scholarly journals Experimental study on bond performance between GFRP bars and concrete

2020 ◽  
Vol 165 ◽  
pp. 04041
Author(s):  
Fu Decheng ◽  
Wang Bo
Keyword(s):  
Experimental Study ◽  
Bond Strength ◽  
Bond Length ◽  
Concrete Strength ◽  
Bond Failure ◽  
Bond Performance ◽  
Gfrp Bars ◽  
Bonding Performance ◽  
Pull Out ◽  
Gfrp Reinforcement

Based on 27 bonding test of pull-out specimens, the bonding performance between GFRP and concrete was studied systematically. The bond failure between concrete and GFRP includes four stages: microslip stage, linear slip stage, nonlinear slip stage and bond failure stage. The experiment shows that there is no significant correlation between concrete strength and bond strength, bond strength increases with the bond length and decreases with the increase of GFRP reinforcement diameter.

Influence of Test Configuration on Bond Strength of GFRP Bars

2019 ◽  
Vol 292 ◽  
pp. 217-223 ◽  
Author(s):  
Ondřej Janus ◽  
Frantisek Girgle ◽  
Vojtech Kostiha ◽  
Petr Štěpánek ◽  
Pavel Sulak
Keyword(s):  
Bond Strength ◽  
Concrete Cover ◽  
Silica Sand ◽  
Beam Test ◽  
Bond Behaviour ◽  
Test Configuration ◽  
Gfrp Bars ◽  
Pull Out ◽  
Frp Reinforcement ◽  
Gfrp Reinforcement

It is well-known that test configuration affects bond behaviour of steel reinforcement, but this effect has not yet been sufficiently quantified when using FRP reinforcement. This paper presents partial results from an ongoing experimental programme that deals with the bond strength of GFRP bars with concrete, with regards to the effect of the surface treatment of the rebars and test configuration. A modified beam test is presented in this study along with a pull-out test with an eccentric bar placement. The bond strength of GFRP reinforcement with sand-coated treatment using silica sand and ribbed type with milled ribs was tested. The sand-coated bars exhibit different bond behaviour compared to the ribbed ones due to different forces transfer from the reinforcement to the concrete. Thickness of the concrete cover layer also has a significant effect on the bond behaviour of the reinforcement.

scholarly journals Experimental Study on Bond Performance of Carbon- and Glass-Fiber Reinforced Polymer (CFRP/GFRP) Bars and Steel Strands to Concrete

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1268
Author(s):  
Jun Zhao ◽  
Xin Luo ◽  
Zike Wang ◽  
Shuaikai Feng ◽  
Xinglong Gong ◽  
...  
Keyword(s):  
Bond Strength ◽  
Bond Length ◽  
Retention Rate ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Bond Performance ◽  
Gfrp Bars ◽  
Reinforced Polymer ◽  
Gfrp Bar ◽  
Strength Retention

FRP bars and steel strands are widely used in civil engineering. In this study, three different types of high-strength reinforcement materials, carbon fiber reinforced polymer (CFRP) bar, glass fiber reinforced polymer (GFRP) bar, and steel strand, were investigated for their interfacial bond performance with concrete. A total of 90 sets of specimens were conducted to analyze the effects of various parameters such as the diameter of reinforcement, bond length, the grade of concrete and stirrup on the bond strength and residual bond strength. The results show that CFRP bars possess a higher bond strength retention rate than steel bars in the residual section. In addition, with the increase in bond length and diameter of the CFRP bar, the residual bond strength decreases, and the bond strength retention rate decreases. Furthermore, the bond strength retention rate of GFRP bars was found to be higher than that of CFRP bars. With the increase in grade of concrete, the bond strength and residual bond strength between GFRP bars and concrete increases, but the bond strength retention rate decreases. With an increase in bond length and diameter of the GFRP bar, the bond strength starts to decrease. Further, stirrup can also increase the bond strength and reduce the slip at the free end of GFRP bars. Moreover, the bond strength retention rate of the steel strand was found to be lower than CFRP and GFRP bar.

scholarly journals Research on bond–slip performance between pultruded glass fiber-reinforced polymer tube and nano-CaCO3 concrete

