Modeling and Analysis of Different Architecture for Civil Aircraft Hydraulic System

For the evaluation of civil aircraft hydraulic system, Fuel Consumption is a very important index. However, there is no effective method to perform analysis for different architecture. This paper proposes that taking fuel weight penalty as a major mathmatical modeling method to analysis traditional architecture and more electric architecture. The result shows that the fuel consumption of more electric architecture is less than traditional architecture.

Self-Reboot-Mobility of Self-Cleaning Antimicrobial Industry on Textiles and Apparel for Impact of COVID-19

Self-reboot-mobility of self-cleaning antimicrobial industry on textiles and apparel is receiving an increasing amount of interest worldwide as a method to address Antimicrobial in materials. In particular, for advanced high-performance fiber-reinforced polymer of self-reboot-mobility (SRM) with composite materials, Self-reboot-mobility of self-cleaning antimicrobial industry on textiles and apparel offers an alternative to employing conservative damagetolerant designs and a mechanism for ameliorating inaccessible and invidious internal Antimicrobial within a structure. This article considers in some detail the various self-reboot-mobility of self-cleaning antimicrobial industry on textiles and apparel technologies currently being developed for SRM with composite materials. Key constraints for incorporating such a function in SRMs are that it not be detrimental to inherent mechanical properties and that it not impose a severe weight penalty

Initial sizing of a roadable personal air vehicle using design of experiments for various engine types

Purpose The purpose of this paper is to analyze and compare the performances of novel roadable personal air vehicle (PAV) concepts that meet established operational requirements with different types of engines. Design/methodology/approach The vehicle configuration was devised considering the dimensions and operational restrictions of the roads, runways and parking lots in South Korea. A folding wing design was adopted for road operations and parking. The propulsion designs considered herein use gasoline, diesel and hybrid architectures for longer-range missions. The sizing point of the roadable PAV that minimizes the wing area was selected, and the rate of climb, ground roll distance, cruise speed and service ceiling requirements were met. For various engine types and mission profiles, the performances of differently sized PAVs were compared with respect to the MTOW, wing area, wing span, thrust-to-weight ratio, wing loading, power-to-weight ratio, brake horsepower and fuel efficiency. Findings Unlike automobiles, the weight penalty of the hybrid system because of the additional electrical components reduced the fuel efficiency considerably. When the four engine types were compared, matching the total engine system weight, the internal combustion (IC) engine PAVs had better fuel efficiency rates than the hybrid powered PAVs. Finally, a gasoline-powered PAV configuration was selected as the final design because it had the lowest MTOW, despite its slightly worse fuel efficiency compared to that of the diesel-powered engine. Research limitations/implications Although an electric aircraft powered only by batteries most capitalizes on the operating cost, noise and emissions benefits of electric propulsion, it also is most hampered by range limitations. Air traffic integration or any safety, and noise issues were not accounted in this study. Practical implications Aircraft sizing is a critical aspect of a system-level study because it is a prerequisite for most design and analysis activities, including those related to the internal layout as well as cost and system effectiveness analyses. The results of this study can be implemented to design a PAV. Social implications This study can contribute to the establishment of innovative PAV concepts that can alleviate today’s transportation problems. Originality/value This study compared the sizing results of PAVs with hybrid engines with those having IC engines.

Assessment of Engine Operability and Overall Performance for Parallel Hybrid Electric Propulsion Systems for a Single-Aisle Aircraft

This paper aims to assess the gas turbine operability and overall hybrid electric propulsion system performance for a parallel configuration applied to a 150 passenger single-aisle aircraft. Two arrangements are considered: one where the low pressure shaft is boosted and one where the high pressure shaft is boosted. For identifying limits in the hybridization strategy steady state and transient operation are considered and the hybridization effect on compressor operability is determined. Having established the electric power on-take limits with respect to gas turbine operation the systems performance at aircraft level is quantified for the relevant cases. Different power management strategies are applied for the two arrangements and for different power degrees of hybridization. The results indicate that despite the fact that pollutant emission and fuel consumption may improved for hybrid propulsion, this comes at the cost of reduced payload and operability margins. Boosting the low pressure shaft may give the highest engine performance benefits but with a significant weight penalty, while the low pressure compressor system operability is negatively affected. On the other hand boosting the high pressure shaft provides lower engine performance benefits but with smaller weight penalty and with less operability concerns.

Design and Analysis Methods for Composite Bonded Joints

A literature review on existing design and analysis methods for composite adhesively bonded joints has been conducted. Methods that might form a basis for development of practical engineering methodology for adhesively bonded joints were selected and described. Starting from the simplest and the fastest analytical methods (closed-form solutions): average shear stress, shear lag model and adhesive beam model through more complex and more time consuming numerical methods supported by finite element analysis: global models, local models, cohesive zone models. Assumptions and applicability of each method was discussed. Simple and fast methods in order to be reliable have to include many conservative assumptions and therefore may lead to over-designed structure (weight penalty). Structural optimization and weight reduction require the usage of more complex and time consuming methods. Therefore, selection of adequate methods should always be balanced against strength, durability, costs and weight.

Ferrofluid thin films for aerofoil lift enhancement and delaying flow separation

ABSTRACTIn this work, consideration is given to a novel concept for aerofoil lift enhancement and delaying flow separation. Here, lift enhancement is attained by preventing the growth of the boundary layer through the elimination of the zero-slip condition between the wing surface and the air stream. The concept would simulate all the effects of a moving wall, leading to the appearance of a slip velocity at the gas–fluid interface, including the injection of momentum into the air boundary layer, but with one exception: here there is no moving wall but instead a ferrofluid thin film pumped parallel and attached to the wall by a magnetic field. Utilising a simplified physical model for the velocity profile of the ferrofluid film and based on ferrohydrodynamic stability considerations, an analytical expression for the interfacial velocity is derived. Finally, from the available experimental data on moving walls, the expected lift and angle-of-attack enhancement are found as well as the weight penalty per unit surface area of the wing is estimated. Additional research and development is required to explore the possibilities of using ferrofluid thin films.

Mechanical Joining of Fibre Reinforced Polymer Composites to Metals—A Review. Part II: Riveting, Clinching, Non-Adhesive Form-Locked Joints, Pin and Loop Joining

As fiber reinforced plastic composites gain an increasingly larger share in aerospace structures, the problem of joining them with metal elements becomes significant. The current paper is the second part of the literature review, which gathers and evaluates knowledge about methods suitable for the mechanical joining of composite and metal elements. This paper reviews the joining methods other than bolted joining, which are discussed in the first part of the review, namely self-piercing riveting, friction riveting, clinching, non-adhesive form-locked joints, pin joints, and loop joints. Some of those methods are full-fledged and employed in commercial applications, whereas others are merely ideas tested at the level of specimens. The current review describes the ideas and the qualities of the joining methods as well as the experimental work carried out so far. The summary section of this paper contains a comparison of those methods with the reference to their qualities, which is important from the point of view of a composite structure designer: possibility of the joint disassembly, damages induced in composite, complication level, weight penalty, range of possible materials to be joined, and the joint strength.

Optimization, design and testing for morphing leading edge

Wing's morphing leading edge, drooping in a seamless way, has significant potential for noise abatement and drag reduction. Innovative design methods for compliant skin and internal actuating mechanism, respectively, are proposed and validated through a mockup in this paper. For the skin, a collaborative optimization method is presented, which takes all design variables, continuous and discrete, into account simultaneously. Moreover, to overcome the drawback of conventional algorithm, which is insufficient for deformation control in critical regime, weight penalty is imposed on present objective function. On the other hand, an internal kinematic actuating mechanism is designed from an improved concept, of which positions of level-rod hinges are optimized in a larger zone to fit the deflection requirement. The test of mockup validates the above methods, and excellent morphing quality of the compliant skin proves the advancement of the collaborative optimization method. However, the design method of internal actuating mechanism needs further improvement, and the error induced deteriorates the final morphing quality of the mockup.