scholarly journals Development of particle migration in pressure-driven flow of a Brownian suspension

2007 ◽  
Vol 581 ◽  
pp. 437-451 ◽  
Author(s):  
DENIS SEMWOGERERE ◽  
JEFFREY F. MORRIS ◽  
ERIC R. WEEKS
Keyword(s):  
Flow Rate ◽  
Colloidal Particles ◽  
Volume Fraction ◽  
Rectangular Cross Section ◽  
Sample Volume ◽  
Particle Migration ◽  
Entrance Length ◽  
Uniform Steady State ◽  
Monodisperse Suspensions ◽  
Pressure Driven Flow

An experimental investigation into the influence of Brownian motion on shear-induced particle migration of monodisperse suspensions of micrometre-sized colloidal particles is presented. The suspension is pumped through a 50 μm × 500 μm rectangular cross-section glass channel. The experiments are characterized chiefly by the sample volume fraction (φ = 0.1 − 0.4), and the flow rate expressed as the Péclet number (Pe = 10 − 400). For each experiment we measure the entrance length, which is the distance from the inlet of the channel required for the concentration profile to develop to its non-uniform steady state. The entrance length increases strongly with increasing Pe for Pe ≪ 100, in marked contrast to non-Brownian flows for which the entrance length is flow-rate independent. For larger Pe, the entrance length reaches a constant value which depends on the other experimental parameters. Additionally, the entrance length decreases with increasing φ; this effect is strongest for low φ. Modelling of the migration based on spatial variation of the normal stresses due to the particles captures the primary features observed in the axial evolution over a range of Pe and φ.

scholarly journals Enrichment and Purification of Aucubin from Eucommia ulmoides Ionic Liquid Extract Using Macroporous Resins

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1758 ◽  
Author(s):  
Xinyu Yang ◽  
Mengxia Wei ◽  
Hao Tian ◽  
Tingting Liu ◽  
Lei Yang
Keyword(s):  
Ionic Liquid ◽  
Flow Rate ◽  
Volume Fraction ◽  
Sample Volume ◽  
Eucommia Ulmoides ◽  
High Concentration ◽  
Desorption Process ◽  
Operational Conditions ◽  
Macroporous Resins ◽  
Washing Process

Aiming to address the shortcomings of high-concentration ethanol or methanol extraction solutions that need to be diluted and concentrated prior to use in conventional macroporous resin adsorption approaches, an efficient approach for enrichment and purification of aucubin from the ionic liquid extraction solution of samaras of Eucommia ulmoides was proposed. Among the nine kinds of macroporous resins investigated, the HPD850 resin was found to be the most suitable. Equilibrium adsorption tests were investigated and found to be better fitted by the Langmuir isotherm model. After the dynamic tests on a column packed with HPD850, the optimum operational conditions were as follows: for the absorption process, an initial aucubin concentration of 9.87 mg/L, a sample volume of 13 bed volumes (BV), and a flow rate of 2 BV/h; for the water washing process, 5 BV of deionized water and a flow rate of 3 BV/h; for the ethanol desorption process, a 10–80% ethanol volume fraction as the eluent, 2 BV for each ethanol volume fraction, and a flow rate of 3 BV/h. The 40–80% ethanol volume fraction eluent was collected and concentrated to produce the final products, resulting in an aucubin purity and recovery of 79.41% and 72.92%, respectively.

Amorphous-to-nanocrystalline transition in silicon thin films by hydrogen diluted silane using PE-CVD method

2020 ◽  
Vol 13 ◽  
Author(s):  
Ashok Jadhavar ◽  
Vidya Doiphode ◽  
Ajinkya Bhorde ◽  
Yogesh Hase ◽  
Pratibha Shinde ◽  
...  
Keyword(s):  
Flow Rate ◽  
Volume Fraction ◽  
Defect Density ◽  
Hydrogen Flow Rate ◽  
Spectroscopy Analysis ◽  
Deposition Parameter ◽  
Hydrogen Flow ◽  
Cvd Method ◽  
Silicon Thin Films ◽  
Increasing Trend

