A new compact and miniaturized multiband uniplanar CPW-fed Monopole antenna with T-slot inverted for multiple wireless applications

2017 ◽  
Vol 9 (7) ◽  
pp. 1541-1545 ◽  
Author(s):  
Rachid Dakir ◽  
Jamal Zbitou ◽  
Ahmed Mouhsen ◽  
Abdelwahed Tribak ◽  
Angel Mediavilla Sanchez ◽  
...  
Keyword(s):  
Return Loss ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Configuration Design ◽  
Rectangular Slot ◽  
Wireless Applications ◽  
Compact Size ◽  
Feeding Technique ◽  
Wireless Application ◽  
Antenna Configuration

In this paper, the design of a new compact uniplanar coplanar waveguide-fed antenna for multiband wireless application is presented and investigated. This antenna has a compact size of 25 × 25 mm2 and consists of a three parallel stub optimized added on rectangular slot to the radiator patch and T-shaped which inverted in the ground plane. The final prototype antenna designing resonantes at frequency bands (2.4–2.9 GHz), (3.7–5.2 GHz), and (5.7–6 GHz) with a return loss less than −10 dB. Details of the antenna configuration, design, simulation, and experimental results are presented, investigated, and discussed. The compactness, simple feeding technique, and conception of the uniplanar design make it easy to be integrated within devices of multiples wireless applications.

Arrow Patch-Slot Antenna for 5G Lower Frequency Band Communications

2021 ◽  
Vol 35 (11) ◽  
pp. 1418-1419
Author(s):  
Yuhao Feng ◽  
Yiming Chen ◽  
Atef Elsherbeni ◽  
Khalid Alharbi
Keyword(s):  
Antenna Arrays ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Base Stations ◽  
Slot Antenna ◽  
Main Beam ◽  
Antenna Element ◽  
Single Element ◽  
Rectangular Slot ◽  
Compact Size

A compact size arrow shaped patch in a rectangular slot antenna is designed for 5G communications in the lower 3 to 6 GHz band. The antenna element is fed through a coplanar waveguide with partial ground plane for better impedance matching with 50 Ohms across the entire band. The maximum gain of a single element is 3.8 dB at 3.7 GHz, while for linear arrays of 5 and 15 elements with uniform excitation the maximum gains are 10.9 dB and 16 dB, respectively. The 5 and 15 elements arrays provide scanning range with no significant degradation of the main beam up to 30˚ and 45˚, respectively. The properties of this antenna element makes it suitable for 5G wireless mobile devices and miniaturized base stations antenna arrays.

scholarly journals A Novel Coplanar Waveguide-Fed Compact Microstrip Antenna for Future 5G Applications

2020 ◽  
Vol 14 (2) ◽  
pp. 104-110
Author(s):  
Mustafa Berkan Bicer
Keyword(s):  
Microstrip Antenna ◽  
Return Loss ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Antenna Design ◽  
Method Of Moment ◽  
Full Wave ◽  
Compact Size ◽  
Compact Microstrip Antenna ◽  
Acs Algorithm

In this study, a coplanar waveguide-fed compact microstrip antenna design for applications operating at higher 5G bands was proposed. The antenna with the compact size of 8 x 12.2 mm2 on FR4 substrate, having the dielectric constant of 4.3 and the height of 1.55 mm, was considered. The dimensions of the radiating patch and ground plane were optimized with the use of artificial cooperative search (ACS) algorithm to provide the desired return loss performance of the designed antenna. The performance analysis was done by using full-wave electromagnetic package programs based on the method of moment (MoM) and the finite integration technique (FIT). The 10 dB bandwidth for return loss results obtained with the use of the computation methods show that the proposed antenna performs well for 5G applications operating in the 24.25 – 27.50 GHz, 26.50 – 29.50 GHz, 27.50 – 28.35 GHz and 37 – 40 GHz frequency bands.

scholarly journals Design of Transparent Antenna for 5G Wireless Applications

Proceedings ◽  
2020 ◽  
Vol 63 (1) ◽  
pp. 54
Author(s):  
Sanae Azizi ◽  
Laurent Canale ◽  
Saida Ahyoud ◽  
Georges Zissis ◽  
Adel Asselman
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Light Weight ◽  
Frequency Bandwidth ◽  
Frequency Range ◽  
Wireless Applications ◽  
Compact Size

This paper presents the design of a compact size band patch antenna for 5G wireless communications. This wideband antenna was designed on a glass substrate (12 × 11 × 2 mm3) and is optically transparent and compact. It consists of a radiation patch and a ground plane using AgHT-8 material. The antenna design comprises rectangular shaped branches optimized to attain the wideband characteristics. The calculated impedance bandwidth is 7.7% covering the frequency range of 25 to 27 GHz. A prototype of the antenna and various parameters such as return loss plot, gain plot, radiation pattern plot, and voltage standing wave ratio (VSWR) are presented and discussed. The simulated results of this antenna show that it is well suited for future 5G applications because of its transparency, flexibility, light weight, and wide achievable frequency bandwidth near the millimeter wave frequency band.

