Behavior of Cohesive Soil Reinforced by Polypropylene Fiber

2020 ◽  
Vol 38 (6A) ◽  
pp. 801-812
Author(s):  
Mohammed A. Al-Neami ◽  
Falah H. Rahil ◽  
Yaseen H. Al-Ani
Keyword(s):  
Soil Stabilization ◽  
Critical Role ◽  
Polypropylene Fiber ◽  
Dry Weight ◽  
Cohesive Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Entire Structure ◽  
Optimum Water Content ◽  
Optimum Water

For any land-based structure, the foundation is very important and has to be strong to support the entire structure. In order for the foundation to be strong, the soil underneath it plays a very critical role. Some projects where the soil compacted by modifying energy is insufficient to achieve the required results, so the additives as a kind of installation and reinforcement are used to achieve the required improvement. This study introduces an attempt to improve cohesive soil by using Polypropylene Fiber instead of conventional kinds used in soil stabilization. Three different percentages (0.25%, 0.5%, and 0.75% by dry weight of soil) and lengths (6, 12, and 18) mm of fiber are mixed with cohesive as a trial to enhance some properties of clay. The results of soil samples prepared at a dry density at three different water conditions (optimum water content, dry side, and wet side) showed that the increase of the percentage and length of polypropylene fiber causes a reduction in the maximum dry density of soils. Soil cohesion increases with the increase of PPF up to 0.5% then decreased. The length of Polypropylene fiber has a great effect on the cohesion of soil and adding 0.5% Polypropylene fibers with a length of 18mm to the soils consider the optimum mix for design purposes to improve the soil. Finally, the soil reinforced by PPF exhibits a reduction in the values of the compression ratio (CR) and accelerates the consolidation of the soil.

scholarly journals Verification of the effect of Raw Materials Mill Dust on soil stabilization: An experimental study

2020 ◽  
Vol 9 (1) ◽  
pp. 172-177
Keyword(s):  
Soil Stabilization ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Dry Weight ◽  
Plasticity Index ◽  
Cement Kiln ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Pavement Maintenance ◽  
Optimum Water Content

Cement plants produce large quantities of dust, which is an important source of pollution. Among these pollutants is raw materials mill dust (RMMD), it is a dust produced during the grinding of raw materials. RMMD differs in chemical composition from cement kiln dust (CKD), where CKD is a by-product that collects in the electrostatic filters of a cement kiln. A lot of studies have been done around the world to find effective ways to recycle CKD and use it again in soil stabilization to avoid the failure of the entire pavement in the future as well as an economical and environmental solution, while there is a dearth of research done on RMMD. In this study, the performance of a weak subgrade for one of the sites in Aleppo city was examined, where its physical and mechanical properties (plasticity index, maximum dry density, optimum water content, and California bearing ratio (CBR)), were determined. Then RMMD was added to the subgrade samples according to five ratios 0, 5, 10, 15, and 20% of the dry weight of the soil. The research concluded that adding the RMMD to the weak subgrade by 20% of its dry weight is the optimal ratio, improved its performance, as the plasticity index decreased by 13%, and the CBR increased up to 63 %. Thus, the bearing capacity increases, it saves costs and reduces future pavement maintenance.

scholarly journals Compaction and Plasticity Comparative Behaviour of Soft Clay Treated with Coarse and Fine Sizes of Ceramic Tiles

2018 ◽  
Vol 34 ◽  
pp. 01012 ◽  
Author(s):  
Mohammed Ali Mohammed Al-Bared ◽  
Aminaton Marto ◽  
Indra Sati Hamonangan Harahap ◽  
Fauziah Kasim
Keyword(s):  
Soil Stabilization ◽  
Soft Soil ◽  
Soft Clay ◽  
Cost Effective ◽  
Dry Weight ◽  
Dry Density ◽  
Ceramic Tiles ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stiff Soil

