scholarly journals Graphite electrodes as bioanodes for enzymatic glucose biofuel cell

2020 ◽  
Vol 10 (4) ◽  
pp. 385-398
Author(s):  
Madhavi Bandapati ◽  
Sanket Goel ◽  
Balaj Krishnamurthy
Keyword(s):  
Electrochemical Impedance ◽  
Open Circuit ◽  
Biofuel Cell ◽  
Ambient Conditions ◽  
Variable Response ◽  
Response Characteristics ◽  
Platinum Cathode ◽  
Multi Walled Carbon Nanotubes ◽  
Cell Electrode ◽  
Glucose Oxidation Reaction

This study investigates the performance of pencil graphite (PG) electrodes to identify the grade of pencil most suitable as bioanode for enzymatic glucose biofuel cell. Pencils of H, 3H, 5H and B grades are selected for this study. The surfaces of different grade PGs are modified with carboxylic acid functionalized multi walled carbon nanotubes (COOH-MW­CNT/PG), followed by immobilization with glucose oxidase (GOx) to fabricate the respect­tive bioanodes (GOx/COOH-MWCNT/PG). Morphological and electrochemical characteri­zations are carried out using scanning electron microscopy, electrochemical impedance spectroscopy, cyclic voltammetry and energy dispersive X-ray spectroscopy. All tested PG electrodes exhibited positive results with variable response characteristics towards glucose oxidation reaction. B-grade PG bioanode is found to have the highest coverage of the deposited nanobiocomposite with the fastest electron transfer rate. The half-cell electrode assembly with this grade of PG recorded the highest current density of 4.25 mA cm-2 at physiological glucose conditions (5 mM glucose, pH 7.0). Enzymatic glucose biofuel cell assembled with B-grade PG bioanode and platinum cathode generated an open circuit potential of 149 mV and maximum power density of 0.789 µW cm−2 from 5 mM glucose at ambient conditions (25 ± 3◦C). The results obtained for B-grade PG bioanode are comparable to those of conventional carbon and glassy carbon electrodes, thus demonstrating its applicability to enzymatic glucose biofuel cells.

scholarly journals A gateway for ion transport on gas bubbles pinned onto solids

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Veton Haziri ◽  
Tu Pham Tran Nha ◽  
Avni Berisha ◽  
Jean-François Boily
Keyword(s):  
Ion Transport ◽  
Metal Ion ◽  
Electrochemical Impedance ◽  
Gas Bubbles ◽  
Open Circuit ◽  
Double Layers ◽  
Water Geochemistry ◽  
Chemical Potentials ◽  
Pore Water Geochemistry ◽  
Electric Potentials

AbstractGas bubbles grown on solids are more than simple vehicles for gas transport. They are charged particles with surfaces populated with exchangeable ions. We here unveil a gateway for alkali metal ion transport between oxygen bubbles and semi-conducting (iron oxide) and conducting (gold) surfaces. This gateway was identified by electrochemical impedance spectroscopy using an ultramicroelectrode in direct contact with bubbles pinned onto these solid surfaces. We show that this gateway is naturally present at open circuit potentials, and that negative electric potentials applied through the solid enhance ion transport. In contrast, positive potentials or contact with an insulator (polytetrafluoroethylene) attenuates transport. We propose that this gateway is generated by overlapping electric double layers of bubbles and surfaces of contrasting (electro)chemical potentials. Knowledge of this ion transfer phenomenon is essential for understanding electric shielding and reaction overpotential caused by bubbles on catalysts. This has especially important ramifications for predicting processes including mineral flotation, microfluidics, pore water geochemistry, and fuel cell technology.

scholarly journals Sacrificial Dissolution of Zinc Electroplated and Cold Galvanized Coated Steel in Saline and Soil Environments: A Comparison

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 744
Author(s):  
Ameeq Farooq ◽  
Umer Masood Chaudry ◽  
Ahsan Saleem ◽  
Kashif Mairaj Deen ◽  
Kotiba Hamad ◽  
...  
Keyword(s):  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Saline Soil ◽  
Steel Substrate ◽  
Salt Spray ◽  
Steel Structures ◽  
Open Circuit ◽  
Cyclic Polarization ◽  
Transfer Resistance ◽  
Soil Solutions