Compact Triple/Quadruple-Band Reconfigurable Monopole Antenna for Wireless Applications

2021 ◽  
pp. 2150277
Author(s):  
Asmaa Zugari ◽  
Wael Abd Ellatif Ali ◽  
Mohammad Ahmad Salamin ◽  
El Mokhtar Hamham
Keyword(s):  
Simple Structure ◽  
Low Cost ◽  
Ground Plane ◽  
Monopole Antenna ◽  
Pin Diode ◽  
Wireless Applications ◽  
Rectangular Patch ◽  
Antenna Performance ◽  
Compact Size ◽  
Multi Band

In this paper, a compact reconfigurable tri-band/quad-band monopole antenna is presented. To achieve the multi-band behavior, two right-angled triangles were etched in a conventional rectangular patch, and a partial ground plane is used. Moreover, the proposed multi-band antenna is printed on a low cost FR4 epoxy with compact dimensions of 0.23[Formula: see text], where [Formula: see text] is calculated at the lowest resonance frequency. To provide frequency agility, a metal strip which acts as PIN diode was embedded in the frame of the modified patch. The tri-band/quad-band antenna performance in terms of reflection coefficient, radiation patterns, peak gain and efficiency was studied. The measured results are consistent with the simulated results for both cases. The simple structure and the compact size of the proposed antenna could make it a good candidate for multi-band wireless applications.

scholarly journals A Novel Circular Slotted Microstrip-Fed Patch Antenna with three Triangle Shape Defected Ground Structure for Multiband Applications

2018 ◽  
Vol 7 (3) ◽  
pp. 56-63 ◽  
Author(s):  
A. Jaiswal ◽  
R. K. Sarin ◽  
B. Raj ◽  
S. Sukhija
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Impedance Matching ◽  
Ground Plane ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Resonant Frequencies ◽  
Wireless Applications ◽  
Rectangular Patch ◽  
Miniaturized Antenna

In this paper, a novel circular slotted rectangular patch antenna with three triangle shape Defected Ground Structure (DGS) has been proposed. Radiating patch is made by cutting circular slots of radius 3 mm from the three sides and center of the conventional rectangular patch structure and three triangle shape defects are presented on the ground layer. The size of the proposed antenna is 38 X 25 mm2. Optimization is performed and simulation results have been obtained using Empire XCcel 5.51 software. Thus, a miniaturized antenna is designed which has three impedance bandwidths of 0.957 GHz,  0.779 GHz, 0.665 GHz with resonant frequencies at 3.33 GHz, 6.97 GHz and 8.59 GHz and the corresponding return loss at the three resonant frequencies are -40 dB, -43 dB and -38.71 dB respectively. A prototype is also fabricated and tested. Fine agreement between the measured and simulated results has been obtained. It has been observed that introducing three triangle shape defects on the ground plane results in increased bandwidth, less return loss, good radiation pattern and better impedance matching over the required operating bands which can be used for wireless applications and future 5G applications.

A Low Loss Fully Embedded Stripline Parallel Coupled BPF for Applications using the 60 GHz Band

2011 ◽  
Vol 2011 (CICMT) ◽  
pp. 000050-000053
Author(s):  
Alexander Schulz ◽  
Sven Rentsch ◽  
Lei Xia ◽  
Robert Mueller ◽  
Jens Mueller
Keyword(s):  
Return Loss ◽  
Bandpass Filter ◽  
Coplanar Waveguide ◽  
Center Frequency ◽  
60 Ghz ◽  
Low Loss ◽  
Wireless Applications ◽  
High Data ◽  
V Band ◽  
Waveguide Transmission

This paper presents a low loss fully embedded bandpass filter (BPF) using low temperature co-fired ceramic (LTCC) for multilayer System-in-Package (SiP) and Multi-Chip-Module (MCM) applications, e.g. wireless applications for the unlicensed 60 GHz band. The measured insertion loss was 1.5 dB at the center frequency 58 GHz, and a return loss of less than −10 dB was achieved, including two grounded coplanar waveguide transmission line (CPWg) to stripline transitions. The four layers BPF has a 3 dB bandwidth of about 11 GHz which supplies e.g. broadband and high data rate applications. The whole BPF requires a substrate area of 5.6 × 2.1 × 0.42 mm3 with transitions and a shielding via fence. This BPF suits well for V-band applications in a LTCC package because of the compact dimensions and the good performance.

