Al Compositional Profile In Algaas/Gaas Quantum Wells

1999 ◽  
Vol 5 (S2) ◽  
pp. 168-169
Author(s):  
D. Q. Cai ◽  
J. Zou ◽  
D. J. H. Cockayne.
Keyword(s):  
Fine Structure ◽  
Sample Preparation ◽  
Quantum Well ◽  
Quantum Wells ◽  
Ccd Camera ◽  
Bright Field ◽  
Compositional Profile ◽  
Set Up ◽  
Cleavage Method

The TEM thickness fringe method [1] was developed as a potential routine technique to determine compositional profiles in quantum well systems. This technique has the advantages that a) TEM sample preparation is simple and the experiment is easy to set up and b) thickness fringe profiles show fine structure which is sensitive to chemistry [2]. In this paper, we demonstrate the ability of the method to measure the chemical abruptness at the interface between two layers of different composition.90° wedge AlGaAs/GaAs TEM samples were prepared by the cleavage method, where the samples were cleaved along two orthogonal {110} planes. The samples were mounted on Cu grids and were investigated in a Philips EM430 TEM. Samples were orientated to the [100] direction precisely and bright-field images were acquired digitally using a CCD camera. Fig 1 shows an enlarged image of thickness fringes.Since the edges of samples are 90° wedges, the thickness at any point can be accurately determined and the fringe profile can be compared with fringe profiles calculated for a range of Al compositions.

Characterization of GaAs/AlGaAs quantum wells and quantum wires by chemical lattice imaging

1994 ◽  
Vol 52 ◽  
pp. 736-737
Author(s):  
A. Carlsson ◽  
J.-O. Malm ◽  
A. Gustafsson
Keyword(s):  
Quantum Well ◽  
Quantum Wells ◽  
Quantum Wires ◽  
Vapour Phase ◽  
Quantitative Information ◽  
Lattice Imaging ◽  
Vapour Phase Epitaxy ◽  
Metalorganic Vapour Phase Epitaxy ◽  
High Resolution Images

In this study a quantum well/quantum wire (QW/QWR) structure grown on a grating of V-grooves has been characterized by a technique related to chemical lattice imaging. This technique makes it possible to extract quantitative information from high resolution images.The QW/QWR structure was grown on a GaAs substrate patterned with a grating of V-grooves. The growth rate was approximately three monolayers per second without growth interruption at the interfaces. On this substrate a barrier of nominally Al0.35 Ga0.65 As was deposited to a thickness of approximately 300 nm using metalorganic vapour phase epitaxy . On top of the Al0.35Ga0.65As barrier a 3.5 nm GaAs quantum well was deposited and to conclude the structure an additional approximate 300 nm Al0.35Ga0.65 As was deposited. The GaAs QW deposited in this manner turns out to be significantly thicker at the bottom of the grooves giving a QWR running along the grooves. During the growth of the barriers an approximately 30 nm wide Ga-rich region is formed at the bottom of the grooves giving a Ga-rich stripe extending from the bottom of each groove to the surface.

Characterisation of multilayer materials using a position-sensitive atom probe

1990 ◽  
Vol 48 (4) ◽  
pp. 624-625
Author(s):  
RAD Mackenzie ◽  
G D W Smith ◽  
A. Cerezo ◽  
J A Liddle ◽  
CRM Grovenor ◽  
...  
Keyword(s):  
Quantum Well ◽  
Quantum Wells ◽  
Spatial Information ◽  
Chemical Vapour ◽  
Atom Probe ◽  
Organic Chemical ◽  
Growth Stages ◽  
Multiple Quantum ◽  
Quartz Wool ◽  
Position Sensitive

The position sensitive atom probe (POSAP), described briefly elsewhere in these proceedings, permits both chemical and spatial information in three dimensions to be recorded from a small volume of material. This technique is particularly applicable to situations where there are fine scale variations in composition present in the material under investigation. We report the application of the POSAP to the characterisation of semiconductor multiple quantum wells and metallic multilayers.The application of devices prepared from quantum well materials depends on the ability to accurately control both the quantum well composition and the quality of the interfaces between the well and barrier layers. A series of metal organic chemical vapour deposition (MOCVD) grown GaInAs-InP quantum wells were examined after being prepared under three different growth conditions. These samples were observed using the POSAP in order to study both the composition of the wells and the interface morphology. The first set of wells examined were prepared in a conventional reactor to which a quartz wool baffle had been added to promote gas intermixing. The effect of this was to hold a volume of gas within the chamber between growth stages, leading to a structure where the wells had a composition of GalnAsP lattice matched to the InP barriers, and where the interfaces were very indistinct. A POSAP image showing a well in this sample is shown in figure 1. The second set of wells were grown in the same reactor but with the quartz wool baffle removed. This set of wells were much better defined, as can be seen in figure 2, and the wells were much closer to the intended composition, but still with measurable levels of phosphorus. The final set of wells examined were prepared in a reactor where the design had the effect of minimizing the recirculating volume of gas. In this case there was again further improvement in the well quality. It also appears that the left hand side of the well in figure 2 is more abrupt than the right hand side, indicating that the switchover at this interface from barrier to well growth is more abrupt than the switchover at the other interface.

