scholarly journals The study on the effect of flotation purification on the performance of α-hemihydrate gypsum prepared from phosphogypsum

2022 ◽  
Vol 12 (1) ◽  
Author(s):  
Mingxia Du ◽  
Jinming Wang ◽  
Faqin Dong ◽  
Zhaojia Wang ◽  
Feihua Yang ◽  
...  
Keyword(s):  
Maleic Acid ◽  
Average Length ◽  
Impurity Content ◽  
High Strength ◽  
Industrial Solid Waste ◽  
Aluminium Sulfate ◽  
Before And After ◽  
Flotation Method ◽  
Different Doses ◽  
Better Than

AbstractPhosphogypsum (PG) is a massive industrial solid waste. In this paper, PG was purified by flotation method, and α-hemihydrate gypsum (α-HH) was prepared by the autoclaving method. The morphology of α-HH was adjusted by adding different doses of Maleic acid and Aluminium sulfate. The results showed that after flotation purification, the impurity content in PG was significantly reduced, the soluble phosphorus content decreased from 0.48 to 0.07%, the PG purity increased from 73.12 to 94.37%, and the PG whiteness risen from 19.4 to 40.5. Then the performance of α-HH prepared from PG before and after purification was compared. Fixing the amount of aluminium sulfate at 0.2 wt%, the reaction temperature at 140 °C, and the reaction time at 120 min, the average length/diameter ratio of α-HH crystals decreased from 7.2 to 0.6 as the amount of Maleic acid increased from 0 to 0.17 wt%. When the amount of Maleic acid was 0.13 wt%, the α-hemihydrate gypsum reached the best mechanical properties. The mechanical strength of high strength gypsum prepared from PG concentrate was significantly better than that of raw PG, indicating that flotation purification can effectively improve the performance of PG. In this study, a new method of PG purification and resource utilization was proposed.

scholarly journals Comparative Study of α-Hemihydrate Preparation from Phosphogypsum Before and After Flotation Purification

2021 ◽  
Author(s):  
Mingxia Du ◽  
Jinming Wang ◽  
Faqin Dong ◽  
Zhaojia Wang ◽  
Feihua Yang ◽  
...  
Keyword(s):  
Maleic Acid ◽  
Average Length ◽  
Impurity Content ◽  
High Strength ◽  
Industrial Solid Waste ◽  
Aluminium Sulfate ◽  
Before And After ◽  
Flotation Method ◽  
Different Doses ◽  
Better Than

Abstract Phosphogypsum (PG) is a massive industrial solid waste. In this paper, PG was purified by flotation method, and α-hemihydrate gypsum (α-HH) was prepared by the autoclaving method. The morphology of α-HH was adjusted by adding different doses of Maleic acid and Aluminium sulfate. The results showed that after flotation purification, the impurity content in PG was significantly reduced, the soluble phosphorus content decreased from 0.48% to 0.07%, the PG purity increased from 73.12% to 94.37%, and the PG whiteness risen from 19.4 to 40.5. Then the performance of α-HH prepared from PG before and after purification was compared. Fixing the amount of Aluminium sulfate at 0.2wt%, the reaction temperature at 140°C, and the reaction time at 120min, the average length/diameter ratio of α-HH crystals decreased from 7.2 to 0.6 as the amount of Maleic acid increased from 0 to 0.17wt%. When the amount of Maleic acid was 0.13wt%, the α-hemihydrate gypsum reached the best mechanical properties. The mechanical strength of high strength gypsum prepared from PG concentrate was significantly better than that of raw PG, indicating that flotation purification can effectively improve the performance of PG. In this study, a new method of PG purification and resource utilization was proposed.

The Study of Anti-UV and Anti-Solarization of Strength Synthetic Fiber

2012 ◽  
Vol 573-574 ◽  
pp. 1224-1229
Author(s):  
Hai Yan Ni ◽  
Ying Jin Gan ◽  
Jin Ti You
Keyword(s):  
Fiber Bundle ◽  
Performance Test ◽  
High Strength ◽  
Uv Protection ◽  
National Standards ◽  
Synthetic Fiber ◽  
Test Results ◽  
Before And After ◽  
The Difference ◽  
Better Than

In view of anti-UV of the high strength synthetic fiber hoisting belt, the researcher compared the effects on anti-ultraviolet of SCJ-966 and HTUV100,through before and after intensity test and the test of Anti-solarization performance,then comparing with tests of fiber bundle strength,the reacher analyzed the effect of anti-UV and the difference on intensity.The result shows that:two UV performance are very good, far more than the European and national standards,and the webbing performance test results show that the UV protection of SCJ-966 UV protection is better than HTUV100, but the intensity rate is the former smaller than the latter, the extent damage of hoisting belt is the latter worse than the former.