Dual-Band Proximity Coupled Feed Microstrip Patch Antenna with ‘T’ Slot on the Radiating Patch and ‘Dumbbell’ Shaped Defected Ground Structure

2016 ◽  
Vol 3 (2) ◽  
pp. 435 ◽  
Author(s):  
Dawit Fitsum ◽  
Dilip Mali ◽  
Mohammed Ismail
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Microstrip Patch Antenna ◽  
Dual Band ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Wireless Applications ◽  
Microstrip Patch ◽  
Rectangular Microstrip Patch Antenna

<p>This paper presents Dual-Band proximity coupled feed rectangular Microstrip patch antenna with slots on the radiating patch and Defected Ground Structure. Initially a simple proximity coupled feed rectangular Microstrip patch antenna resonating at 2.4 GHz is designed. Etching out a ‘Dumbbell’ shaped defect from the ground plane and ‘T’ shaped slot from the radiating patch of the proximity coupled feed rectangular Microstrip patch antenna, results in a Dual-Band operation, i.e., resonating at 2.4 GHz and 4.5 GHz; with 30.3 % and 18.8% reduction in the overall area of the patch and the ground plane of the reference antenna respectively. The proposed antenna resonates in S-band at frequency of 2.4 GHz with bandwidth of 123.6 MHz and C-band at frequency of 4.5 GHz with bandwidth of 200 MHz, and a very good return loss of -22.1818 dB and -19.0839 dB at resonant frequency of 2.4 GHz and 4.5 GHz respectively is obtained. The proposed antenna is useful for different wireless applications in the S-band and C-band.</p>

MULTIBAND CPW-FED SLOT ANTENNA FOR WLAN/WIMAX APPLICATIONS

2015 ◽  
Vol 77 (10) ◽  
Author(s):  
Igbafe Orikumhi ◽  
Mohamad Rijal Hamid ◽  
Ali Nyangwarimam Obadiah
Keyword(s):  
Radiation Pattern ◽  
Return Loss ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Slot Antenna ◽  
Frequency Range ◽  
Resonant Frequencies ◽  
Good Agreement

A square slot antenna fed by a coplanar waveguide (CPW) is presented in this paper. The design consist of two pairs of “F” shaped planar strips placed within a square slotted ground. The strips are used to excite multiple resonant frequencies, the strips are connected to the ground plane by means of ideal switches. The proposed antenna has achieved multiple resonant frequencies of 2.4/5.2/5.8 GHz for WLAN and 3.5/5.5 for WiMAX applications. The measured results shows a good agreement with the simulated results in terms of return loss, radiation pattern and gain. The proposed antenna is designed for the frequency range of 2 GHz to 7 GHz which makes it suitable for Bluetooth, WLAN and WiMAX applications. 

A Superwideband Monopole Multiple-Input-Multiple-Output (MIMO) Antenna with Dual Notched (Inverted T-Shaped Stub/U-Shaped Slit) Band Characteristics for Wireless Applications

2019 ◽  
Vol 16 (10) ◽  
pp. 4242-4248
Author(s):  
Manoj Kapil ◽  
Manish Sharma
Keyword(s):  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Impedance Bandwidth ◽  
Mimo Antenna ◽  
Wireless Applications ◽  
Research Article ◽  
Compact Size ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Microstrip Feed

In this research article, a compact MIMO (Multiple-Input-Multiple-Output) antenna with inclusion of two notched bands characteristics is presented. Designed MIMO antenna consist of dual radiating patches printed on one surface of the substrate which covers measured wide impedance bandwidth of 2.88 GHz–19.98 GHz and satisfies bandwidth ratio more than 10:1 for superwideband with compact size of 18 mm × 34 mm. Two radiating patch are placed symmetrically for MIMO configuration and notched bands to eliminate WiMAX/C and WLAN bands are obtained by attaching inverted T-shaped stub on radiating patch and etched inverted U-shape slit in microstrip feed. Isolation between the two radiating patch is maintained by adding two L-shaped stub in slotted rectangular ground plane. Measured radiation pattern are stable in operating band and offers maximum 4.23 dBi and 89% gain and radiation efficiency respectively. Moreover, antenna shows good diversity performance with Envelope-Correlation-Coefficient (ECC) < 0.5, Directive-Gain (DG) > 9.95 dB and Total-Active-Reflection Coefficient (TARC) < -30 dB.

scholarly journals Frequency-Adjustable Small Zeroth-Order Resonant Antenna with Capacitor-Loaded Rectangular Slot on Ground Plane

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Youngsoo Jang ◽  
Sungjoon Lim
Keyword(s):  
Resonant Frequency ◽  
Ground Plane ◽  
Zeroth Order ◽  
Antenna Size ◽  
Rectangular Slot ◽  
Order Resonance ◽  
Frequency Adjustment ◽  
Compact Size ◽  
Small Antenna

A capacitor-loaded electrical small zeroth-order resonant (ZOR) antenna is proposed. The proposed antenna is designed on the basis of a mushroom structure for zeroth-order resonance. To obtain a compact size, the proposed antenna has a rectangular slot on the ground plane, and the chip capacitor is mounted on the slot. The resonant frequency is easily controlled from 2.82 GHz to 2.29 GHz by changing the capacitance from 1 pF to 7 pF, respectively. Therefore, the proposed antenna has the advantages of a small antenna size as well as easy frequency adjustment.

Sign in / Sign up

Export Citation Format

Share Document