2020 ◽  
Vol 9 (1) ◽  
pp. 637-649 ◽  
Author(s):  
Zhan Guo ◽  
Qingxia Zhu ◽  
Wenda Wu ◽  
Yu Chen
Keyword(s):  
Bond Strength ◽  
Concrete Strength ◽  
Fiber Reinforced Polymer ◽  
Glass Fiber Reinforced Polymer ◽  
Bond Slip ◽  
Ordinary Concrete ◽  
Bond Performance ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Push Out

AbstractThe article describes an experimental study on the bond–slip performance between the pultruded glass fiber-reinforced polymer (GFRP) tube and the nano-CaCO3 concrete. Taking the nano-CaCO3 concrete strength and GFRP tube thickness as primary parameters, nine specimens were designed and tested to study the influence of these parameters on the bond strength of the specimens. Besides, three specimens filled with the ordinary concrete were also tested by using the push-out tests to make comparisons with the bond performance of the specimens filled with nano-CaCO3 concrete. A total of four push-out tests were conducted on each specimen. The experimental results indicate that there are two types of axial load–slip curves for each specimen in four push-out tests. Moreover, comparison of the results of the push-out tests in the same direction shows that the bond failure load of the specimen decreases with the increase in the number of push-out tests. Based on the analysis of the test results, it is shown that the bond performance between the GFRP tube and the nano-CaCO3 concrete is better than that between the GFRP tube and the ordinary concrete. Furthermore, as the nano-CaCO3 concrete strength increases, the bond strength of the specimens decreases, indicating that the concrete strength has a negative effect on the bond strength. When the nano-CaCO3 concrete strength is relatively smaller (C20), the bond strength of the specimens decreases with the increase in the thickness of the GFRP tube. However, when the nano-CaCO3 concrete strength is relatively larger (C30 and C40), the bond strength of the specimens increases as the thickness of the GFRP tube increases.

Experimental Research on Interfacial Bond Performance in Rock Anchor with High-Performance Grouting Medium

2012 ◽  
Vol 517 ◽  
pp. 932-938 ◽  
Author(s):  
Zhi Fang ◽  
Hong Qiao Zhang
Keyword(s):  
Rock Mass ◽  
Bond Strength ◽  
High Performance ◽  
Interfacial Bond ◽  
Interfacial Bond Strength ◽  
Bond Performance ◽  
Pull Out ◽  
Steel Bar ◽  
Reactive Powder ◽  
Ground Anchor

There exist the problems such as low bond strength and bad durability in the ordinary grouting slurry of the ground anchor system at present. The high-performance grouting mediums RPC (Reactive Powder Concrete) and DSP (Densified Systems containing homogeneously arranged ultrafine Particles) would become the potential replacement of grouting medium in ground anchor resulting from their high compressive strength, durability and toughness. Based on a series of pull-out tests on ground anchors with different high-performance grouting medium of RPC and DSP , different bond length in the construction field, the bond performance on the interfaces between anchor bolt (deformed steel bar) and grouted medium as well as between grouted medium and rock mass was studied. The results indicate that the interfacial bond strength between RPC or DSP and deformed steel bolt ranges within 23-31Mpa, far greater than that (about 2-3MPa) between the ordinary cementitious grout and deformed steel bar. Even though the interfacial bond strength between the grouted medium and rock mass of limestone was not obtained in the test since the failure mode was pull-out of those steel bar rather than the interface shear failure between grouted medium and rock mass, the bond stress on the interface reached 6.2-8.38 MPa, also far greater than the bond strength (about 0.1-3MPa) between the ordinary cementitious slurry and rocks.

Experimental Study on Bond Behavior of GFRP-to-Cement Mortar

2011 ◽  
Vol 94-96 ◽  
pp. 543-546
Author(s):  
Ning Zhang ◽  
Ai Zhong Lu ◽  
Yun Qian Xu ◽  
Pan Cui
Keyword(s):  
Aluminium Alloy ◽  
Cement Mortar ◽  
Bond Stress ◽  
Reinforcing Bars ◽  
Bond Performance ◽  
Gfrp Bars ◽  
Pull Out ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Average Bond

Direct pull-out tests were performed to evaluate the bond performance of glass fiber-reinforced polymer (GFRP) reinforcing bars in cement mortar. Specimens with different bar diameters and different grouted lengths (i.e., 5d, 10d and 15d, d is the diameter of bars) are prepared for the pull-out tests. For comparison, specimens with plain aluminium alloy bars (AAB) were tested as well. The result shows that the average bond stress between plain aluminium alloy bars and cement is much smaller than that between the deformed GFRP bars and cement; thin GFRP bars tended to have larger average bond stress; the shorter the grouted length, the smaller the maximum average bond stress. Only part of grouted length undertakes the bond stress and the length depends on the shear modulus of GFRP and the surrounding material.

