Effects of gauge length and strain rate on the tensile strength of tree roots

Trees ◽  
2012 ◽  
Vol 26 (5) ◽  
pp. 1577-1584 ◽  
Author(s):  
Chaobo Zhang ◽  
Lihua Chen ◽  
Jing Jiang ◽  
Shuo Zhou
Keyword(s):  
Tensile Strength ◽  
Strain Rate ◽  
Gauge Length ◽  
Tree Roots

Mechanical properties of low-density paper

2020 ◽  
Vol 35 (1) ◽  
pp. 61-70
Author(s):  
Na Young Park ◽  
Young Chan Ko ◽  
Lili Melani ◽  
Hyoung Jin Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Structural Change ◽  
Tensile Testing ◽  
Tensile Modulus ◽  
Gauge Length ◽  
Efficiency Factor ◽  
Low Density ◽  
Tensile Stiffness ◽  
Lower Tensile Strength

AbstractFor the mechanical properties of paper, tensile testing has been widely used. Among the tensile properties, the tensile stiffness has been used to determine the softness of low-density paper. The lower tensile stiffness, the greater softness of paper. Because the elastic region may not be clearly defined in a load-elongation curve, it is suggested to use the tensile modulus which is defined as the slope between the two points in the curve. The two points which provide the best correlation with subjective softness evaluation should be selected. Low-density paper has a much lower tensile strength, but much larger elongation at the break. It undergoes a continuous structural change during mechanical testing. The degree of the structural change should depend on tensile conditions such as the sample size, the gauge length, and the rate of elongation. For low-density paper, the tensile modulus and the tensile strength should be independent of each other. The structure efficiency factor (SEF) is defined as a ratio of the tensile strength to the tensile modulus and it may be used a guideline in developing superior low-density paper products.

Tension and Compression Behavior of Pre-Stressed Steel Strands at High Strain Rate

2011 ◽  
Vol 82 ◽  
pp. 154-159 ◽  
Author(s):  
Anatoly M. Bragov ◽  
Ezio Cadoni ◽  
Alexandr Yu. Konstantinov ◽  
Andrey K. Lomunov
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Gauge Length ◽  
Hopkinson Pressure Bar ◽  
Dog Bone ◽  
Tension And Compression ◽  
Set Up

In this paper is described the mechanical characterization at high strain rate of the high strength steel usually adopted for strands. The experimental set-up used for high strain rates testing: in tension and compression was the Split Hopkinson Pressure Bar installed in the Laboratory of Dynamic Investigation of Materials in Nizhny Novgorod. The high strain rate data in tension was obtained with dog-bone shaped specimens of 3mm in diameter and 5mm of gauge length. The specimens were screwed between incident and transmitter bars. The specimens used in compression was a cylinder of 3mm in diameter and 5mm in length. The enhancement of the mechanical properties is quite limited compared the usual reinforcing steels.

Characterization and Utilization of Coconut Fibers of the Caribbean

2014 ◽  
Vol 1611 ◽  
pp. 95-104 ◽  
Author(s):  
Nadira Mathura ◽  
Duncan Cree ◽  
Ryan P. Mulligan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Micrographs ◽  
Saline Water ◽  
Gauge Length ◽  
Scanning Electron Micrographs ◽  
Coir Fiber ◽  
Coir Fibers ◽  
The Caribbean ◽  
Scanning Electron

ABSTRACTIn many tropical countries coconut (coir) fiber production is a major source of income for rural communities. The Caribbean has an abundance of coconuts but research into utilizing its by-products is limited. Environmentally friendly coir fibers are natural polymers generally discarded as waste material in this region. Research has shown that coir fiber from other parts of the world has successfully been recycled. This paper therefore investigates the mechanical properties of Caribbean coir fiber for potential applications in civil engineering.Approximately four hundred fibers were randomly taken from a coir fiber stack and subjected to retting in both distilled and saline water media. The mechanical properties of both the retted and unretted coir fibers were evaluated at weekly increments for a period of 3 months. Tensile strength test, x-ray diffraction analysis and scanning electron micrographs were used to assess trends and relationships between fiber gauge lengths, diameter, tensile strength and Young’s modulus. Diameters ranged between 0.11 mm-0.46 mm, while fiber samples were no longer than 250 mm in length. The tensile strength and strain at break decreased as the gauge length increased for both unretted and retted fibers. The opposite occurred for the relationship between the gauge length and Young’s modulus. Additionally, the tensile strength and modulus decreased as the fiber diameter increased. Neither distilled nor saline water improved the coir fiber’s crystalline index. Scanning electron micrographs qualitatively assessed fiber surfaces and captured necking and microfibril degradation at the fractured ends.The analysis revealed that the tensile strength, modulus, strain at break and crystallinity properties of the Caribbean coir fibers were comparable to commercially available coir fiber which are currently being used in many building applications.