Kepuasan Masyarakat Terhadap Pelayanan Kelurahan Setelah Pemekaran Di Tangerang Selatan

Liquidity ◽  
2018 ◽  
Vol 2 (2) ◽  
pp. 151-159
Author(s):  
Pitri Yandri
Keyword(s):  
Public Perception ◽  
Service Personnel ◽  
Urban Services ◽  
Hospitality Workers ◽  
Care Workers ◽  
Before And After ◽  
Cartesian Diagram ◽  
Better Than

The purpose of this study is (1) to analyze public perception on urban services before and after the expansion of the region, (2) analyze the level of people's satisfaction with urban services, and (3) analyze the determinants of the variables that determine what level of people's satisfaction urban services. This study concluded that first, after the expansion, the quality of urban services in South Tangerang City is better than before. Secondly, however, public satisfaction with the services only reached 48.53% (poor scale). Third, by using a Cartesian Diagram, the second priority that must be addressed are: (1) clarity of service personnel, (2) the discipline of service personnel, (3) responsibility for care workers; (4) the speed of service, (5) the ability of officers services, (6) obtain justice services, and (7) the courtesy and hospitality workers.

In vitro Behaviour of Alumina-Hydroxiapatite Composites Coatings

2018 ◽  
Vol 69 (6) ◽  
pp. 1416-1418
Author(s):  
Alexandru Szabo ◽  
Ilare Bordeasu ◽  
Ion Dragos Utu ◽  
Ion Mitelea
Keyword(s):  
Pure Titanium ◽  
Titanium Substrate ◽  
High Strength ◽  
Biological Properties ◽  
Commercially Pure Titanium ◽  
Hvof Spraying ◽  
Before And After ◽  
Sbf Solution ◽  
Oxygen Fuel

Hydroxyapatite (HA) is a very common material used for biomedical applications. Usually, in order to improve its poor mechanical properties is combined or coated with other high-strength materials.The present paper reports the manufacturing and the biocompatibility behaviour of two different biocomposite coatings consisting of alumina (Al2O3) and hydroxyapatite (HA) using the high velocity oxygen fuel (HVOF) spraying method which were deposited onto the surface of a commercially pure titanium substrate. The biological properties of the Al2O3-HA materials were evaluated by in vitro studies. The morphology of the coatings before and after their immersing in the simulated body fluid (SBF) solution was characterized by scanning electron microscopy (SEM). The results showed an important germination of the biologic hydroxyapatite crystallite on the surface of both coatings.

scholarly journals Network robustness improvement via long-range links

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Vincenza Carchiolo ◽  
Marco Grassia ◽  
Alessandro Longheu ◽  
Michele Malgeri ◽  
Giuseppe Mangioni
Keyword(s):  
Complex Networks ◽  
Long Range ◽  
Real World ◽  
Network Robustness ◽  
Scale Free ◽  
Area Of Interest ◽  
Before And After ◽  
Significant Area ◽  
Better Than

AbstractMany systems are today modelled as complex networks, since this representation has been proven being an effective approach for understanding and controlling many real-world phenomena. A significant area of interest and research is that of networks robustness, which aims to explore to what extent a network keeps working when failures occur in its structure and how disruptions can be avoided. In this paper, we introduce the idea of exploiting long-range links to improve the robustness of Scale-Free (SF) networks. Several experiments are carried out by attacking the networks before and after the addition of links between the farthest nodes, and the results show that this approach effectively improves the SF network correct functionalities better than other commonly used strategies.

scholarly journals Six ultraviolet minutes for cleaner operating theatres

2020 ◽  
Vol 30 (Supplement_5) ◽  
Author(s):  
R Bosco ◽  
S Gambelli ◽  
V Urbano ◽  
G Cevenini ◽  
G Messina
Keyword(s):  
Cross Sectional Study ◽  
Cross Sectional ◽  
Before And After ◽  
Operating Theatres ◽  
Cleaning Procedures ◽  
The Difference ◽  
Contamination Levels ◽  
Different Levels ◽  
Better Than ◽  
Final Cleaning

