A Method to Correct Indirect Strain Measurements in Laboratory Uniaxial and Triaxial Compressive Strength Tests

2021 ◽  
Author(s):  
L. R. Alejano ◽  
X. Estévez-Ventosa ◽  
M. A. González-Fernández ◽  
G. Walton ◽  
I. G. West ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Strain Measurements ◽  
Triaxial Compressive Strength ◽  
Strength Tests

scholarly journals Determination of Mechanical Properties of Altered Dacite by Laboratory Methods

Minerals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 813
Author(s):  
Veljko Rupar ◽  
Vladimir Čebašek ◽  
Vladimir Milisavljević ◽  
Dejan Stevanović ◽  
Nikola Živanović
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Rock Mass ◽  
Uniaxial Compressive Strength ◽  
Rock Material ◽  
Strength Parameter ◽  
Gradual Transition ◽  
Strength Parameters ◽  
Triaxial Compressive Strength ◽  
Heterogeneous Rock

This paper presents a methodology for determining the uniaxial and triaxial compressive strength of heterogeneous material composed of dacite (D) and altered dacite (AD). A zone of gradual transition from altered dacite to dacite was observed in the rock mass. The mechanical properties of the rock material in that zone were determined by laboratory tests of composite samples that consisted of rock material discs. However, the functional dependence on the strength parameter alteration of the rock material (UCS, intact UCS of the rock material, and mi) with an increase in the participation of “weaker” rock material was determined based on the test results of uniaxial and triaxial compressive strength. The participation of altered dacite directly affects the mode and mechanism of failure during testing. Uniaxial compressive strength (σciUCS) and intact uniaxial compressive strength (σciTX) decrease exponentially with increased AD volumetric participation. The critical ratio at which the uniaxial compressive strength of the composite sample equals the strength of the uniform AD sample was at a percentage of 30% AD. Comparison of the obtained exponential equation with practical suggestions shows a good correspondence. The suggested methodology for determining heterogeneous rock mass strength parameters allows us to determine the influence of rock material heterogeneity on the values σciUCS, σciTX, and constant mi. Obtained σciTX and constant mi dependences define more reliable rock material strength parameter values, which can be used, along with rock mass classification systems, as a basis for assessing rock mass parameters. Therefore, it is possible to predict the strength parameters of the heterogeneous rock mass at the transition of hard (D) and weak rock (AD) based on all calculated strength parameters for different participation of AD.

Measurement of high-alumina cement-calcium carbonate reactions using DTA

Clay Minerals ◽  
1984 ◽  
Vol 19 (5) ◽  
pp. 857-864 ◽  
Author(s):  
H. G. Midgley
Keyword(s):  
Compressive Strength ◽  
Calcium Carbonate ◽  
High Alumina ◽  
Curing Time ◽  
Lower Strength ◽  
Alumina Cement ◽  
High Alumina Cement ◽  
Strength Tests ◽  
The Stability

AbstractHydrating high-alumina cement will react with calcium carbonate to form the complex mineral calcium carboaluminate hydrate, 3CaO.Al2O3.CaCO3.12H2O. This mineral is reported to be capable of providing strength in concrete and so may provide an alternative to the minerals normally found in the hydration of high-alumina cement, which may under certain conditions convert to other minerals with a loss in strength. Some doubt has been cast on the stability of calcium carboaluminate hydrate and it has been found that in hydrated high-alumina cement, calcium carboaluminate hydrate decomposes at temperatures in excess of 60°C. Cube compressive strength tests on high-alumina cement and high-alumina cement-calcium carbonate pastes have shown that the latter have a lower strength than pastes made with high-alumina cement alone. When cured at 50°C the high-alumina cement-calcium carbonate pastes show a loss in strength with curing time. Cements made with the high-alumina cement-calcium carbonate mixture always have a lower strength than those made with high-alumina cement alone and so no advantage is gained from their use.

scholarly journals Assessment of the mechanical properties of glass ionomer cements for orthodontic cementation