Tensile strength prediction of natural fiber and natural fiber yarn: Strain rate variation upshot

2020 ◽  
Vol 27 ◽  
pp. 1218-1223
Author(s):  
Sagar Chokshi ◽  
Piyush Gohil ◽  
Amul Lalakiya ◽  
Parth Patel ◽  
Amit Parmar
Keyword(s):  
Tensile Strength ◽  
Strain Rate ◽  
Natural Fiber ◽  
Strength Prediction ◽  
Rate Variation

Influence of the strain rate on the tensile strength in aluminas of different purity

2000 ◽  
Vol 10 (PR9) ◽  
pp. Pr9-323-Pr9-328 ◽  
Author(s):  
F. Gálvez ◽  
J. Rodriguez ◽  
V. Sánchez Gálvez
Keyword(s):  
Tensile Strength ◽  
Strain Rate

Tensile Properties and Fracture Behavior of SiCp/AC4CH Composite at Loading Velocities of up to 10m/s

2004 ◽  
Vol 449-452 ◽  
pp. 305-308
Author(s):  
Lei Wang ◽  
Toshiro Kobayashi ◽  
Chun Ming Liu
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Tensile Deformation ◽  
Optical Microscope ◽  
Fracture Elongation ◽  
Before And After

Tensile test at loading velocities up to 10 m·s-1(strain rate up to 3.2x102s-1) was carried out forr SiCp/AC4CH composite and AC4CH alloy. The microstructure of the composite before and after tensile deformation was carefully examined with both optical microscope and SEM. The experimental results demonstrated that the ultimate tensile strength (UTS) and yield strength (YS) increase with increasing loading velocity up to 10 m·s-1. Comparing with AC4CH alloy, the fracture elongation of the composite is sensitivity with the increasing strain rate. The YS of both the composite and AC4CH alloy shows more sensitive than that of the UTS with the increasing strain rate, especially in the range of strain rate higher than 102s-1.

The effect of temperature and strain rate on the tensile strength of a fast-gas-cooled uranium-2 wt% molybdenum alloy

1985 ◽  
Vol 132 (2) ◽  
pp. 181-191 ◽  
Author(s):  
G.A.C. Boyd ◽  
J. Harding ◽  
P.A. Bleasdale ◽  
K. Dunn ◽  
G.I. Turner
Keyword(s):  
Tensile Strength ◽  
Strain Rate ◽  
Molybdenum Alloy ◽  
Effect Of Temperature

Fracture Behavior of an AlMgMnSc Alloy at Different Temperatures

2021 ◽  
Vol 1016 ◽  
pp. 292-296
Author(s):  
Yuliya Igorevna Borisova ◽  
Diana Yuzbekova ◽  
Anna Mogucheva
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Brittle Fracture ◽  
Fracture Surface ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Fine Grained ◽  
Angular Pressing ◽  
Different Temperatures ◽  
Elongation To Failure

An Al-4.57Mg-0.35Mn-0.2Sc-0.09Zr (wt. %) alloy was studied in the fine-grained state obtaining after equal channel angular pressing. The mechanical behavior of alloy at the temperatures 173 K, 298 K and 348 K and at strain rate 1×10–3 s–1 is studied. Increase of the temperature testing from 173 K to 348 K decreases the yield stress by 80 MPa, the ultimate tensile strength by 60 MPa while elongation-to failure increases by a factor of 1.4. It was found that at temperatures of 298 and 173 K, the studied alloy mainly demonstrates the mode of ductile fracture, and at a temperature of 348 K the mechanism can be described as mixed ductile-brittle fracture. It was also established that of the studied alloy is the temperature dependence of the size of the dimples on the fracture surface. The formation of smaller dimples in the samples deformed at 298 K was observed.

scholarly journals Comprehensive Properties of a Novel Quaternary Sn-Bi-Sb-Ag Solder: Wettability, Interfacial Structure and Mechanical Properties

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 791 ◽  
Author(s):  
Kaipeng Wang ◽  
Fengjiang Wang ◽  
Ying Huang ◽  
Kai Qi
Keyword(s):  
Tensile Strength ◽  
Shear Strength ◽  
Low Temperature ◽  
Strain Rate ◽  
Isothermal Aging ◽  
Solder Joints ◽  
Solder Matrix ◽  
Interfacial Structure ◽  
Solder Alloys ◽  
Cu Substrate

Sn-58Bi eutectic solder is the most recommended low temperature Pb-free solder but is also limited from the interfacial embrittlement of Bi segregation. Since the quaternary Sn-38Bi-1.5Sb-0.7Ag solder provides a similar melting point as Sn-58Bi eutectic, this paper systematically investigated the properties of this solder from wettability, bulk tensile properties, interfacial microstructure in solder joints with a Cu substrate, interfacial evolution in joints during isothermal aging and the shear strength on ball solder joints with effect of aging conditions. The results were also compared with Sn-58Bi solder. The wettability of solder alloys was evaluated with wetting balance testing, and the quaternary Sn-38Bi-1.5Sb-0.7Ag solder had a better wettability than Sn-58Bi solder on the wetting time. Tensile tests on bulk solder alloys indicated that the quaternary Sn-38Bi-1.5Sb-0.7Ag solder had a higher tensile strength and similar elongation compared with Sn-58Bi solder due to the finely distributed SnSb and Ag3Sn intermetallics in the solder matrix. The tensile strength of solder decreased with a decrease in the strain rate and with an increase in temperature, while the elongation of solder was independent of the temperature and strain rate. When soldering with a Cu substrate, a thin Cu6Sn5 intermetallic compound (IMC) is produced at the interface in the solder joint. Measurement on IMC thickness showed that the quaternary Sn-38Bi-1.5Sb-0.7Ag had a lower IMC growth rate during the following isothermal aging. Ball shear test on solder joints illustrated that the quaternary Sn-38Bi-1.5Sb-0.7Ag solder joints had higher shear strength than Sn-58Bi solder joints. Compared with the serious deterioration on shear strength of Sn-58Bi joints from isothermal aging, the quaternary Sn-38Bi-1.5Sb-0.7Ag solder joints presented a superior high temperature stability. Therefore, the quaternary Sn-38Bi-1.5Sb-0.7Ag solder provides better performances and the possibility to replace Sn-58Bi solder to realize low temperature soldering.

Sign in / Sign up

Export Citation Format

Share Document