: Herein, we report effect of variation of hydrogen flow rate on properties of Si:H films synthesized using PE-CVD method. Raman spectroscopy analysis show increase in crystalline volume fraction and crystallite size implying that hydrogen flow in PECVD promote the growth of crystallinity in nc-Si:H films with an expense of reduction in deposition rate. FTIR spectroscopy analysis indicates that hydrogen content in the film increases with increase in hydrogen flow rate and hydrogen is predominantly incorporated in Si-H2 and (Si-H2)n bonding configuration. The optical band gap determined using E04 method and Tauc method (ETauc) show increasing trend with increase in hydrogen flow rate and E04 is found higher than ETauc over the entire range of hydrogen flow rate studied. We also found that the defect density and Urbach energy also increases with increase in hydrogen flow rate. Photosensitivity (Photo /Dark) decreases from  103 to  1 when hydrogen flow rate increased from 30 sccm to 100 sccm and can attributed to amorphous-to-nanocrystallization transition in Si:H films. The results obtained from the present study demonstrated that hydrogen flow rate is an important deposition parameter in PE-CVD to synthesize nc-Si:H films.

scholarly journals Effect of the Gas Volume Fraction on the Pressure Load of the Multiphase Pump Blade

Processes ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 650
Author(s):  
Guangtai Shi ◽  
Dandan Yan ◽  
Xiaobing Liu ◽  
Yexiang Xiao ◽  
Zekui Shu
Keyword(s):  
Flow Rate ◽  
Static Pressure ◽  
Volume Fraction ◽  
Pump Impeller ◽  
Impeller Blade ◽  
Multiphase Pump ◽  
Pressure Load ◽  
Gas Volume Fraction ◽  
Power Capability ◽  
Gas Volume

The gas volume fraction (GVF) often changes from time to time in a multiphase pump, causing the power capability of the pump to be increasingly affected. In the purpose of revealing the pressure load characteristics of the multiphase pump impeller blade with the gas-liquid two-phase case, firstly, a numerical simulation which uses the SST k-ω turbulence model is verified with an experiment. Then, the computational fluid dynamics (CFD) software is employed to investigate the variation characteristics of static pressure and pressure load of the multiphase pump impeller blade under the diverse inlet gas volume fractions (IGVFs) and flow rates. The results show that the effect of IGVF on the head and hydraulic efficiency at a small flow rate is obviously less than that at design and large flow rates. The static pressure on the blade pressure side (PS) is scarcely affected by the IGVF. However, the IGVF has an evident effect on the static pressure on the impeller blade suction side (SS). Moreover, the pump power capability is descended by degrees as the IGVF increases, and it is also descended with the increase of the flow rate at the impeller inlet. Simultaneously, under the same IGVF, with the increase of the flow rate, the peak value of the pressure load begins to gradually move toward the outlet and its value from hub to shroud is increased. The research results have important theoretical significance for improving the power capability of the multiphase pump impeller.

Laser-Induced Pretransitional Ordering And Nonlinear Optical Properties Of Rigid-Rod Polymer Suspensions

1993 ◽  
Vol 328 ◽  
Author(s):  
Boris E. Vugmeister ◽  
Michelle S. Malcuit ◽  
John C. Kralik ◽  
Colleen Stevens
Keyword(s):  
Phase Transition ◽  
Colloidal Particles ◽  
Volume Fraction ◽  
Orientational Order ◽  
Critical Value ◽  
Orientational Relaxation ◽  
First Order ◽  
First Order Phase Transition ◽  
Rigid Rod ◽  
First Order Phase

ABSTRACTWe investigate the pretransitional behavior in laser-induced alignment of rigid rod-like polytetraflouroethylene (PTFE) suspensions. Using a laser-induced birefringence experiment, we measure both the orientational order parameter and the orientational relaxation time. We find that both increase as the volume fraction of colloidal particles approaches the critical value for the isotropic-nematic phase transition. Experimental results are compared with theory which takes into account the possibility of a first-order phase transition induced by a laser electric field.

scholarly journals Steady electrodiffusion in hydrogel-colloid composites: macroscale properties from microscale electrokinetics

2010 ◽  
Vol 82 (1) ◽  
pp. 69-86
Author(s):  
Reghan J. Hill
Keyword(s):  
Membrane Potential ◽  
Electrostatic Potential ◽  
Colloidal Particles ◽  
Electrolyte Concentration ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Solid Volume Fraction ◽  
Electrical Current ◽  
Inclusion Size ◽  
Particle Volume

