Graphene dispersion in hydrocarbon medium and its application in lubricant technology

RSC Advances ◽  
2015 ◽  
Vol 5 (66) ◽  
pp. 53326-53332 ◽  
Author(s):  
Jyotiranjan Ota ◽  
S. K. Hait ◽  
M. I. S. Sastry ◽  
S. S. V. Ramakumar
Keyword(s):  
Thermal Conductivity ◽  
Coefficient Of Friction ◽  
Heat Dissipation ◽  
Lubricating Oils ◽  
Stable Dispersion ◽  
Hydrocarbon Medium ◽  
Graphene Dispersion ◽  
The Coefficient Of Friction

The stable dispersion of graphene in formulated lubricating oils reduces the coefficient of friction and significantly improves heat dissipation from the system owing to its higher thermal conductivity.

scholarly journals Development of Standardized Material Testing Protocols for Prosthetic Liners

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
John C. Cagle ◽  
Per G. Reinhall ◽  
Brian J. Hafner ◽  
Joan E. Sanders
Keyword(s):  
Thermal Conductivity ◽  
Coefficient Of Friction ◽  
Test Chamber ◽  
Clinical Environment ◽  
Test Procedures ◽  
Element Analysis ◽  
Diverse Range ◽  
Wide Range ◽  
Shear Elasticity ◽  
The Coefficient Of Friction

A set of protocols was created to characterize prosthetic liners across six clinically relevant material properties. Properties included compressive elasticity, shear elasticity, tensile elasticity, volumetric elasticity, coefficient of friction (CoF), and thermal conductivity. Eighteen prosthetic liners representing the diverse range of commercial products were evaluated to create test procedures that maximized repeatability, minimized error, and provided clinically meaningful results. Shear and tensile elasticity test designs were augmented with finite element analysis (FEA) to optimize specimen geometries. Results showed that because of the wide range of available liner products, the compressive elasticity and tensile elasticity tests required two test maxima; samples were tested until they met either a strain-based or a stress-based maximum, whichever was reached first. The shear and tensile elasticity tests required that no cyclic conditioning be conducted because of limited endurance of the mounting adhesive with some liner materials. The coefficient of friction test was based on dynamic coefficient of friction, as it proved to be a more reliable measurement than static coefficient of friction. The volumetric elasticity test required that air be released beneath samples in the test chamber before testing. The thermal conductivity test best reflected the clinical environment when thermal grease was omitted and when liner samples were placed under pressure consistent with load bearing conditions. The developed procedures provide a standardized approach for evaluating liner products in the prosthetics industry. Test results can be used to improve clinical selection of liners for individual patients and guide development of new liner products.

Stability of Frictional Sliding With the Coefficient of Friction Depended on the Temperature

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Vahid Mortazavi ◽  
Chuanfeng Wang ◽  
Michael Nosonovsky
Keyword(s):  
Thermal Conductivity ◽  
Temperature Field ◽  
Coefficient Of Friction ◽  
Temperature Dependency ◽  
Brake Disk ◽  
Frictional Sliding ◽  
Disk Brake ◽  
The Coefficient Of Friction ◽  
Surface Temperature Field

Friction-induced instabilities can be caused by different separate mechanisms such as elastodynamic or thermoelastic. This paper suggests another type of instability due to the temperature dependency of the coefficient of friction. The perturbations imposed on the surface temperature field during the frictional sliding can grow or decay. A stability criterion is formulated and a case study of a brake disk is performed with a simple model without including effects of transforming layer and chemical/physical properties change with temperature. The disk is rigid and the coefficient of friction depends on temperature. We show that the mechanism of instability can contribute to poor reproducibility of aircraft disk brake tests reported in the literature. We propose a method to increase the reproducibility by dividing the disk into several sectors with decreased thermal conductivity between the sectors.

Synthesis of nanostructured flower-like MoS2 and its friction properties as additive in lubricating oils

2016 ◽  
Vol 68 (6) ◽  
pp. 658-664 ◽  
Author(s):  
Gustavo Tontini ◽  
Guilherme Dalla Lana Semione ◽  
Cristian Bernardi ◽  
Roberto Binder ◽  
José Daniel Biasoli de Mello ◽  
...  
Keyword(s):  
Hydrothermal Method ◽  
Coefficient Of Friction ◽  
Absolute Ethanol ◽  
Molybdenum Disulphide ◽  
Content Type ◽  
Lubricating Oils ◽  
The Coefficient Of Friction ◽  
Powder Particles ◽  
The Stability ◽  
Pin On Disk