2012 ◽  
Vol 17 (6) ◽  
pp. 154-159 ◽  
Author(s):  
Marcel M. Farret ◽  
Eduardo Martinelli de Lima ◽  
Eduardo Gonçalves Mota ◽  
Hugo Mitsuo S. Oshima ◽  
Gabriela Maguilnik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Resin Modified Glass Ionomer ◽  
Strength Tests ◽  
Diametral Tensile Strength

OBJECTIVE: To evaluate the mechanical properties of three glass ionomers cements (GICs) used for band cementation in Orthodontics. METHODS: Two conventional glass ionomers (Ketac Cem Easy mix/3M-ESPE and Meron/Voco) and one resin modified glass ionomer (Multi-cure Glass ionomer/3M-Unitek) were selected. For the compressive strength and diametral tensile strength tests, 12 specimens were made of each material. For the microhardness test 15 specimens were made of each material and for the shear bond strength tests 45 bovine permanent incisors were used mounted in a self-cure acrylic resin. Then, band segments with a welded bracket were cemented on the buccal surface of the crowns. For the mechanical tests of compressive and diametral tensile strength and shear bond strength a universal testing machine was used with a crosshead speed of 1,0 mm/min and for the Vickers microhardness analysis tests a Microdurometer was used with 200 g of load during 15 seconds. The results were submitted to statistical analysis through ANOVA complemented by Tukey's test at a significance level of 5%. RESULTS: The results shown that the Multi-Cure Glass Ionomer presented higher diametral tensile strength (p < 0.01) and compressive strength greater than conventional GICs (p = 0.08). Moreover, Ketac Cem showed significant less microhardness (p < 0.01). CONCLUSION: The resin-modified glass ionomer cement showed high mechanical properties, compared to the conventional glass ionomer cements, which had few differences between them.

scholarly journals Study on Strength Characteristics of Solidified Contaminated Soil under Freeze-Thaw Cycle Conditions

2018 ◽  
Vol 2018 ◽  
pp. 1-5 ◽  
Author(s):  
Qiang Wang ◽  
Jinyang Cui
Keyword(s):  
Electron Microscopy ◽  
Compressive Strength ◽  
Contaminated Soils ◽  
Unconfined Compressive Strength ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Strength Tests ◽  
Freeze Thaw Cycle ◽  
Microcosmic Mechanism ◽  
Scanning Electron

Cement solidification/stabilization is a commonly used method for the remediation of contaminated soils. The stability characteristics of solidified/stabilized contaminated soils under freeze-thaw cycle are very important. A series of tests, which include unconfined compressive strength tests, freeze-thaw cycle tests, and scanning electron microscopy (SEM) tests, are performed to study the variation law of strength characteristics and microstructure. It aims at revealing the microcosmic mechanism of solidified/stabilized Pb2+ contaminated soils with cement under freeze-thaw cycle. The results show that the unconfined compressive strength of the contaminated soils significantly improved with the increase of the cement content. The unconfined compressive strength of stabilized contaminated soils first increases with the increase of times of freeze-thaw cycle, and after reaching the peak, it decreases with the increase of times of freeze-thaw cycle. The results of the scanning electron microscopy tests are consistent with those of the unconfined compressive strength tests. This paper also reveals the microcosmic mechanism of the changes in engineering of the stabilized contaminated soils under freeze-thaw cycle.

Isothermal Fatigue Behavior and Damage Modeling of a High Temperature Woven PMC

1999 ◽  
Vol 122 (1) ◽  
pp. 62-68 ◽  
Author(s):  
A. L. Gyekenyesi
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Fatigue Behavior ◽  
Stiffness Degradation ◽  
Fatigue Properties ◽  
Residual Compressive Strength ◽  
Stiffness Reduction ◽  
Fatigue Damage Accumulation ◽  
Strength Tests

