogens. Cytotoxicity assay showed that the obtained AgNPs were significantly cytotoxic to cancer cell line (MCF-7). In addition, the AgNPs synthesized in this paper can also photo catalytically degrade methylene blue dye under visible light. The potent bioactivity exhibited by the green synthesized silver nanoparticles leads towards the multiple use as antioxidant, antibacterial, anti-biofilm, cytotoxic as well as photo catalytic agent.

Antibacterial Activity of Nickel -Doped ZnO\MWCNTs hybrid Prepared by Sol-Gel technique

2021 ◽  
Author(s):  
Selma M.H. AL-Jawad ◽  
Zahraa S. Shakir ◽  
Duha S. Ahmed
Keyword(s):  
Antibacterial Activity ◽  
Sol Gel ◽  
Inhibition Zone ◽  
Sem Analysis ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Zno Nps ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Doped Zno

ZnO/MWCNTs hybrid and doped with different concentration of Nickel element prepared by using Sol-gel been technique reported. All samples were prepared and characterized by X-Ray Diffraction Analysis (XRD), Energy Dispersive X-ray Spectroscopy (EDS), Fourier-Transform Infrared Spectroscopy (FTIR), Field-Emission Scanning Electron Microscopy (FE-SEM), and UV-Vis spectroscopy have been identified the structural, optical and morphological properties. X-ray diffraction showed the polycrystalline nature with hexagonal wutzite structure of hybrid and doped with Nickel. The crystalline size of the hybrid nanostructure was increasing from 23.73 nm to 34.59 nm. Besides, the UV-Vis spectroscopy showed a significant decrease in the band gap values from 2.97 eV to 2.01 eV. Whereas the FE-SEM analysis confirm the formation spherical shapes of ZnO NPs deposited on cylindrical tubes representing the MWCNTs. The antibacterial activity reveals that the inhibition zone of Ni doped-ZnO/MWCNTs hybrid was 28.5 mm, 26.5 mm toward E. coli and S. aureus bacteria, respectively.

Sign in / Sign up

Export Citation Format

Share Document