scholarly journals Asymmetric Ge/SiGe coupled quantum well modulators

Nanophotonics ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 1765-1773
Author(s):  
Yi Zhang ◽  
Jianfeng Gao ◽  
Senbiao Qin ◽  
Ming Cheng ◽  
Kang Wang ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Quantum Well ◽  
Quantum Wells ◽  
High Speed ◽  
Low Voltage ◽  
Extinction Ratio ◽  
High Frequency Response ◽  
Modulation Format ◽  
Silicon Photonic ◽  
Coupled Quantum Well

Abstract We design and demonstrate an asymmetric Ge/SiGe coupled quantum well (CQW) waveguide modulator for both intensity and phase modulation with a low bias voltage in silicon photonic integration. The asymmetric CQWs consisting of two quantum wells with different widths are employed as the active region to enhance the electro-optical characteristics of the device by controlling the coupling of the wave functions. The fabricated device can realize 5 dB extinction ratio at 1446 nm and 1.4 × 10−3 electrorefractive index variation at 1530 nm with the associated modulation efficiency V π L π of 0.055 V cm under 1 V reverse bias. The 3 dB bandwidth for high frequency response is 27 GHz under 1 V bias and the energy consumption per bit is less than 100 fJ/bit. The proposed device offers a pathway towards a low voltage, low energy consumption, high speed and compact modulator for silicon photonic integrated devices, as well as opens possibilities for achieving advanced modulation format in a more compact and simple frame.

Light Emission Properties of GaN-Based Double Heterostructures and Quantum Wells

1995 ◽  
Vol 395 ◽  
Author(s):  
D.A.S. Loeber ◽  
J.M. Redwing ◽  
N.G. Anderson ◽  
M.A. Tischler
Keyword(s):  
Quantum Well ◽  
Quantum Wells ◽  
Stimulated Emission ◽  
Pump Light ◽  
Band Edge Emission ◽  
Emission Characteristics ◽  
Nitrogen Laser ◽  
Edge Emission ◽  
Edge Luminescence ◽  
Double Heterostructures

ABSTRACTEdge emission characteristics of optically pumped GaN-AlGaN double heterostructures and quantum wells are examined. The samples, which were grown by metalorganic vapor phase epitaxy, are photoexcited with light from a pulsed nitrogen laser. The pump light is focused to a narrow stripe on the sample surface, oriented perpendicular to a cleaved edge, and the edge luminescence is collected and analyzed. We first compare emission characteristics of highly excited GaN-AlGaN double heterostructures grown simultaneously on SiC and sapphire substrates. Polarization resolved spectral properties of edge luminescence from both structures is studied as a function of pump intensity and excitation stripe length. Characteristics indicative of stimulated emission are observed, particularly in the sample grown on SiC. We then present results demonstrating laser emission from a GaN-AlGaN separate-confinement quantum-well heterostructure. At high pump intensities, band edge emission from the quantum well exhibits five narrow (∼1 Å) modes which are evenly spaced by 10Å to within the resolution of the spectrometer. This represents the first demonstration of laser action in a GaN-based quantum-well structure.

Thermoelectric Power in Quantum Confined Bismuth Under Classically Large Magnetic Field

1990 ◽  
Vol 216 ◽  
Author(s):  
Kamakhya P. Ghatak ◽  
S. N. Biswas
Keyword(s):  
Magnetic Field ◽  
Quantum Dots ◽  
Quantum Well ◽  
Film Thickness ◽  
Quantum Wells ◽  
Thermoelectric Power ◽  
Large Magnetic Field ◽  
Quantum Well Wires ◽  
Electron Dispersion ◽  
Theoretical Results

ABSTRACTIn this paper we studied the thermoelectric power under classically large magnetic field (TPM) in quantum wells (QWs), quantum well wires (QWWS) and quantum dots (QDs) of Bi by formulating the respective electron dispersion laws. The TPM increases with increasing film thickness in an oscillatory manner in all the cases. The TPM in QD is greatest and the least for quantum wells respectively. The theoretical results are in agreement with the experimental observations as reported elsewhere.

LINEAR AND NONLINEAR INTERSUBBAND OPTICAL ABSORPTION OF FINITE AND INFINITE SEMI-PARABOLIC QUANTUM WELLS

2011 ◽  
Vol 25 (07) ◽  
pp. 497-507 ◽  
Author(s):  
M. J. KARIMI ◽  
A. KESHAVARZ ◽  
A. POOSTFORUSH
Keyword(s):  
Refractive Index ◽  
Optical Properties ◽  
Optical Absorption ◽  
Quantum Well ◽  
Quantum Wells ◽  
Resonant Peak ◽  
Energy Eigenvalues ◽  
Finite Case ◽  
Infinite Case ◽  
Index Changes

In this work, the optical absorption coefficients and the refractive index changes for the infinite and finite semi-parabolic quantum well are calculated. Numerical calculations are performed for typical GaAs / Al x Ga 1-x As semi-parabolic quantum well. The energy eigenvalues and eigenfunctions of these systems are calculated numerically. Optical properties are obtained using the compact density matrix approach. Results show that the energy eigenvalues and the matrix elements of the infinite and finite cases are different. The calculations reveal that the resonant peaks of the optical properties of the finite case occur at lower values of the incident photon energy with respect to the infinite case. Results indicate that the maximum value of the refractive index changes for the finite case are greater than that of the infinite case. Our calculations also show that in contrast to the infinite case, the resonant peak value of the total absorption coefficient in the case of the finite well is a non-monotonic function of the semi-parabolic confinement frequency.