This study focuses on the fully reversed fatigue behavior exhibited by a carbon fiber/polyimide resin woven laminate at room and elevated temperatures. Nondestructive video edge view microscopy and destructive sectioning techniques were used to study the microscopic damage mechanisms that evolved. The elastic stiffness was monitored and recorded throughout the fatigue life of the coupon. In addition, residual compressive strength tests were conducted on fatigue coupons with various degrees of damage as quantified by stiffness reduction. Experimental results indicated that the monotonic tensile properties were only minimally influenced by temperature, while the monotonic compressive and fully reversed fatigue properties displayed greater reductions due to the elevated temperature. The stiffness degradation, as a function of cycles, consisted of three stages; a short-lived high degradation period, a constant degradation rate segment covering the majority of the life, and a final stage demonstrating an increasing rate of degradation up to failure. Concerning the residual compressive strength tests at room and elevated temperatures, the elevated temperature coupons appeared much more sensitive to damage. At elevated temperatures, coupons experienced a much larger loss in compressive strength when compared to room temperature coupons with equivalent damage. The fatigue damage accumulation law proposed for the model incorporates a scalar representation for damage, but admits a multiaxial, anisotropic evolutionary law. The model predicts the current damage (as quantified by residual stiffness) and remnant life of a composite that has undergone a known load at temperature. The damage/life model is dependent on the applied multiaxial stress state as well as temperature. Comparisons between the model and data showed good predictive capabilities concerning stiffness degradation and cycles to failure. [S0742-4795(00)01001-2]

POTENTIAL USE COCONUT MILK AS ALTERNATIVE TO ALKALI SOLUTION FOR GEOPOLYMER PRODUCTION

2016 ◽  
Vol 78 (11) ◽  
Author(s):  
Gahasan Fahim Huseien ◽  
Jahangir Mirza ◽  
Mohd Warid Hussin ◽  
Mohd Azreen Mohd Ariffin
Keyword(s):  
Compressive Strength ◽  
Alkali Solution ◽  
Coconut Milk ◽  
Fine Aggregate ◽  
Strength Tests ◽  
Last Stage ◽  
The Cost ◽  
The Impact ◽  
Potential Use ◽  
Control Samples

This work aims to verify the feasibility of utilizing coconut milk as the alkali activator solution in geopolymer production and the impact on mortar properties; geopolymer mortar is  still more expensive than ordinary Portland cement mortar simply because the cost of alkali solution. Coconut milk is extensively available in Malaysia and very rich in potassium and sodium. In this research, the coconut milk was used as alkali solution (100%) at first, and then replaced by NaOH, Na2SiO3 and in the last stage mixed with NaOH and Na2SiO3 at 50%. Normal solution component of Na2SiO3 and NaOH with 8 M, and used as control samples. Binder to fine aggregate (B:A) and solution to binder (S:B) ratios were fixed at 1.5 and 0.30 respectively. Multi blend binder based geopolymer mortar are used in this study. The samples were cured with different conditions, cured at room temperature and oven temperature of 60 and 90°C. Compressive strength tests were carried out to determine the properties of hardened mortar. The samples prepared with coconut milk showed low compressive strength as compared to control samples, The results demonstrated that using coconut milk as alternative to alkali solution in geopolymer industry is not a viable option.

scholarly journals Examining Polyethylene Terephthalate (PET) as Artificial Coarse Aggregates in Concrete

2020 ◽  
Vol 6 (12) ◽  
pp. 2416-2424
Author(s):  
Erniati Bachtiar ◽  
Mustaan Mustaan ◽  
Faris Jumawan ◽  
Meldawati Artayani ◽  
Tahang Tahang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Coarse Aggregates ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Recycled Polyethylene

