Fracture Behavior of an AlMgMnSc Alloy at Different Temperatures

2021 ◽  
Vol 1016 ◽  
pp. 292-296
Author(s):  
Yuliya Igorevna Borisova ◽  
Diana Yuzbekova ◽  
Anna Mogucheva
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Brittle Fracture ◽  
Fracture Surface ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Fine Grained ◽  
Angular Pressing ◽  
Different Temperatures ◽  
Elongation To Failure

An Al-4.57Mg-0.35Mn-0.2Sc-0.09Zr (wt. %) alloy was studied in the fine-grained state obtaining after equal channel angular pressing. The mechanical behavior of alloy at the temperatures 173 K, 298 K and 348 K and at strain rate 1×10–3 s–1 is studied. Increase of the temperature testing from 173 K to 348 K decreases the yield stress by 80 MPa, the ultimate tensile strength by 60 MPa while elongation-to failure increases by a factor of 1.4. It was found that at temperatures of 298 and 173 K, the studied alloy mainly demonstrates the mode of ductile fracture, and at a temperature of 348 K the mechanism can be described as mixed ductile-brittle fracture. It was also established that of the studied alloy is the temperature dependence of the size of the dimples on the fracture surface. The formation of smaller dimples in the samples deformed at 298 K was observed.

High Strain Rate Superplasticity in a Zr and Sc Modified 7075 Aluminum Alloy Produced by ECAP

2008 ◽  
Vol 584-586 ◽  
pp. 164-169 ◽  
Author(s):  
Krystof Turba ◽  
Premysl Malek ◽  
Edgar F. Rauch ◽  
Miroslav Cieslar
Keyword(s):  
Aluminum Alloy ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Rate Sensitivity ◽  
7075 Aluminum Alloy ◽  
Fine Grained ◽  
Angular Pressing ◽  
Average Grain Size ◽  
Elongation To Failure

Equal-channel angular pressing (ECAP) at 443 K was used to introduce an ultra-fine grained (UFG) microstructure to a Zr and Sc modified 7075 aluminum alloy. Using the methods of TEM and EBSD, an average grain size of 0.6 1m was recorded after the pressing. The UFG microstructure remained very stable up to the temperature of 723 K, where the material exhibited high strain rate superplasticity (HSRSP) with elongations to failure of 610 % and 410 % at initial strain rates of 6.4 x 10-2 s-1 and 1 x 10-1 s-1, respectively. A strain rate sensitivity parameter m in the vicinity of 0.45 was observed at temperatures as high as 773 K. At this temperature, the material still reached an elongation to failure of 430 % at 2 x 10-2 s-1. These results confirm the stabilizing effect of the Zr and Sc additions on the UFG microstructure in a 7XXX series aluminum alloy produced by severe plastic deformation.

Tensile Properties and Fracture Behavior of SiCp/AC4CH Composite at Loading Velocities of up to 10m/s

2004 ◽  
Vol 449-452 ◽  
pp. 305-308
Author(s):  
Lei Wang ◽  
Toshiro Kobayashi ◽  
Chun Ming Liu
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Tensile Deformation ◽  
Optical Microscope ◽  
Fracture Elongation ◽  
Before And After

Tensile test at loading velocities up to 10 m·s-1(strain rate up to 3.2x102s-1) was carried out forr SiCp/AC4CH composite and AC4CH alloy. The microstructure of the composite before and after tensile deformation was carefully examined with both optical microscope and SEM. The experimental results demonstrated that the ultimate tensile strength (UTS) and yield strength (YS) increase with increasing loading velocity up to 10 m·s-1. Comparing with AC4CH alloy, the fracture elongation of the composite is sensitivity with the increasing strain rate. The YS of both the composite and AC4CH alloy shows more sensitive than that of the UTS with the increasing strain rate, especially in the range of strain rate higher than 102s-1.