To protect steel structures, zinc coatings are mostly used as a sacrificial barrier. This research aims to estimate the dissolution tendency of the electroplated and zinc-rich cold galvanized (ZRCG) coatings of a controlled thickness (35 ± 1 μm) applied via brush and dip coating methods on the mild steel. To assess the corrosion behavior of these coated samples in 3.5% NaCl and 10% NaCl containing soil solutions, open circuit potential (OCP), cyclic polarization (CP), and electrochemical impedance spectroscopy (EIS) tests were performed. The more negative OCP and appreciably large corrosion rate of the electroplated and ZRCG coated samples in 3.5% NaCl solution highlighted the preferential dissolution of Zn coatings. However, in saline soil solution, the relatively positive OCP (>−850 mV vs. Cu/CuSO4) and lower corrosion rate of the electroplated and ZRCG coatings compared to the uncoated steel sample indicated their incapacity to protect the steel substrate. The CP scans of the zinc electroplated samples showed a positive hysteresis loop after 24 h of exposure in 3.5% NaCl and saline soil solutions attributing to the localized dissolution of the coating. Similarly, the appreciable decrease in the charge transfer resistance of the electroplated samples after 24 h of exposure corresponded to their accelerated dissolution. Compared to the localized dissolution of the electroplated and brush-coated samples, the dip-coated ZRCG samples exhibited uniform dissolution during the extended exposure (500 h) salt spray test.

scholarly journals Development of Conductive Gelatine-Methacrylate Inks for Two-Photon Polymerisation

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1038
Author(s):  
Paola Sanjuan-Alberte ◽  
Jayasheelan Vaithilingam ◽  
Jonathan C. Moore ◽  
Ricky D. Wildman ◽  
Christopher J. Tuck ◽  
...  
Keyword(s):  
Electrical Properties ◽  
Electrochemical Impedance ◽  
Induced Pluripotent Stem Cell ◽  
Precise Control ◽  
Two Photon ◽  
Ability To Act ◽  
Multi Walled Carbon Nanotubes ◽  
Induced Pluripotent ◽  
Conductive Hydrogels ◽  
Walled Carbon Nanotubes

Conductive hydrogel-based materials are attracting considerable interest for bioelectronic applications due to their ability to act as more compatible soft interfaces between biological and electrical systems. Despite significant advances that are being achieved in the manufacture of hydrogels, precise control over the topographies and architectures remains challenging. In this work, we present for the first time a strategy to manufacture structures with resolutions in the micro-/nanoscale based on hydrogels with enhanced electrical properties. Gelatine methacrylate (GelMa)-based inks were formulated for two-photon polymerisation (2PP). The electrical properties of this material were improved, compared to pristine GelMa, by dispersion of multi-walled carbon nanotubes (MWCNTs) acting as conductive nanofillers, which was confirmed by electrochemical impedance spectroscopy and cyclic voltammetry. This material was also confirmed to support human induced pluripotent stem cell-derived cardiomyocyte (hPSC-CMs) viability and growth. Ultra-thin film structures of 10 µm thickness and scaffolds were manufactured by 2PP, demonstrating the potential of this method in areas spanning tissue engineering and bioelectronics. Though further developments in the instrumentation are required to manufacture more complex structures, this work presents an innovative approach to the manufacture of conductive hydrogels in extremely low resolution.

scholarly journals Miniaturization effect of electroosmotic self-propulsive microswimmer powered by biofuel cell

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Toshiro Yamanaka ◽  
Fumihito Arai
Keyword(s):  
Theoretical Model ◽  
Femtosecond Laser ◽  
Polymer Composites ◽  
Open Circuit Potential ◽  
Vascular System ◽  
Conductive Polymer ◽  
Open Circuit ◽  
Biofuel Cell ◽  
Remarkable Feature ◽  
Conductive Polymer Composites

AbstractFor future medical microrobotics, we have proposed the concept of the electroosmotic self-propulsive microswimmer powered by biofuel cell. According to the derived theoretical model, its self-propulsion velocity is inversely proportional to the length of the microswimmer, while it is proportional to the open circuit potential generated by the biofuel cell which does not depend on its size. Therefore, under conditions where those mechanisms work, it can be expected that the smaller its microswimmer size, the faster its self-propulsion velocity. Because of its remarkable feature, this concept is considered to be suitable as propulsion mechanisms for future medical microrobots to move inside the human body through the vascular system, including capillaries. We have already proved the mechanisms by observing the several 10 μm/s velocity of 100 μm prototypes fabricated by the optical photolithography using several photomasks and alignment steps. However, the standard photolithography was not suitable for further miniaturization of prototypes due to its insufficient resolution. In this research, we adopted femtosecond-laser 3D microlithography for multi-materials composing of the conductive polymer composites and nonconductive polymer composite and succeeded in fabricating 10 μm prototypes. Then we demonstrated more than 100 μm/s velocity of the prototype experimentally and proved its validity of the smaller and faster feature.