Purpose This paper aims to synthesize nanostructured flower-like molybdenum disulphide (MoS2) particles and evaluate their suitability to act as additives for lubricants. Design/methodology/approach A hydrothermal method without any surfactant successfully produced 250 nm mean diameter Nanostructured flower-like MoS2 particles. The resulting product was then solvothermally treated with absolute ethanol producing lipophilic powder particles which after being dispersed in two different lubricants were tribologicaly characterized by using a pin-on-disk tribometer geometry with reciprocal movement under immersion. Findings The influence on the stability and the coefficient of friction of the nano-oils is shown to be strongly dependent on their molecular structure. After 1 h of tribological testing, a ramified polyolester oil with 1 Wt.% of MoS2 nanoflowers did not show decrease in its average coefficient of friction, while an additive naphthenic oil with the same concentration of nanoparticles showed a decrease of 86 per cent. Originality/value In this paper, nanostructured flower-like MoS2 synthesized by the hydrothermal method was dispersed in lubricating oils to study its stability and tribological properties. To ensure good stability of the nano-oils, the particles were solvothermally treated with absolute ethanol to dehydrate and lipophilize them. A ramified polyolester-based nano-oil with 1 Wt.% of MoS2 nanoflowers showed no decrease in its steady state coefficient of friction, while a naphthenic-based nano-oil with the same concentration of nanoparticles presented a remarkable 86 per cent reduction.

Experimental Investigation of aluminum doping crumb rubber/epoxy composite in reciprocating motion

2015 ◽  
Vol 3 ◽  
pp. 1
Author(s):  
Goutam Chandra Karar ◽  
Nipu Modak
Keyword(s):  
Experimental Investigation ◽  
Coefficient Of Friction ◽  
Epoxy Composite ◽  
Normal Load ◽  
Crumb Rubber ◽  
The Other ◽  
Reciprocating Motion ◽  
Molding Process ◽  
Friction Tester ◽  
The Coefficient Of Friction

The experimental investigation of reciprocating motion between the aluminum doped crumb rubber /epoxy composite and the steel ball has been carried out under Reciprocating Friction Tester, TR-282 to study the wear and coefficient of frictions using different normal loads (0.4Kg, 0.7Kgand1Kg), differentfrequencies (10Hz, 25Hz and 40Hz).The wear is a function of normal load, reciprocating frequency, reciprocating duration and the composition of the material. The percentage of aluminum presents in the composite changesbut the other components remain the same.The four types of composites are fabricated by compression molding process having 0%, 10%, 20% and 30% Al. The effect of different parameters such as normal load, reciprocating frequency and percentage of aluminum has been studied. It is observed that the wear and coefficient of friction is influenced by the parameters. The tendency of wear goes on decreasing with the increase of normal load and it is minimum for a composite having 10%aluminum at a normal load of 0.7Kg and then goes on increasing at higher loads for all types of composite due to the adhesive nature of the composite. The coefficient of friction goes on decreasing with increasing normal loads due to the formation of thin film as an effect of heat generation with normal load.

scholarly journals Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4217
Author(s):  
Üsame Ali Usca ◽  
Mahir Uzun ◽  
Mustafa Kuntoğlu ◽  
Serhat Şap ◽  
Khaled Giasin ◽  
...  
Keyword(s):  
Weight Loss ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Applied Load ◽  
Practical Significance ◽  
Tribological Characteristics ◽  
M 10 ◽  
Wide Range ◽  
The Coefficient Of Friction ◽  
Four Levels

Tribological properties of engineering components are a key issue due to their effect on the operational performance factors such as wear, surface characteristics, service life and in situ behavior. Thus, for better component quality, process parameters have major importance, especially for metal matrix composites (MMCs), which are a special class of materials used in a wide range of engineering applications including but not limited to structural, automotive and aeronautics. This paper deals with the tribological behavior of Cu-B-CrC composites (Cu-main matrix, B-CrC-reinforcement by 0, 2.5, 5 and 7.5 wt.%). The tribological characteristics investigated in this study are the coefficient of friction, wear rate and weight loss. For this purpose, four levels of sliding distance (1000, 1500, 2000 and 2500 m) and four levels of applied load (10, 15, 20 and 25 N) were used. In addition, two levels of sliding velocity (1 and 1.5 m/s), two levels of sintering time (1 and 2 h) and two sintering temperatures (1000 and 1050 °C) were used. Taguchi’s L16 orthogonal array was used to statistically analyze the aforementioned input parameters and to determine their best levels which give the desired values for the analyzed tribological characteristics. The results were analyzed by statistical analysis, optimization and 3D surface plots. Accordingly, it was determined that the most effective factor for wear rate, weight loss and friction coefficients is the contribution rate. According to signal-to-noise ratios, optimum solutions can be sorted as: the highest levels of parameters except for applied load and reinforcement ratio (2500 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 0 wt.%) for wear rate, certain levels of all parameters (1000 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 2.5 wt.%) for weight loss and 1000 m, 15 N, 1 m/s, 1 h, 1000 °C and 0 wt.% for the coefficient of friction. The comprehensive analysis of findings has practical significance and provides valuable information for a composite material from the production phase to the actual working conditions.

scholarly journals Influence of Beam Power on Young’s Modulus and Friction Coefficient of Ti–Ta Alloys Formed by Electron-Beam Surface Alloying