Abstract Background Sanitizing the operating theatres (OT) is important to minimize risk of post-operative infections. Disinfection procedures between one operation and another is less aggressive than final cleaning procedures, at the end of the day. Aim was assessing the difference of contamination: i) between different levels of disinfection; ii) before and after the use of a UVC Device (UVC-D). Methods Between December 2019/February 2020 a cross sectional study was conducted in OT in a real clinical context. 94 Petri dishes (PD) were used in 3 OT. Three different sanitation levels (SL1-3) were compared pre- and post-use of UVC-D: i) No cleaning after surgery (SL1); ii) after in-between cleaning (SL2); iii) after terminal cleaning (SL3). UVC-D was employed for 6 minutes, 3 minutes per bed side. PD were incubated at 36 °C and colony forming unit (CFU) counted at 48h. Descriptive statistic, Wilcoxon and Mann-Whitney tests were performed to assess the contamination levels in total, pre/post use of UVC-D, and between different sanitation levels, respectively. Results In total we had a mean of 3.39 CFU/PD (C.I. 2.05 - 4.74) and a median of 1 CFU/PD (Min. 0 - Max. 39), after UVC-D use we had a mean of 2.20 CFU/PD (C.I. 0.69 - 5.09) and a median of 0 CFU/PD (Min. 0 - Max. 133). The UVC-D led to a significant reduction of CFU (p < 0.001). Without UVC-D we had a significant CFU drop (p < 0.05) between SL1 and SL3. Using UVC-D, we observed significant reductions of contamination (p < 0.05) between SL3 and SL1. Comparing SL1 (median 0) post UVC-D use vs SL2 pre UVC-D use (median 0.5), and SL2 post UVC-D use (median 0) vs SL3 pre UVC-D use (median 1) we had a significant reduction of contamination (p < 0.05). Conclusions UVC-D improved environmental contamination in any of the three sanitation levels. Furthermore, the use of UVC-D alone was better than in-between and terminal cleaning. Although these encouraging results, the cleaning procedures executed by dedicated staff has to be considered. Key messages UVC are efficient to decrease contamination in operating theatres regardless of sanitation levels. The additional use of UVC technology to standard cleaning procedures significantly improves sanitation levels.

scholarly journals Sustainable and Clean Utilization of Yellow Phosphorus Slag (YPS): Activation and Preparation of Granular Rice Fertilizer

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2080
Author(s):  
Cuihong Hou ◽  
Luyi Li ◽  
Lishuang Hou ◽  
Bingbing Liu ◽  
Shouyu Gu ◽  
...  
Keyword(s):  
Particle Size ◽  
High Strength ◽  
Water Quenching ◽  
Smelting Process ◽  
Industrial Solid Waste ◽  
Rice Roots ◽  
Yellow Phosphorus ◽  
Quenching Process ◽  
Reduction Smelting ◽  
Nitrogen Phosphorus

Yellow phosphorus slag (YPS) is a typical industrial solid waste, while it contains abundant silicon micronutrient required for the growth of rice. The key scientific problem to use the YPS as rice fertilizer is how to activate the slag efficiently during the phosphorite reduction smelting process. In this work, an alkaline rice fertilizer from the activated YPS was successfully prepared to use the micronutrients. Thermodynamic analyses of SiO2-CaO, SiO2-CaO-Al2O3, and SiO2-CaO-Al2O3-MgO systems were discussed to optimize the acidity for reduction smelting. Results showed that the reduction smelting followed by the water quenching process can realize the reduction of phosphorite and activation of YPS synchronously. Ternary acidity m(SiO2)/(m(CaO) + m(MgO)) of 0.92 is suitable for the reduction smelting and activation of the slag. After smelting, the molten YPS can be effectively activated by water quenching, and 78.28% P, 90.03% Ca, and 77.12% Si in the YPS are activated, which can be readily absorbed by the rice roots. Finally, high-strength granular rice fertilizers with a particle size of Φ2–4 mm were successfully prepared from the powdery nitrogen-phosphorus-potassium (NPK) and activated YPS mixture.

scholarly journals More skilled clinical management of COVID-19 patients modified mortality in an intermediate respiratory intensive care unit in Italy

2021 ◽  
Vol 22 (1) ◽  
Author(s):  
Giovanna E. Carpagnano ◽  
Giovanni Migliore ◽  
Salvatore Grasso ◽  
Vito Procacci ◽  
Emanuela Resta ◽  
...  
Keyword(s):  
Intensive Care Unit ◽  
Intensive Care ◽  
Severe Acute Respiratory Syndrome ◽  
Clinical Management ◽  
Average Length ◽  
Limited Attention ◽  
Average Length Of Stay ◽  
Before And After ◽  
Respiratory Intensive Care Unit ◽  
Transferred Patients