Application of Electrochemical Techniques to Characterization of the Corrosion Behaviors of GW63 Alloys

2007 ◽  
Vol 546-549 ◽  
pp. 571-574
Author(s):  
Xing Wu Guo ◽  
Jian Wei Chang ◽  
Shang Ming He ◽  
Peng Huai Fu ◽  
Wen Jiang Ding
Keyword(s):  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Open Circuit ◽  
Cyclic Polarization ◽  
Time Curve ◽  
Completely Monotonic ◽  
Treatment Conditions ◽  
Impedance Variation ◽  
Corrosion Behaviors

The corrosion behavior of GW63 (Mg-6wt.%Gd-3wt.%Y-0.4wt.%Zr) alloys in 5% NaCl aqueous solution has been investigated by PARSTAT 2273 instrument. The Open Circuit Potential (ECORR) vs. time curve, cyclic polarization (Pitting Scans) curve and Electrochemical Impedance Spectroscopy (EIS) was measured for the GW63 alloys in as-cast and T6 heat treatment conditions. The EIS results indicated that the tendency of impedance variation for as-cast condition was monotonic decreasing, however, the tendency of variation for T6 condition was not completely monotonic but the total tendency was decreasing. The values of impedance of GW63 alloy at 0.1 Hz are about 103 ohm-cm2 for as-cast and T6 condition.

scholarly journals From Waste to Valuable Resource: Lignin as a Sustainable Anti-Corrosion Coating

Coatings ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 454 ◽  
Author(s):  
Arman Dastpak ◽  
Kirsi Yliniemi ◽  
Mariana de Oliveira Monteiro ◽  
Sarah Höhn ◽  
Sannakaisa Virtanen ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Steel Corrosion ◽  
Linear Sweep Voltammetry ◽  
Corrosion Current ◽  
Polymer Coatings ◽  
Open Circuit ◽  
Linear Sweep ◽  
Cyclic Potentiodynamic Polarization

In this study, a waste of biorefinery—lignin—is investigated as an anticorrosion coating on stainless steel. Corrosion behavior of two lignin types (hardwood beech and softwood spruce) was studied by electrochemical measurements (linear sweep voltammetry, open circuit potential, potentiostatic polarization, cyclic potentiodynamic polarization, and electrochemical impedance measurements) during exposure to simulated body fluid (SBF) or phosphate buffer (PBS). Results from linear sweep voltammetry of lignin-coated samples, in particular, demonstrated a reduction in corrosion current density between 1 and 3 orders of magnitude cf. blank stainless steel. Furthermore, results from cross cut adhesion tests on lignin-coated samples demonstrated that the best possible adhesion (grade 0) of ISO 2409 standard was achieved for the investigated novel coatings. Such findings suggest that lignin materials could transform the field of organic coatings towards more sustainable alternatives by replacing non-renewable polymer coatings.

Nano-Thick Amorphous Oxide Layer Produced by Plasma on Type 316L Stainless Steel for Improved Corrosion Resistance Under Plastic Deformation

CORROSION ◽  
10.5006/2674 ◽  
2018 ◽  
Vol 74 (9) ◽  
pp. 1011-1022 ◽  
Author(s):  
Megan Mahrokh Dorri ◽  
Stéphane Turgeon ◽  
Maxime Cloutier ◽  
Pascale Chevallier ◽  
Diego Mantovani
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
Oxide Layer ◽  
Electrochemical Impedance ◽  
Open Circuit ◽  
Localized Corrosion ◽  
Native Oxide ◽  
Native Oxide Layer ◽  
Amorphous Oxide ◽  
Amorphous Oxide Layer