A rigorous microscale electrokinetic model for hydrogel-colloid composites is adopted to compute macroscale profiles of electrolyte concentration, electrostatic potential, and hydrostatic pressure across membranes that separate electrolytes with different concentrations. The membranes are uncharged polymeric hydrogels in which charged spherical colloidal particles are immobilized and randomly dispersed with a low solid volume fraction. Bulk membrane characteristics and performance are calculated from a continuum microscale electrokinetic model (Hill 2006b, c). The computations undertaken in this paper quantify the streaming and membrane potentials. For the membrane potential, increasing the volume fraction of negatively charged inclusions decreases the differential electrostatic potential across the membrane under conditions where there is zero convective flow and zero electrical current. With low electrolyte concentration and highly charged nanoparticles, the membrane potential is very sensitive to the particle volume fraction. Accordingly, the membrane potential - and changes brought about by the inclusion size, charge and concentration - could be a useful experimental diagnostic to complement more recent applications of the microscale electrokinetic model for electrical microrheology and electroacoustics (Hill and Ostoja-Starzewski 2008, Wang and Hill 2008).

scholarly journals Experimental Investigation of a Rectangular Airlift Pump

2010 ◽  
Vol 2010 ◽  
pp. 1-5 ◽  
Author(s):  
I. I. Esen
Keyword(s):  
Experimental Investigation ◽  
Cross Section ◽  
Flow Rate ◽  
Liquid Flow ◽  
Liquid Flow Rate ◽  
Rectangular Cross Section ◽  
Hydraulic Performance ◽  
Experimental Program ◽  
Empirical Equations ◽  
Airlift Pump

Hydraulic performance of an airlift pump having a rectangular cross-section 20 mm × 80 mm was investigated through an experimental program. The pump was operated at six different submergence ratios and the liquid flow rate was measured at various flowrates of air injected. The effectiveness of the pump, defined as the ratio of the mass of liquid pumped to the mass of air injected, was determined as a function of the mass of air injected for different submergence ratios. Results obtained were compared with those for circular airlift pumps using an analytical model for circular pumps. Effectiveness of the rectangular airlift pump was observed to be comparable to that of the circular pumps. Hydraulic performance of the rectangular airlift pump investigated was then described by a set of semilogarithmic empirical equations.

scholarly journals Aggregation kinetics of irreversible patches coupled with reversible isotropic interaction leading to chains, bundles and globules

2018 ◽  
Vol 90 (6) ◽  
pp. 1085-1098 ◽  
Author(s):  
Isha Malhotra ◽  
Sujin B. Babu
Keyword(s):  
Self Assembly ◽  
Patch Size ◽  
Colloidal Particles ◽  
Volume Fraction ◽  
Interaction Strength ◽  
Colloidal System ◽  
Angle Distribution ◽  
Volume Fractions ◽  
Low Volume ◽  
A Chain

Abstract In the present study we are performing simulation of simple model of two patch colloidal particles undergoing irreversible diffusion limited cluster aggregation using patchy Brownian cluster dynamics. In addition to the irreversible aggregation of patches, the spheres are coupled with isotropic reversible aggregation through the Kern–Frenkel potential. Due to the presence of anisotropic and isotropic potential we have also defined three different kinds of clusters formed due to anisotropic potential and isotropic potential only as well as both the potentials together. We have investigated the effect of patch size on self-assembly under different solvent qualities for various volume fractions. We will show that at low volume fractions during aggregation process, we end up in a chain conformation for smaller patch size while in a globular conformation for bigger patch size. We also observed a chain to bundle transformation depending on the attractive interaction strength between the chains or in other words depending on the quality of the solvent. We will also show that bundling process is very similar to nucleation and growth phenomena observed in colloidal system with short range attraction. We have also studied the bond angle distribution for this system, where for small patches only two angles are more probable indicating chain formation, while for bundling at very low volume fraction a tail is developed in the distribution. While for the case of higher patch angle this distribution is broad compared to the case of low patch angles showing we have a more globular conformation. We are also proposing a model for the formation of bundles which are similar to amyloid fibers using two patch colloidal particles.