Recycled blended ceramic tiles (RBT) is a waste material produced from ceramic tile factories and construction activities. RBT is found to be cost effective, sustainable, environmental-friendly and has the potential to be used as an additive in soft soil stabilization. Recent reports show that massive amounts of RBT are dumped into legal or illegal landfills every year consuming very large spaces and creating major environmental problems. On the other hand, dredged marine clay obtained from Nusajaya, Johor, Malaysia has weak physical and engineering characteristics to be considered as unsuitable soft soil that is usually excavated, dumped into landfills and replaced by stiff soil. Hence, this study investigates the suitability of possible uses of RBT to treat marine clay. Laboratory tests included Standard proctor tests and Atterberg limits tests. The plasticity of marine clay was evaluated by adding 10%, 20%, 30% and 40% of 0.3 mm RBT. In addition, the compaction behaviour of treated marine clay was compared by adding two different sizes (0.3 mm and 1.18 mm diameter) of RBT. For both coarse and fine sizes of RBT, 10%, 20%, 30% and 40% of the dry weight of the soft clay were added. The mixture of each combination was examined in order to evaluate the Maximum Dry Density (MDD) and the optimum moisture content (OMC) for the treated soft clay. MDD and OMC for soft untreated samples were 1.59 Mg/m3 and 22%, respectively. Treated samples with 10%, 20%, 30% and 40% of 0.30 mm size RBT resulted in a significant reduction of OMC ranged from 19 to 15% while MDD resulted in increment ranged from 1.69 to 1.77 Mg/m3. In addition, samples treated with 10%, 20%, 30% and 40% of 1.18 mm size RBT resulted in major reduction of OMC ranged from 15 to 13.5% while MDD increased effectively from 1.75 to 1.82 Mg/m3. For all mix designs of soft clay-RBT, MDD was gradually increasing and OMC was sharply reducing with further increments of both sizes of RBT.

Aspects of the behaviour of compacted clayey soils on drying and wetting paths

2002 ◽  
Vol 39 (6) ◽  
pp. 1341-1357 ◽  
Author(s):  
Jean-Marie Fleureau ◽  
Jean-Claude Verbrugge ◽  
Pedro J Huergo ◽  
António Gomes Correia ◽  
Siba Kheirbek-Saoud
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Dry Density ◽  
Clayey Soils ◽  
Maximum Dry Density ◽  
Optimum Water Content ◽  
Optimum Water

A relatively large number of drying and wetting tests have been performed on clayey soils compacted at the standard or modified Proctor optimum water content and maximum density and compared with tests on normally consolidated or overconsolidated soils. The results show that drying and wetting paths on compacted soils are fairly linear and reversible in the void ratio or water content versus negative pore-water pressure planes. On the wet side of the optimum, the wetting paths are independent of the compaction water content and can be approached by compaction tests with measurement of the negative pore-water pressure. Correlations have been established between the liquid limit of the soils and such properties as the optimum water content and negative pore-water pressure, the maximum dry density, and the swelling or drying index. Although based on a limited number of tests, these correlations provide a fairly good basis to model the drying–wetting paths when all the necessary data are not available.Key words: compaction, unsaturated soils, clays, drying, wetting, Proctor conditions.

scholarly journals Using Nanomaterials in Stabilization of Soil for Oil Infrastructures

2020 ◽  
Vol 10 (3) ◽  
pp. 36-53
Author(s):  
Dr. Zaid Hameed Majeed ◽  
Eng. Kadhim Jawad Aubais ◽  
Dr. Mohd Raihan Taha
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Dry Weight ◽  
Environmental Benefits ◽  
Al2o3 Content ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Geotechnical Characteristics ◽  
Compressible Soil