Mechanical Properties and Fracture Study of Alumina Dispersion Hardened Copper-Based Nano-Composite at Elevated Temperatures

2013 ◽  
Vol 829 ◽  
pp. 583-588 ◽  
Author(s):  
Ali Dalirbod ◽  
Yahya A. Sorkhe ◽  
Hossein Aghajani
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Fracture Surface ◽  
Yield Strength ◽  
Elevated Temperatures ◽  
Tensile Tests ◽  
Testing Temperature ◽  
Optical Microscope ◽  
Tensile Fracture ◽  
Different Temperatures

Alumina dispersion hardened copper-base composite was fabricated by internal oxidation method. The high temperature tensile fracture of Cu-Al2O3 composite was studied and tensile strengths were determined at different temperatures of 600, 680 and 780 °C. Microstructure was investigated by means of optical microscope and field emission scanning electron microscope (FESEM) with energy dispersive spectroscopy (EDS). Results show that, ultimate tensile strength and yield strength of copper alumina nanocomposite decrease slowly with increasing temperature. The yield strength reaches 119 MPa and ultimate tensile strength reaches 132 MPa at 780 °C. Surface fractography shows a dimple-type fracture on the fracture surface of the tensile tests where dimple size increases with increasing testing temperature and in some regions brittle fracture characteristics could be observed in the fracture surface.

Microstructure and Mechanical Property of an ECAP Processed Al-Mg2Si In Situ Composite by Using a Combined Route

2011 ◽  
Vol 194-196 ◽  
pp. 1720-1723 ◽  
Author(s):  
Li Ping Bian ◽  
Wei Liang ◽  
Wen Li Zhang
Keyword(s):  
Mechanical Property ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Angular Pressing ◽  
Elongation To Failure ◽  
Microstructure And Mechanical Property ◽  
Al Matrix

Microstructure and mechanical property of a hypoeutectic Al-Mg2Si composite processed by equal channel angular pressing up to eight passes in a combined route 2A+4BA+2A were investigated. The results show that the initial developed eutectic Mg2Si was significantly refined into submicrometer-scale particles and distributed homogeneously in the Al matrix, which together with the refinement of Al matrix leads to a much higher ductility with the elongation to failure up to 24% and a significantly enhanced ultimate tensile strength of 284MPa in the processed composite, increased by 2300% and 70%, respectively, compared to those in its as-cast counterpart.

scholarly journals The Influence of Microstructure on the Mechanical Properties and Fracture Behavior of Medium Mn Steels at Different Strain Rates

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4228 ◽  
Author(s):  
Zheng Wang ◽  
Juanping Xu ◽  
Yu Yan ◽  
Jinxu Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Total Elongation ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Car Crash ◽  
Δ Ferrite

The primary task of automotive industry materials is to guarantee passengers’ safety during a car crash. To simulate a car crash, the influence of strain rates on mechanical properties and fracture behavior of medium Mn steels with different Si content (0Si without δ-ferrite and 0.6Si with about 20% δ-ferrite) was conducted using the uniaxial tensile test. The results show that ultimate tensile strength is higher, whereas total elongation is lower in 0Si than in 0.6Si. As the strain rate increases, ultimate tensile strength and total elongation decrease in both 0Si and 0.6Si; nonetheless, total elongation of 0.6Si decreases faster. Meanwhile, the area reduction of 0.6Si increases as the strain rate increases. The microcrack′s number on a rolling direction (RD)-transverse direction (TD) surface is considerably increased; nonetheless, the microcrack′s size is restrained in 0.6Si compared with 0Si. Microcracks start at γ(α′)/α-ferrite interfaces in both 0Si and 0.6Si, whereas little nucleation sites have also been found at (γ(α′)+α-ferrite)/δ-ferrite boundaries in 0.6Si. Meanwhile, δ-ferrite reveals a higher capacity for microcrack arrest. As the strain rate decreases, increased lower crack growth results in fine and even dimples on fractographs with abundant second cracks on fractographs; meanwhile, the small microcrack′s number increases, while the large microcrack′s number decreases on an RD-TD surface.

scholarly journals Fracture behavior of twin induced ultra-fine grained ZK61 magnesium alloy under high strain rate compression

2019 ◽  
Vol 8 (4) ◽  
pp. 3475-3486 ◽  
Author(s):  
Abdul Malik ◽  
Wang Yangwei ◽  
Cheng Huanwu ◽  
Muhammad Abubaker Khan ◽  
Faisal Nazeer ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
High Strain Rate ◽  
Strain Rate ◽  
Fracture Behavior ◽  
High Strain ◽  
Fine Grained ◽  
Strain Rate Compression