Effects of Fe3O4/Water Nanofluid on the Efficiency of a Curved Pipe

2019 ◽  
Vol 11 (4) ◽  
Author(s):  
Milad Kelidari ◽  
Ali Jabari Moghadam
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Volume Concentration ◽  
Volume Fraction ◽  
Working Fluid ◽  
Radius Of Curvature ◽  
Dean Number ◽  
Curved Pipe ◽  
Overall Efficiency

Different-radius of curvature pipes are experimentally investigated using distilled water and Fe3O4–water nanofluid with two different values of the nanoparticle volume fraction as the working fluids. The mass flow rate is approximately varied from 0.2 to 0.7 kg/min (in the range of laminar flow); the wall heat flux is nearly kept constant. The experimental results reveal that utilizing the nanofluid increases the convection heat transfer coefficient and Nusselt number in comparison to water; these outcomes are also observed when the radius of curvature is decreased and/or the mass flow rate is increased (equivalently, a rise in Dean number). The resultant pressure gradient is, however, intensified by an increase in the volume concentration of nanoparticles and/or by a rise in Dean number. For any particular working fluid, there is an optimum mass flow rate, which maximizes the system efficiency. The overall efficiency can be introduced to include hydrodynamic as well as thermal characteristics of nanofluids in various geometrical conditions. For each radius of curvature, the same overall efficiency may be achieved for two magnitudes of nanofluid volume concentration.

scholarly journals Pressure-driven flow of suspensions: simulation and theory

1994 ◽  
Vol 275 ◽  
pp. 157-199 ◽  
Author(s):  
Prabhu R. Nott ◽  
John F. Brady
Keyword(s):  
Particle Velocity ◽  
Particle Migration ◽  
Channel Width ◽  
Stokesian Dynamics ◽  
Dynamic Simulations ◽  
Inhomogeneous Flow ◽  
Pressure Driven Flow ◽  
Energy Balances ◽  
Good Agreement ◽  
Pressure Driven

Dynamic simulations of the pressure-driven flow in a channel of a non-Brownian suspension at zero Reynolds number were conducted using Stokesian Dynamics. The simulations are for a monolayer of identical particles as a function of the dimensionless channel width and the bulk particle concentration. Starting from a homogeneous dispersion, the particles gradually migrate towards the centre of the channel, resulting in an homogeneous concentration profile and a blunting of the particle velocity profile. The time for achieving steady state scales as (H/a)3a/〈u〉, where H is the channel width, a the radii of the particles, and 〈u〉 the average suspension velocity in the channel. The concentration and velocity profiles determined from the simulations are in qualitative agreement with experiment.A model for suspension flow has been proposed in which macroscopic mass, momentum and energy balances are constructed and solved simultaneously. It is shown that the requirement that the suspension pressure be constant in directions perpendicular to the mean motion leads to particle migration and concentration variations in inhomogeneous flow. The concept of the suspension ‘temperature’ – a measure of the particle velocity fluctuations – is introduced in order to provide a nonlocal description of suspension behaviour. The results of this model for channel flow are in good agreement with the simulations.

The Influence of Major Diameter Solid Particle on the Double-Channel Pump Performance

2011 ◽  
Author(s):  
Yi Li ◽  
Qiaoling Cui ◽  
Zuchao Zhu ◽  
Zhaohui He ◽  
Baoling Cui
Keyword(s):  
Numerical Simulation ◽  
Flow Rate ◽  
Sliding Wear ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Particle Diameter ◽  
Wall Region ◽  
Impeller Outlet ◽  
Anticlockwise Direction ◽  
Double Channel

Based on mixture model, the numerical simulation of solid-liquid two-phase flow in a double channel pump (Specific speed ns = 81) was carried out. The effects of particle diameter, particle volume fraction and flow rate on solid volume concentration distribution, relative velocity distribution and abrasion characteristics were studied. The results reveal that in the impeller, more particles concentrate at the nut of the shaft end and the edge of the impeller outlet. So those regions are worn seriously. The abrasive types are sliding wear on the impeller outlet edge and impact wear on the nut respectively. In the wall of the volute, the concentrated areas of particles move round the anticlockwise direction when the mixture flow rate is larger. The reason is the mixture velocity is larger as the flow rate increases, and meanwhile the centrifugal force and gravity force are invariable. So the particles move round the impeller rotational direction consequently. In the volute, particles concentrate on the tongue and wall region, especially on the sections I, II, V and VII. So the areas are easily worn out. The abrasive type is the heavy sliding wear in the volute wall. Numerical simulation results are consistent with the actual situation. It follows that the calculating method is feasible.

Sign in / Sign up

Export Citation Format

Share Document