The design foundations  of storage tanks for oil industry experiences significant problems due to the widespread occurrence of weak and compressible soil which resulted in foundation failure. In this study, soft soils were taken from two locations and mixed with three types of nanoparticles which were nano-alumina (nano Al2O3), nano-copper (nano CuO), and nano-magnesium (nano MgO). Nanomaterials were incorporated in small percentage (less than 1%) by dry weight of soil. The tested geotechnical characteristics included the water content, dry density, and the unconfined compressive strength. The results showed significant enhancements in the maximum dry density and unconfined compressive strength. The level of enhancement depended on the type of nanomaterials and the contents. Improved strength and hardening properties were shown with the utilization of nano CuO material in comparison to the soil samples with the other nanomaterials additions, with its optimum addition of 0.7% provided an increment rate of 662.7% while the optimum nano CuO which is about 1% showed a 532% increasing rate in the compressive strength of S1 soil. It was noted that the maximum dry density and unconfined compressive strength enhanced with the increase in the nanoparticles content until reaching a percentage in which the strength decreased. The optimum content of the nano MgO was 0.3% while the optimum nano Al2O3 content was about 0.3% for soil S1 and was about 0.1% for soil S2. The presence of nanomaterials in excessive contents caused agglomeration of particles which had negative influences on mechanical characteristics of the soils. Generally, the incorporation of finer particles like nanoparticles even with low amount would improve the geotechnical characteristics of soils with the consideration of the potential environmental benefits, these combined admixtures are intended to lower the cost and become a more sustainable and environmental alternative for soil stabilization

Study on Compaction Characteristics of Solidified Mud with Different Proportion of Curing Agent

2012 ◽  
Vol 535-537 ◽  
pp. 1807-1810 ◽  
Author(s):  
Chao Hui Wang ◽  
Juan Juan Zhao ◽  
Xiao Hua Wang ◽  
Xin Qi Wang ◽  
Sheng Guan Di
Keyword(s):  
Water Content ◽  
Experimental Results ◽  
Dry Density ◽  
Curing Agent ◽  
Maximum Dry Density ◽  
Compaction Characteristics ◽  
Optimum Water Content ◽  
Curing Agents ◽  
Optimum Water ◽  
Selection Of

The compacting curves of mud solidified by some curing agents, including cements, HSC301, CVC and CDK, were studied by heavy compaction tests. Based on this, prediction formulas for optimum water content and maximum dry density of solidified mud were regressed. Experimental results showed that the optimum water content of mud was increased and the maximum dry density reduced with the increasing amount of curing agent. Regression formulas were offered as a basis for the selection of mud curing agents.

scholarly journals Study on the Compaction Effect Factors of Lime-treated Loess Highway Embankments

2017 ◽  
Vol 3 (11) ◽  
pp. 1008 ◽  
Author(s):  
Yuyu Zhang ◽  
Wanjun Ye ◽  
Zuoren Wang
Keyword(s):  
Water Content ◽  
Dry Density ◽  
In Situ Tests ◽  
Maximum Dry Density ◽  
Lime Content ◽  
Optimum Water Content ◽  
Compaction Energy ◽  
Highway Embankments ◽  
Optimum Water

This paper presents a study to investigate the effects of water content, lime content and compaction energy on the compaction characteristics of lime-treated loess highway embankments. Laboratory compaction tests were conducted to determine the maximum dry density  and optimum water content  of loess with different lime Contents (0, 3, 5 and 8%), and to examine the effects of water content, lime content and compaction energy on the value of  and . In situ compaction tests were performed to obtain the in situ dry density  and the degree of compaction  of different lime-treated loess. Experimental embankments with different fill materials (0, 3, 5 and 8% lime treated loess) were compacted by different rollers during in situ tests. The results indicate that  increases due to the increase of water content . Once water content exceeds , dry density  decreases dramatically. The addition of lime induced the increase of  and the decrease of . A higher compaction energy results in a higher value of  and a lower value of . The value of  achieves it’s maximum value when in situ water content  was larger than the value of  (+1-2%). The degree of compaction  can hardly be achieved to 100% in the field construction of embankments. Higher water content and compaction energy is needed for optimum compaction.