Utilizing alkali-activated materials as ordinary Portland cement replacement to study the bond performance of fiber-reinforced polymer bars in seawater sea-sand concrete

2022 ◽  
pp. 136943322110651
Author(s):  
Ruiming Cao ◽  
Bai Zhang ◽  
Luming Wang ◽  
Jianming Ding ◽  
Xianhua Chen
Keyword(s):  
Tensile Strength ◽  
Bond Strength ◽  
Ordinary Portland Cement ◽  
Concrete Strength ◽  
Fiber Reinforced Polymer ◽  
Bond Performance ◽  
Reinforced Polymer ◽  
Sea Sand ◽  
Frp Bars ◽  
Alkali Activated

Alkali-activated materials (AAMs) are considered an eco-friendly alternative to ordinary Portland cement (OPC) for mitigating greenhouse-gas emissions and enabling efficient waste recycling. In this paper, an innovative seawater sea-sand concrete (SWSSC), that is, seawater sea-sand alkali-activated concrete (SWSSAAC), was developed using AAMs instead of OPC to explore the application of marine resources and to improve the durability of conventional SWSSC structures. Then, three types of fiber-reinforced polymer (FRP) bars, that is, basalt-FRP, glass-FRP, and carbon-FRP bars, were selected to investigate their bond behavior with SWSSAAC at different alkaline dosages (3%, 4%, and 6% Na2O contents). The experimental results manifested that the utilization of the alkali-activated binders can increase the splitting tensile strength ( ft) of the concrete due to the denser microstructures of AAMs than OPC pastes. This improved characteristic was helpful in enhancing the bond performance of FRP bars, especially the slope of bond-slip curves in the ascending section (i.e., bond stiffness). Approximately three times enhancement in terms of the initial bond rigidity was achieved with SWSSAAC compared to SWSSC at the same concrete strength. Furthermore, compared with the BFRP and GFRP bars, the specimens reinforced with the CFRP bars experienced higher bond strength and bond rigidity due to their relatively high tensile strength and elastic modulus. Additionally, significant improvements in initial bond stiffness and bond strength were also observed as the alkaline contents (i.e., concrete strength) of the SWSSAAC were aggrandized, demonstrating the integration of the FRP bars and SWSSAAC is achievable, which contributes to an innovative channel for the development of SWSSC pavements or structures.

scholarly journals Effect of the degree of corrosion on bond performance of Cement Polymer Composite (CPC) Coated steel rebars

2018 ◽  
Vol 199 ◽  
pp. 04010
Author(s):  
Deepak K. Kamde ◽  
Radhakrishna G. Pillai
Keyword(s):  
Bond Strength ◽  
Polymer Composite ◽  
Continuous Monitoring ◽  
Coated Steel ◽  
Bond Performance ◽  
Pull Out ◽  
Curing Period ◽  
Uncoated Steel ◽  
Concrete Coating ◽  
Steel Rebars

Currently, large infrastructures (bridges, highways, etc.) are designed for more than 100 years. To achieve long service life, coated rebars (mostly, cement polymer composite (CPC) coated rebars) are being used to enhance the corrosion resistance. However, inadequately coated rebars can lead to premature corrosion. This can also affect the bond between the rebar and the concrete. To assess the effect of CPC coating on bond strength, pull-out specimens of (150×150×100) mm with 12 mm diameter rebar with 100 mm embedded length were cast and tested. For this, three replica specimens with two types of reinforcement namely, i) Uncoated steel ii) CPC coated steel were cast. To induce corrosion, additional five specimens with CPC coated steel rebars were cast with premixed chloride and cured for 28 days. During the curing period, continuous monitoring of corrosion potential and rate was done and degree of corrosion was assessed. The effect of degree of corrosion on bond of steel-concrete-coating interface was quantified. The CPC coated rebars without corrosion exhibited 10% bond reduction. CPC coated rebars with corrosion exhibited 30-70% reduction in bond strength. Also, the corrosion is found to adversely influence the stiffness of the bond.