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1246
Author(s):  
Stefan Valkov ◽  
Dimitar Dechev ◽  
Nikolay Ivanov ◽  
Ruslan Bezdushnyi ◽  
Maria Ormanova ◽  
...  
Keyword(s):  
Electron Beam ◽  
Young’S Modulus ◽  
Coefficient Of Friction ◽  
Young's Modulus ◽  
Beam Power ◽  
Surface Alloying ◽  
Surface Alloys ◽  
X Ray ◽  
The Coefficient Of Friction ◽  
Beam Surface

In this study, we present the results of Young’s modulus and coefficient of friction (COF) of Ti–Ta surface alloys formed by electron-beam surface alloying by a scanning electron beam. Ta films were deposited on the top of Ti substrates, and the specimens were then electron-beam surface alloyed, where the beam power was varied from 750 to 1750 W. The structure of the samples was characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). Young’s modulus was studied by a nanoindentation test. The coefficient of friction was studied by a micromechanical wear experiment. It was found that at 750 W, the Ta film remained undissolved on the top of the Ti, and no alloyed zone was observed. By an increase in the beam power to 1250 and 1750 W, a distinguished alloyed zone is formed, where it is much thicker in the case of 1750 W. The structure of the obtained surface alloys is in the form of double-phase α’and β. In both surface alloys formed by a beam power of 1250 and 1750 W, respectively, Young’s modulus decreases about two times due to different reasons: in the case of alloying by 1250 W, the observed drop is attributed to the larger amount of the β phase, while at 1750 W is it due to the weaker binding forces between the atoms. The results obtained for the COF show that the formation of the Ti–Ta surface alloy on the top of Ti substrate leads to a decrease in the coefficient of friction, where the effect is more pronounced in the case of the formation of Ti–Ta surface alloys by a beam power of 1250 W.

Reducing the Coefficient of Friction for Fast-Absorbing Gut Suture

2009 ◽  
Vol 35 (12) ◽  
pp. 2004 ◽  
Author(s):  
Jonathan Lee Bingham ◽  
Mariah R. Brown ◽  
Julian Ramsey Mellette
Keyword(s):  
Coefficient Of Friction ◽  
The Coefficient Of Friction

First Paper: Effect of Under-Lip Temperature on the Lubrication of Rotary Shaft Garter Spring Seals

1966 ◽  
Vol 181 (1) ◽  
pp. 185-190 ◽  
Author(s):  
D. J. Lines ◽  
J. M. Lawrie ◽  
J. P. O'Donoghue
Keyword(s):  
Coefficient Of Friction ◽  
Operating Temperature ◽  
Lubrication Theory ◽  
Fluid Film ◽  
Hydrodynamic Parameter ◽  
Accurate Knowledge ◽  
The Coefficient Of Friction ◽  
Surface Thermocouple ◽  
Sealing Mechanism ◽  
Film Lubrication

Although rotary shaft garter spring seals are widely used throughout industry, very little is known about the sealing mechanism of the lip-shaft interface. It is now generally accepted that some sort of fluid film separates the lip and the shaft. Previous workers have also postulated a relationship between the coefficient of friction and a non-dimensional hydrodynamic parameter, as in standard lubrication theory. This present paper clarifies this relationship, and shows that seals can also operate over the mixed friction, as well as the full film lubrication region. The results were obtained by accurate knowledge of the operating temperature under the sealing lip. Two types of surface thermocouple were developed to do this and these are described in full.

The Effect of Nanoparticle Functionalization on Lubrication Performance of Nanofluids Dispersing Silica Nanoparticles in an Ionic Liquid

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Cengiz Yegin ◽  
Wei Lu ◽  
Bassem Kheireddin ◽  
Ming Zhang ◽  
Peng Li ◽  
...  
Keyword(s):  
Silica Nanoparticles ◽  
Coefficient Of Friction ◽  
Shear Thinning ◽  
Antiwear Additives ◽  
Functionalized Silica ◽  
Low Concentrations ◽  
Lubrication Performance ◽  
The Coefficient Of Friction ◽  
High Concentrations ◽  
Newtonian Behavior

Recently, ionic liquids (ILs) have received an increasing attention as lubricants owing to their intriguing properties such as tunable viscosity, high thermal stability, low emissions, nonflammability, and corrosion resistance. In this work, we investigate how the incorporation of octadecyltrichlorosilane (OTS) functionalized silica nanoparticles (NPs) in 1-butyl-3-methylimidazolium (trifluoromethysulfony)imide influences the tribological properties and rheological properties of IL under boundary lubrication and elastohydrodynamic conditions, respectively. It was found that the coefficient of friction was depended on the concentration of NPs in IL with a concave upward functional trend with a minimum at 0.05 wt.% for bare silica NPs and at 0.10 wt.% for OTS-functionalized silica NPs. For steel–steel sliding contact, the presence of functionalized NPs in IL at the optimum concentration decreased the coefficient of friction by 37% compared to IL and 17% compared to IL with bare silica NPs. While IL with bare NPs demonstrated a shear thinning behavior for all concentrations, IL with functionalized NPs showed a Newtonian behavior at low concentrations and shear thinning behavior at high concentrations. Overall, this study provides new insights into the antifriction and antiwear additives for lubrication systems involving ILs.

Sign in / Sign up

Export Citation Format

Share Document