45° REFLECTOMETRY OF SEMICONDUCTOR QUANTUM WELLS

2001 ◽  
Vol 15 (17n19) ◽  
pp. 683-687
Author(s):  
A. SILVA-CASTILLO ◽  
F. PEREZ-RODRIGUEZ
Keyword(s):  
Quantum Well ◽  
Quantum Wells ◽  
Growth Direction ◽  
Angle Of Incidence ◽  
Near Surface ◽  
New Information ◽  
Difference Formula ◽  
Exciton Polaritons ◽  
The Difference ◽  
First Time

We have applied the 45° reflectometry for the first time to study exciton-polaritons in quantum wells. The 45° reflectometry is a new polarization-modulation technique, which is based on the measurement of the difference [Formula: see text] between the p-polarization reflectivity (Rp) and the squared s-polarization reflectivity [Formula: see text] at an angle of incidence of 45°. We show that [Formula: see text] spectra may provide qualitatively new information on the exciton-polariton modes in a quantum well. These optical spectra turn out to be very sensitive to the zeros of the dielectric function along the quantum-well growth direction and, therefore, allow to identify the resonances associated with the Z exciton-polariton mode. We demonstrate that 45° reflectometry could be a powerful tool for studying Z exciton-polariton modes in near-surface quantum wells, which are difficult to observe in simple spectra of reflectivity Rp

Modular automated bottom-up proteomic sample preparation for high-throughput applications v1

2021 ◽  
Author(s):  
Yan Chen ◽  
Nurgul Kaplan Lease ◽  
Jennifer Gin ◽  
Tad Ogorzalek ◽  
Paul D. Adams ◽  
...  
Keyword(s):  
Sample Preparation ◽  
High Throughput ◽  
Tryptic Digestion ◽  
Gram Negative Bacteria ◽  
Bottom Up ◽  
Preparation Methods ◽  
Gram Negative ◽  
E Coli ◽  
Protocol Development ◽  
Set Up

Manual proteomic sample preparation methods limit sample throughput and often lead to poor data quality when thousands of samples must be analyzed. Automated workflows are increasingly used to overcome these issues for some (or even all) of the sample preparation steps. Here, we detail three optimised step-by-step protocols to: (A) lyse Gram-negative bacteria and fungal cells; (B) quantify the amount of protein extracted; and (C) normalize the amount of protein and set up tryptic digestion. These protocols have been developed to facilitate rapid, low variance sample preparation of hundreds of samples, be easily implemented on widely-available Beckman-Coulter Biomek automated liquid handlers, and allow flexibility for future protocol development. By using this workflow 50 micrograms of peptides for 96 samples can be prepared for tryptic digestion in under an hour. We validate these protocols by analyzing 47 E. coli and R. toruloides samples and show that this modular workflow provides robust, reproducible proteomic samples for high-throughput applications. The expected results from these protocols are 94 peptide samples from Gram-negative bacterial and fungal cells prepared for bottom-up quantitative proteomic analysis without the need for desalting column cleanup and with peptide variance (CVs) below 15%.

Quantum well waveguide intensity modulator at visible wavelengths using CdZnTe/ZnTe quantum wells

1991 ◽  
Vol 59 (15) ◽  
pp. 1867-1869 ◽  
Author(s):  
D. Lee ◽  
J. E. Zucker ◽  
M. D. Divino ◽  
R. F. Austin ◽  
R. D. Feldman ◽  
...  
Keyword(s):  
Quantum Well ◽  
Quantum Wells ◽  
Intensity Modulator ◽  
Visible Wavelengths

Third-Harmonic Generation in Special Parabolic Quantum Wells

2013 ◽  
Vol 760-762 ◽  
pp. 392-396
Author(s):  
You Bin Yu
Keyword(s):  
Quantum Well ◽  
Density Matrix ◽  
Quantum Wells ◽  
Harmonic Generation ◽  
Third Harmonic Generation ◽  
Third Harmonic ◽  
The Third ◽  
Compact Density ◽  
Asymmetric Quantum ◽  
Parabolic Quantum Wells

Third-harmonic generation in a special asymmetric quantum well is investigated. The third-harmonic generation coefficient is carried out by applying compact-density-matrix method. The numerical results are presented for a GaAs/AlGaAs asymmetric quantum well. The very large third-harmonic generation coefficient is obtained in this quantum well. Moreover, the third-harmonic generation coefficient dependents on the quantum well parameters are investigated, respectively.

Sign in / Sign up

Export Citation Format

Share Document