Bond behavior of high strength concrete under reversed pull-out cyclic loading

2002 ◽  
Vol 29 (2) ◽  
pp. 191-200 ◽  
Author(s):  
M Alavi-Fard ◽  
H Marzouk
Keyword(s):  
Cyclic Loading ◽  
Bond Strength ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Displacement Curve ◽  
Bond Slip ◽  
Strength Concrete ◽  
Pull Out ◽  
Normal Strength

Structures located in seismic zones require significant ductility. It is necessary to examine the bond slip characteristics of high strength concrete under cyclic loading. The cyclic bond of high strength concrete is investigated under different parameters, including load history, confining reinforcement, bar diameter, concrete strength, and the rate of pull out. The bond strength, cracking, and deformation are highly dependent on the bond slip behavior between the rebar and the concrete under cyclic loading. The results of cyclic testing indicate that an increase in cyclic displacement will lead to more severe bond damage. The slope of the bond stress – displacement curve can describe the influence of the rate of loading on the bond strength in a cyclic test. Specimens with steel confinement sustained a greater number of cycles than the specimens without steel confinement. It has been found that the maximum bond strength increases with an increase in concrete strength. Cyclic loading does not affect the bond strength of high strength concrete as long as the cyclic slip is less than the maximum slip for monotonic loading. The behavior of high strength concrete under a cyclic load is slightly different from that of normal strength concrete.Key words: bond, high strength, cyclic loading, bar spacing, loading rate, failure mechanism.

scholarly journals Experimental study on the effect of concrete strength and corrosion level on bond between steel bar and concrete

2021 ◽  
Vol 72 (4) ◽  
pp. 498-509
Author(s):  
Vuong Doan Dinh Thien ◽  
Hung Nguyen Thanh ◽  
Hung Nguyen Dinh
Keyword(s):  
Compressive Strength ◽  
Bond Strength ◽  
Concrete Strength ◽  
Concrete Block ◽  
Bond Stress ◽  
Concrete Compressive Strength ◽  
Pull Out ◽  
Steel Bar ◽  
Stress Degradation ◽  
Slip Displacement

Corrosion of the steel reinforcement bars reduces the area of the steel bar and the bond stress between the steel bars and around concrete that decreases the capacity of concrete structures. In this study, the bond stress between steel bar with a diameter of 12mm and concrete was examined with the effect of different corrosion levels and different concrete grades. A steel bar was inserted in a concrete block with a size of 20×20×20cm. The compressive strength of concrete was 25.6MPa, 35.1MPa, and 44.1MPa. These specimens were soaked into solution NaCl 3.5% to accelerate the corrosion process with different corrosion levels in the length of 60mm. The pull-out test was conducted. Results showed that the bond strength of the corroded steel bar was higher than that predicted from CEB-FIP. Slip displacement and the range of slip displacement at the bond strength were reduced when the concrete compressive strength was increased. The rate of bond stress degradation occurred faster with the increment of the corrosion level when the concrete compressive strength was increased.

scholarly journals Experimental Assessment on the Flexural Bonding Performance of Concrete Beam with GFRP Reinforcing Bar under Repeated Loading

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Minkwan Ju ◽  
Hongseob Oh
Keyword(s):  
Bond Length ◽  
Repeated Loading ◽  
Variable Loading ◽  
Loading Test ◽  
Variable Amplitude Loading ◽  
Static Test ◽  
Variable Amplitude ◽  
Reinforcing Bar ◽  
Bond Performance ◽  
Bonding Performance

This study intends to investigate the flexural bond performance of glass fiber-reinforced polymer (GFRP) reinforcing bar under repeated loading. The flexural bond tests reinforced with GFRP reinforcing bars were carried out according to the BS EN 12269-1 (2000) specification. The bond test consisted of three loading schemes: static, monotonic, and variable-amplitude loading to simulate ambient loading conditions. The empirical bond length based on the static test was 225 mm, whereas it was 317 mm according to ACI 440 1R-03. Each bond stress on the rib is released and bonding force is enhanced as the bond length is increased. Appropriate level of bond length may be recommended with this energy-based analysis. For the monotonic loading test, the bond strengths at pullout failure after 2,000,000 cycles were 10.4 MPa and 6.5 MPa, respectively: 63–70% of the values from the static loading test. The variable loading test indicated that the linear cumulative damage theory on GFRP bonding may not be appropriate for estimating the fatigue limit when subjected to variable-amplitude loading.

Sign in / Sign up

Export Citation Format

Share Document