scholarly journals Significance of Stone Waste in Strength Improvement of Soil

2020 ◽  
Vol 1 (1) ◽  
pp. 32
Author(s):  
Amit Kumar ◽  
Kiran Devi ◽  
Maninder Singh ◽  
Dharmender Kumar Soni
Keyword(s):  
Compressive Strength ◽  
Water Content ◽  
Fine Particles ◽  
Industrial Wastes ◽  
Dry Density ◽  
Regression Equations ◽  
Human Beings ◽  
Maximum Dry Density ◽  
Optimum Water Content ◽  
Optimum Water

The evolution of industries is essential for the economic growth of any country; however, this growth often comes with exploitation of natural resources and generation of wastes. The safe disposal and utilisation of industrial wastes has become essential for sustainable development. A possible approach would be to utilize these wastes in construction industries. The stone industry is one such flawed industries that generates waste in dust or slurry form; this leads harmful impacts on human beings, animals, and surrounding areas which, in turn, can lead to soil infertility. In the present study, stone waste was examined for its influence on maximum dry density (MDD), optimum water content (OMC) and unconfined compressive strength (UCS) of soil experimentally. Stone waste was used at 0%, 4%, 8%, 12%, 16% and 20% by weight of soil and UCS tests were conducted at maturing periods of 7, 14 and 21 days. Test results reported that the incorporation of stone waste improved the compressive strength value significantly. Maximum dry density was enhanced; however, optimum water content was reduced with the use of stone waste in soil due to its fine particles. Linear regression equations were also derived for various properties.

Experimental Study on Strength Characteristics of Lime - Basalt Fiber Reinforced Expansive Soil

2015 ◽  
Vol 744-746 ◽  
pp. 495-498 ◽  
Author(s):  
Xin Shan Zhuang ◽  
Xiao Yan Yu
Keyword(s):  
Unconfined Compressive Strength ◽  
Basalt Fiber ◽  
Expansive Soil ◽  
Strength Characteristics ◽  
Dominant Factor ◽  
Dry Density ◽  
Test Results ◽  
Maximum Dry Density ◽  
Optimum Water Content ◽  
Optimum Water

Expansive soil of Nanyang Province in this experiment was as the research object and the different lime-mixed rates and basalt fiber-mixed rates on the strength characteristics of expansive soil were studied. The test results show that the maximum dry density and plasticity index of reinforced expansive soil were decreased along with the increased lime-mixed rates and the optimum water content was increased in the wake of the increased lime-mixed rates under the same compaction effort; unconfined compressive strength would be a peak along with the increased lime-mixed rates, ductility of reinforced expansive soil was enhanced by the basalt fiber; expansibility of reinforced expansive soil was slashed by lime and basalt fiber which was the dominant factor.

Applied Research on Foamed Asphalt Cold-Regenerating Technique in Overhaul Engineering of Binshi Expressway

2013 ◽  
Vol 477-478 ◽  
pp. 898-903 ◽  
Author(s):  
Hong Yuan Wei ◽  
Wei Feng Zhou ◽  
Jian Yong Sun
Keyword(s):  
Applied Research ◽  
Dry Density ◽  
Control Points ◽  
Construction Technology ◽  
Maximum Dry Density ◽  
Foamed Asphalt ◽  
Mix Proportion ◽  
Optimum Water Content ◽  
Vibration Compaction ◽  
Optimum Water

Foamed asphalt cold-regenerating technique is used to study the overhaul engineering of Binshi Expressway in 2012 (Tianjin Section) to analyze influences of different milling parameters upon the grading difference of materials of recovered asphalt pavement (RAP); and vibration compaction is used to confirm the maximum dry density and the optimum water content of regenerating mixture in the design of mix proportion to provide more reliable control parameters for site construction. Furthermore, site construction technology of cold-regeneration technique is expounded and analyzed and key control points of all links are summarized to offer technical reference for promotion and application of foamed asphalt cold-regenerating technique in Tianjin.

Sign in / Sign up

Export Citation Format

Share Document