This study aims to examine the effect of recycled Polyethylene Terephthalate (PET) artificial aggregate as a substitute for coarse aggregate on the compressive strength and flexural strength, and the volume weight of the concrete. PET plastic waste is recycled by heating to a boiling point of approximately 300°C. There are five variations of concrete mixtures, defined the percentage of PET artificial aggregate to the total coarse aggregate, by 0, 25, 50, 75 and 100%. Tests carried out on fresh concrete mixtures are slump, bleeding, and segregation tests. Compressive and flexural strength tests proceeded based on ASTM 39/C39M-99 and ASTM C293-79 standards at the age of 28 days. The results showed that the use of PET artificial aggregate could improve the workability of the concrete mixture. The effect of PET artificial aggregate as a substitute for coarse aggregate on the compressive and flexural strength of concrete is considered very significant. The higher the percentage of PET plastic artificial aggregate, the lower the compressive and flexural strength, and the volume weight, of the concrete. Substitution of 25, 50, 75 and 100% of PET artificial aggregate gave decreases in compressive strength of 30.06, 32.39, 41.73 and 44.06% of the compressive strength of the standard concrete (18.20 MPa), respectively. The reductions in flexural strength were by respectively 19.03, 54.50, 53.95 and 61.00% of the standard concrete's flexural strength (3.59 MPa). The reductions in volume weight of concrete were by respectively 8.45, 17.71, 25.07 and 34.60% of the weight of the standard concrete volume of 2335.4 kg/m3 Doi: 10.28991/cej-2020-03091626 Full Text: PDF

Effects of 0-30% Wood Ashes as a Substitute of Cement on the Strength of Concretes

2022 ◽  
Author(s):  
Theodore Gautier Bikoko ◽  
Jean Claude Tchamba ◽  
Valentine Yato Katte ◽  
Divine Kum Deh
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Greenhouse Gases ◽  
Negative Influence ◽  
Wood Ash ◽  
The Other ◽  
Other Hand ◽  
Strength Tests ◽  
Compressive Strength Of Concrete ◽  
Curing Age

To fight against the high cost and the increasing scarcity of cement and at the same time to reduce the CO2 greenhouse gases emission associated with the production of Portland cement, two types of wood ashes as a substitute of cement in the production of concretes were investigated. In this paper, we substituted cement by two types of species of wood ashes namely, avocado and eucalyptus ashes following the proportions ranging from 0% to 30 % on one hand, and on the other hand, we added these two types of species of wood ashes namely, avocado and eucalyptus ashes following the proportions ranging from 0% to 10 % by weight of cement in the concrete samples. After 7, 14 and 28 days of curing, compressive strength tests were conducted on these concrete samples. The findings revealed that using wood ashes as additives/admixtures or as a substitute of cement in the production/manufacturing of concrete decreased the compressive strength of concrete. Hence, it can be said that wood ash has a negative influence on the strength of concrete. At three percent (3%) and ten percent (10%) of addition, the wood ash from eucalyptus specie offers better resistance compared to the wood ash from avocado specie, whereas at five percent (5%) of addition, the wood ash from avocado specie offers better resistance compared to the wood ash from eucalyptus specie. At thirty percent (30%) of substitution, the wood ash from eucalyptus specie offers better resistance compared to the wood ash from avocado specie. The compressive strengths increase with the increase of curing age.

scholarly journals Size Effect in Compressive Strength Tests of Cored Specimens of Lightweight Aggregate Concrete

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1187 ◽  
Author(s):  
Lucyna Domagała
Keyword(s):  
Compressive Strength ◽  
Scale Effect ◽  
Lightweight Aggregate ◽  
Normal Weight ◽  
Cement Matrix ◽  
Lightweight Aggregate Concrete ◽  
Core Diameter ◽  
Aggregate Concrete ◽  
Normal Weight Concrete ◽  
Strength Tests

The aim of this paper is to discuss the unrecognized problem of the scale effect in compressive strength tests determined for cored specimens of lightweight aggregate concrete (LWAC) against the background of available data on the effect for normal-weight concrete (NWAC). The scale effect was analyzed taking into consideration the influence of slenderness (λ = 1.0, 1.5, 2.0) and diameter (d = 80, 100, 125, and 150 mm) of cored specimens, as well as the type of lightweight aggregate (expanded clay and sintered fly ash) and the type of cement matrix (w/c = 0.55 and 0.37). The analysis of the results for four lightweight aggregate concretes revealed no scale effect in compressive strength tests determined on cored specimens. Neither the slenderness, nor the core diameter seemed to affect the strength results. This fact should be explained by the considerably better structural homogeneity of the tested lightweight concretes in comparison to normal-weight ones. Nevertheless, there were clear differences between the results obtained on molded and cored specimens of the same shape and size.

Sign in / Sign up

Export Citation Format

Share Document