scholarly journals Study of the operation of a 110 MW combined-cycle power unit at minimum loads when operating on the wholesale electricity market

2020 ◽  
Vol 216 ◽  
pp. 01077
Author(s):  
George Marin ◽  
Dmitrii Mendeleev ◽  
Boris Osipov
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Power Unit ◽  
Electricity Market ◽  
Gas Turbines ◽  
Turbine Unit ◽  
Combined Cycle ◽  
Gas Turbine Unit ◽  
Combined Cycle Plant ◽  
Wholesale Electricity Market

Currently, all generating equipment with a capacity of more than 25 MW operates in the wholesale electricity market. The operation of combined cycle gas turbines is complicated by the implementation of daily load schedules. A distinctive feature of the operation of combined-cycle units is the presence of a gas and steam turbine in the cycle. In this paper, the variable operating modes of a combined cycle plant are considered. The minimum effective load of a gas and steam turbine is determined. An example of the real operation of a steam turbine that is included in a combined cycle plant 110 MW power unit at an operating combined heat and power is shown. The optimal minimum load of a combined cycle gas turbine unit has been determined. As a result of the research, the values of high and low pressure steam flow rates, fuel gas consumption, steam and gas turbine power were obtained. Based on the research results, the optimal minimum load of a combined cycle gas turbine unit was found - 40 MW. This load allows the main and auxiliary equipment to work without compromising reliability.

Performance Analysis of a Combined Cycle Power Plant Through Exergetic and Environmental Indices

2017 ◽  
Author(s):  
Edgar Vicente Torres González ◽  
Raúl Lugo Leyte ◽  
Martín Salazar Pereyra ◽  
Helen Denise Lugo Méndez ◽  
Miguel Toledo Velázquez ◽  
...  
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Environmental Indices ◽  
Combined Cycle Power Plant ◽  
Combustion Gases ◽  
Combined Cycle Plant ◽  
Exergetic Analysis ◽  
Gas Turbine Power Plant

In this paper is carried out a comparison between a gas turbine power plant and a combined cycle power plant through exergetic and environmental indices in order to determine performance and sustainability aspects of a gas turbine and combined cycle plant. First of all, an exergetic analysis of the gas turbine and the combined is carried out then the exergetic and environmental indices are calculated for the gas turbine (case A) and the combined cycle (case B). The exergetic indices are exergetic efficiency, waste exergy ratio, exergy destruction factor, recoverable exergy ratio, environmental effect factor and exergetic sustainability. