The influence of target film material and coating on neutron yield and sputtering yield

The long-life, high yield deuterium-deuterium (D-D) neutron tube has become one of the research hotspots. Here, deuterated polyethylene target, heavy water target and titanium target were investigated by Stopping and Range of Ions in Matter (SRIM). The calculation showed that the deuterated polyethylene target, which was a potential target material, had the highest yield at an incident energy of 120 keV. Further, considering the unfavorable factors such as impurity ions and high temperature, the coating was used to protect the target material. Diamond, boron carbide, boron nitride, silicon carbide, and aluminum carbide were selected. The simulation results showed that the diamond composite deuterated polyethylene film had the best sputtering resistance, and the aluminum nitride composite heavy water target film had the lowest sputtering yield. The two coating materials shield the target, reduced the energy loss of incident ions, and provided a new method for the research of high yield and long life neutron tube.

2 μm passively mode-locked thulium-doped fiber lasers with Ta2AlC-deposited tapered and side-polished fibers

In this work, mode-locked thulium-doped fiber lasers operating in the 2 µm wavelength region were demonstrated using tantalum aluminum carbide (Ta2AlC)-based saturable absorbers (SAs) utilizing the evanescent wave interaction. The Ta2AlC MAX Phase was prepared by dissolving the Ta2AlC powder in isopropyl alcohol and then deposited onto three different evanescent field-based devices, which were the tapered fiber, side-polished fiber, and arc-shaped fiber. Flame-brushing and wheel-polishing techniques were used to fabricate the tapered and arc-shaped fibers, respectively, while the side-polished fiber was purchased commercially. All three SA devices generated stable mode-locked pulses at center wavelengths of 1937, 1931, and 1929 nm for the tapered, side-polished, and arc-shaped fibers. The frequency of the mode-locked pulses was 10.73 MHz for the tapered fiber, 9.58 MHz for the side-polished fiber, and 10.16 MHz for the arc-shaped fiber. The measured pulse widths were 1.678, 1.734, and 1.817 ps for each of the three SA devices. The long-term stability of the mode-locked lasers was tested for each configuration over a 2-h duration. The lasers also showed little to no fluctuations in the center wavelengths and the peak optical intensities, demonstrating a reliable, ultrafast laser system.

An Evaluation of the Microstructure of High-Aluminum Cast Iron in Terms of the Replacement of Aluminum Carbide with Titanium Carbide or Tungsten Carbide

One of the problems with recycling is that of widespread contaminated steel scrap with an unwanted aluminum addition. In this paper, we will present a specific solution to this problem. The implementation of high-aluminum cast iron production has been considered. This cast iron is a cheap material resistant to high temperatures; additionally, it has increased abrasion resistance. Despite the above-mentioned advantages, high-aluminum cast iron has not been widely used in the industry so far, due to the difficulties encountered during machining and the occurrence of the phenomenon of spontaneous disintegration. The paper presents a method for replacing aluminum carbide with titanium carbide or tungsten carbide. This research shows that the carbide replacement procedure is sufficient in stopping the phenomenon of self-disintegration of a casting made of high-aluminum cast iron. Moreover, a new material was obtained, i.e., high-aluminum cast iron with precipitates of hard tungsten carbide and flake graphite. When considering the abrasive resistance of this material, flake graphite can be treated as the natural lubricant phase and tungsten carbide precipitation, as the hardening phase.

Shaping the Microstructure of High-Aluminum Cast Iron in Terms of the Phenomenon of Spontaneous Decomposition Generated by the Presence of Aluminum Carbide

A suitable aluminum additive in cast iron makes it resistant to heat in a variety of environments and increases the abrasion resistance of the cast iron. It should be noted that high-aluminum cast iron has the potential to become an important eco-material. The basic elements from which it is made—iron, aluminum and a small amount of carbon—are inexpensive components. This material can be made from contaminated aluminum scrap, which is increasingly found in metallurgical scrap. The idea is to produce iron castings with the highest possible proportion of aluminum. Such castings are heat-resistant and have good abrasive properties. The only problem to be solved is to prevent the activation of the phenomenon of spontaneous decomposition. This phenomenon is related to the Al4C3 hygroscopic aluminum carbide present in the structure of cast iron. Previous attempts to determine the causes of spontaneous disintegration by various researchers do not describe them comprehensively. In this article, the mechanism of the spontaneous disintegration of high-aluminum cast iron castings is defined. The main factor is the large relative geometric dimensions of Al4C3 carbide. In addition, methods for counteracting the phenomenon of spontaneous decay are developed, which is the main goal of the research. It is found that a reduction in the size of the Al4C3 carbide or its removal lead to the disappearance of the self-disintegration effect of high-aluminum cast iron. For this purpose, an increased cooling rate of the casting is used, as well as the addition of elements (Ti, B and Bi) to cast iron, supported in some cases by heat treatment. The tests are conducted on the cast iron with the addition of 34–36% mass aluminum. The molten metal is superheated to 1540 °C and then the cast iron samples are cast at 1420 °C. A molding sand with bentonite is used to produce casting molds.

2 μm Passively Mode-Locked Thulium-doped Fiber Lasers with Ta2AlC-deposited Tapered, Side- polished and D-shaped Fibers

In this work, mode-locked thulium-doped fiber lasers operating in the 2 µm wavelength region were demonstrated using tantalum aluminum carbide (Ta2AlC)-based saturable absorbers (SAs) utilizing the evanescent wave interaction. The Ta2AlC MAX Phase was prepared by dissolving the Ta2AlC powder in isopropyl alcohol (IPA) and then deposited onto three different evanescent field-based devices, which were the tapered fiber, side-polished fiber (SPF), and D-shaped fiber. Flame-brushing and wheel-polishing techniques were used to fabricate the tapered and D-shaped fibers, respectively, while the side-polished fiber was purchased commercially. All three SA devices generated stable mode-locked pulses at center wavelengths of 1937, 1931, and 1929 nm for the tapered, side-polished, and D-shaped fibers. The frequency of the mode-locked pulses was 10.73 MHz for the tapered fiber, 9.58 MHz for the side-polished fiber, and 10.16 MHz for the D-shaped fiber. The measured pulse widths were 1.678, 1.734, and 1.817 ps for each of the three SA devices. The long-term stability of the mode-locked lasers was tested for each configuration over a 2-hour duration. The lasers also showed little to no fluctuations in the center wavelengths and the peak optical intensities, demonstrating a reliable, ultrafast laser system.

On the Strength of the CF/Al-Wire Depending on the Fabrication Process Parameters: Melt Temperature, Time, Ultrasonic Power, and Thickness of Carbon Fiber Coating

The process of the production of a CF/Al-wire by pulling carbon fibers through an aluminum melt has at least 15 parameters. The main parameters include the power of ultrasonic treatment, the time of contact of the fiber with the matrix melt, and the melt temperature. In addition, the presence of a barrier coating on the fiber surface and its thickness significantly affects the properties of the resulting material. The importance of these parameters is due to their direct effect on the chemical interaction between the aluminum matrix and the carbon fiber. This interaction leads to the formation of aluminum carbide, a hygroscopic, brittle phase that ultimately significantly reduces the strength of such composites. In this regard, limiting a chemical reaction at the matrix/fiber interface in the production of CF/Al composites is one of the main technological problems. The main goal of this work is to pragmatically elucidate the effect of the above parameters on the strength of CF/Al composites. It is shown that the strength of a CF/Al-wire can reach 2000 MPa.

Synthesis of Ti3C2 Mxene through In Situ HF and Direct HF Etching Procedures as Electrolyte Fillers in Dye-Sensitized Solar Cell

MXene is the new family of two-dimensional (2D) transition metal carbides, carbonitrides and nitrides discovered in 2011. The unique properties of 2D MXene such as excellent mechanical properties, hydrophilic surfaces and metallic conductivity made it interesting for application in electrodes of rechargeable batteries, supercapacitors, photocatalysts, catalysts, transparent conducting films, and flexible high-strength composites. The MXene can be synthesized through a selective etching process by using either in-situ HF (hydrofluoric acid) or direct HF methods. This study reports on the effect of the in-situ HF and direct HF etching procedures on the morphology of the synthesis Ti2C3 MXene using titanium aluminum carbide (Ti2AlC3) as precursor. The morphology and elements presence were evaluated by using variable pressure field emission scanning electron microscope (FESEM) and energy dispersion X-ray (EDX) spectroscopy analyses, respectively. The analysis shows that the MXene synthesized through the direct HF method was successfully delaminated compared to the in-situ HF procedures.

Characterization of Aluminum Alloy–Silicon Carbide Functionally Graded Materials Developed by Centrifugal Casting Process

The continuous development of modern industries rises the necessity for functionally graded materials. This research starts from the consideration that the incorporation of SiC particles in the molten aluminum alloy can be difficult due to the very low wettability of SiC particles. In order to increase their wettability, SiC particles were covered with a layer of metallic copper. The incorporation of SiC particles into the aluminum alloy mass was performed by centrifugal casting. The secondary hypoeutectic Al-Si alloy used in this study was elaborated within the crucible of a resistors heated furnace. The metallic coating of SiC particles, in addition to the effect of increasing their wettability by molten metal, also has a role in preventing the formation of aluminum carbide in case of heating above 700 °C. A great amount of attention was paid to the parameters used during the centrifugal casting process. The results showed that adjusting the proportion of SiC particles within the composite allows us to obtain values of the thermal expansion coefficient within previously established limits. The present work demonstrates that the coating of SiC particles covered with a thin layer of metallic Cu creates the conditions to easily incorporate them into the molten Al mass, thus obtaining FGMs with controlled properties.