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

Tensile Ductility of Ultra-Fine Grained Copper at High Strain Rate

2010 ◽  
Vol 160-162 ◽  
pp. 260-266 ◽  
Author(s):  
Tao Suo ◽  
Kui Xie ◽  
Yu Long Li ◽  
Feng Zhao ◽  
Qiong Deng
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Testing Machine ◽  
Coarse Grained ◽  
Dislocation Dynamic ◽  
Pressing Method ◽  
Fine Grained ◽  
Angular Pressing ◽  
Split Hopkinson

In this paper, ultra-fine grained copper fabricated by equal channel angular pressing method and annealed coarse grained copper were tensioned under both quasi-static and dynamic loading conditions using an electronic universal testing machine and the split Hopkinson tension bar respectively. The rapture surface of specimen was also observed via a Scanning Electron Microscope (SEM). The experimental results show that the ductility of polycrystalline copper decreases remarkably due to the grain refinement. However, with the increase of applied strain rate, ductility of the UFG-Cu is enhanced. The fracture morphologies also give the evidence of enhanced ductility of UFG-Cu at high strain rate. It is believed the enhanced ductility of UFG materials at high strain rate can be attributed to the restrained dislocation dynamic recovery.

Anisotropic Mechanical Properties of Rapid Prototyping Parts Fabricated by Stereolithography

2021 ◽  
Vol 13 (9) ◽  
pp. 1812-1819
Author(s):  
Na-Na Yang ◽  
Hao-Rui Liu ◽  
Ning Mi ◽  
Qi Zhou ◽  
Li-Qun He ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Brittle Fracture ◽  
Fracture Surface ◽  
Elongation At Break ◽  
Build Orientation ◽  
Range Distribution ◽  
Anisotropic Mechanical Properties ◽  
Orientation Experiment

Stereolithography (SLA)-manufactured parts behave with anisotropic properties due to the varying interface orientations generated by the layer-based manufacturing process. Part build orientation is a very important factor of anisotropic mechanical properties. In this paper, the build orientation experiment was designed to study the anisotropic behaviour of the mechanical properties of the SLA parts based on the orientation relationship between the force and the layer. The results show that there are obvious brittle characteristics on the fracture surface of the specimens and microcracks perpendicular to the direction of the layer distributed on the side of the fracture. The mechanical properties under brittle fracture have different degrees of sensitivity to the build orientation. Among all the build orientations, whether a specimen is built flat or on an edge shows obvious difference in tensile strength, and the relative range distribution reaches 35%. The changes in elastic modulus and the elongation at break are the most obvious in different angles relative to the XY plane, and the relative range distribution reaches 62% and 56% respectively. In all the build orientations designed, the tensile strength is the largest when it is placed on the edge at 0° with Y-axis in the XY plane, the elastic modulus is the largest when it was placed vertically, and the elongation at break is the largest when it is placed flat at 45° with Y-axis in the XY plane.

Thermal Stability of Mechanical Properties of Copper after Equal-Channel Angular Pressing

2008 ◽  
Vol 584-586 ◽  
pp. 960-965 ◽  
Author(s):  
Tamara Kravchenko ◽  
Alexander Korshunov ◽  
Natalia Zhdanova ◽  
Lev Polyakov ◽  
Irina Kaganova
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Chemical Composition ◽  
Yield Strength ◽  
Equal Channel Angular Pressing ◽  
Angular Pressing ◽  
Different Temperatures ◽  
Thermal Stability Of

Annealed oxygen-free and tough-pitch copper samples have been processed by equalchannel angular pressing (ECAP) by route BC. The samples included 8 x 8 mm section pieces and a 40 mm diameter bar. Thermal stability was assessed based on the changes in the standard mechanical properties (conventional yield strength, tensile strength, elongation, proportional elongation and contraction) after annealing at different temperatures for 1 hour. Thermal stability of the same grade of material has been found to be different for different batches and to depend on the structural conditions of deformed material. The zone of thermal stability for copper of the two grades of interest does not depend on the material’s chemical composition.

Sign in / Sign up

Export Citation Format

Share Document