Abstract Background Some studies investigated epidemiological and clinical features of laboratory-confirmed patients with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) the virus causing coronavirus disease 2019 (COVID-19), but limited attention has been paid to the follow-up of hospitalized patients on the basis of clinical setting and the expertise of clinical management. Methods In the present single-centered, retrospective, observational study, we reported findings from 87 consecutive laboratory-confirmed COVID-19 patients with moderate-to-severe acute respiratory syndrome hospitalized in an intermediate Respiratory Intensive Care Unit (RICU), subdividing the patients in two groups according to the admission date (before and after March 29, 2020). Results With improved skills in the clinical management of COVID-19, we observed a significant lower mortality in the T2 group compared with the T1 group and a significantly difference in terms of mortality among the patients transferred in Intensive Care Unit (ICU) from our intermediate RICU (100% in T1 group vs. 33.3% in T2 group). The average length of stay in intermediate RICU of ICU-transferred patients who survived in T1 and T2 was significantly longer than those who died (who died 3.3 ± 2.8 days vs. who survived 6.4 ± 3.3 days). T Conclusions The present findings suggested that an intermediate level of hospital care may have the potential to modify survival in COVID-19 patients, particularly in the present phase of a more skilled clinical management of the pandemic.

scholarly journals Eco-Friendly Fired Brick Produced from Industrial Ash and Natural Clay: A Study of Waste Reuse

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 877 ◽  
Author(s):  
Neslihan Doğan-Sağlamtimur ◽  
Ahmet Bilgil ◽  
Magdalena Szechyńska-Hebda ◽  
Sławomir Parzych ◽  
Marek Hebda
Keyword(s):  
Compressive Strength ◽  
Bottom Ash ◽  
Unit Weight ◽  
Waste Reuse ◽  
Industrial Solid Waste ◽  
Second Stage ◽  
Before And After ◽  
Fired Bricks ◽  
Two Stages ◽  
And Storage

Bottom ash (BA) is an industrial solid waste formed by the burning of coal. The environmental problems and storage costs caused by this waste increase with every passing day. In this study, the use of BA as an additive (clay substitute) in fired brick production was investigated. The study consisted of two stages. In the first stage, cylinder blocks were produced from clay used in brick production. The second stage was the examination of the experimental substitution of clay with 10, 20, 30 and 40% BA. Samples were fired at 900, 1000, 1100 and 1150 °C to produce fired brick samples. The unit weight, compressive strength (before and after freeze–thawing) and water absorption were analyzed for the samples. The unit weight values decreased in the samples containing BA. The mechanical properties met the conditions prescribed in the relevant standards; i.e., all of the samples fired at 1100 and 1150 °C had a sufficient compressive strength over 20 MPa. The high potential of fired bricks for the construction industry was proved. BA can be used as a clay substitute, while the developed protocol can be used to effectively produce fired bricks.

Microperfusion study of proximal tubule bicarbonate transport in maleic acid-induced renal tubular acidosis

1986 ◽  
Vol 250 (3) ◽  
pp. F476-F482
Author(s):  
N. Bank ◽  
H. S. Aynedjian ◽  
B. F. Mutz
Keyword(s):  
Proximal Tubule ◽  
Renal Tubular Acidosis ◽  
Maleic Acid ◽  
Basolateral Membrane ◽  
Bicarbonate Transport ◽  
Mitochondrial Energy Metabolism ◽  
Before And After ◽  
Renal Tubular ◽  
Blood Transport ◽  
Acid Administration

Microperfusion studies were carried out in rats to examine the abnormality in proximal tubule HCO3- transport caused by maleic acid administration. Permeability of the proximal tubule to HCO-3 was measured by perfusing proximal tubules with a HCO3- -free low-buffer isotonic equilibrium solution containing acetazolamide after plasma [HCO3-] had been raised by intravenous NaHCO3 infusion. Insulin recovery in the collected perfusate was approximately 100% in control and maleic acid-treated rats. CO2 influx measured by microcalorimetry was not significantly different in control vs. maleic acid-treated rats. Thus maleic acid did not cause increased permeability of the proximal tubule to either inulin or HCO3-. In a second group of experiments, proximal tubule fluid and HCO3- efflux were measured in paired-reperfusion experiments before and after maleic acid administration. The perfusion fluid contained 25 mM HCO3- and 120 mM Cl-. HCO3- absorption was inhibited 25% (79 pmol/min), Na+ was inhibited 22% (164 pmol/min), and Cl- absorption (calculated as the anion gap) by 85 pmol/min. [HCO3-] in the collected perfusate rose significantly after maleic acid, presumably accompanied by a fall in [Cl-]. The observations indicate that proximal renal tubular acidosis (RTA) induced by maleic acid is characterized by impaired lumen-to-blood transport of sodium bicarbonate and chloride but not by increased backflux. Based on previously demonstrated effects of maleic acid on mitochondrial energy metabolism and cellular ATP levels, we postulate that the principal transport abnormality is impaired basolateral membrane active sodium transport, leading to a secondary reduction in brush border Na+-H+ exchange.(ABSTRACT TRUNCATED AT 250 WORDS)

Sign in / Sign up

Export Citation Format

Share Document