Localized corrosion constitutes a major concern in medical devices made of stainless steel. The conventional approach to circumvent such a problem is to convert the surface polycrystalline microstructure of the native oxide layer to an amorphous oxide layer, a few micrometers thick. This process cannot, however, be used for devices such as stents that undergo plastic deformation during their implantation, especially those used in vascular surgery for the treatment of cardiac, neurological, and peripheral vessels. This work explores the feasibility of producing a nano-thick plastic-deformation resistant amorphous oxide layer by plasma-based surface modifications. By varying the plasma process parameters, oxide layers with different features were produced and their properties were investigated before and after clinically-relevant plastic deformation. These properties and the related corrosion mechanisms were mainly evaluated using the electrochemical methods of open-circuit potential, cyclic potentiodynamic polarization, and electrochemical impedance spectroscopy. Results showed that, under optimal conditions, the resistance to corrosion and to the permeation of ions in a phosphate buffered saline, even after deformation, was significantly enhanced.

scholarly journals Corrosion of the Welded Aluminium Alloy in 0.5 M NaCl Solution. Part 2: Coating Protection

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2177 ◽  
Author(s):  
Andrey Gnedenkov ◽  
Sergey Sinebryukhov ◽  
Dmitry Mashtalyar ◽  
Igor Vyaliy ◽  
Vladimir Egorkin ◽  
...  
Keyword(s):  
Aluminium Alloy ◽  
Welded Joint ◽  
Electrochemical Impedance ◽  
Corrosion Behaviour ◽  
Weld Interface ◽  
Open Circuit ◽  
Al Alloy ◽  
Protective Properties ◽  
Coating Formation ◽  
Electrode Technique

The high electrochemical activity of the aircraft 1579 aluminium alloy with a welded joint and the necessity of the coating formation to protect this material against corrosion as well as to increase the stability of the weld interface in the corrosive medium has been previously established. In this work, two suggested methods of protective coating formation based on plasma electrolytic oxidation (PEO) in tartrate-fluoride electrolyte significantly increased the protective properties of the welded joint area of the 1579 Al alloy. The electrochemical properties of the formed surface layers have been investigated using SVET (scanning vibrating electrode technique) and SIET (scanning ion-selective electrode technique), EIS (electrochemical impedance spectroscopy), OCP (open circuit potential), and PDP (potentiodynamic polarization) in 0.5 M NaCl. The less expressed character of the local electrochemical processes on the welded 1579 Al alloy with the composite coating in comparison with the base PEO-layer has been established. Polymer-containing coatings obtained using superdispersed polytetrafluoroethylene (SPTFE) treatment are characterized by the best possible protective properties and prevent the material from corrosion destruction. Single SPTFE treatment enables one to increase PEO-layer protection by 5.5 times. The results of this study indicate that SVET and SIET are promising to characterize and to compare corrosion behaviour of coated and uncoated samples with a welded joint in chloride-containing media.

scholarly journals Comparison of the influence of nitrate ions on the electrochemical behaviour of iron and carbon steels in sulphate solutions

2002 ◽  
Vol 67 (6) ◽  
pp. 425-436 ◽  
Author(s):  
Houy Ma ◽  
Shenhao Chen ◽  
Chao Yang ◽  
Jingli Luo
Keyword(s):  
Electrochemical Impedance ◽  
Electrochemical Behaviour ◽  
Low Frequency ◽  
Open Circuit ◽  
Carbon Steels ◽  
General Corrosion ◽  
Impedance Spectra ◽  
Nitrate Ions ◽  
Capacitive Loop ◽  
Acidic Sulphate

The effect of nitrate ions on the electrochemical behaviour of iron (ferrite) and two carbon steels (martensite and pearlite) in sulphate solutions of different pH values was investigated by cyclic voltammetry polarization and electrochemical impedance spectroscopy. The pitting inhibiting effect of nitrate ions on ferrite in sulphate media is pH dependent. Nitrate ions were unable to inhibit the pitting on ferrite in neutral sulphate solutions, but did effectively protect passivated ferrite from pitting in acidic sulphate solutions. No pitting occurred on the surface of the martensite and pearlite specimens in sulphate solutions regardless of the pH of the solutions. At the open-circuit corrosion potentials, the three materials underwent general corrosion. The impedance spectra for the three materials measured in neutral sulphate solutions containing nitrates and chlorides at the corrosion potentials all showed a capacitive loop, while in acidic sulphate solutions their impedance spectra were greatly reduced in size and displayed at least a low frequency impedance loop (inductive or capacitive loop) besides the well-known high frequency capacitive loop. The variation of the impedance behaviour with pH is explained.

Sign in / Sign up

Export Citation Format

Share Document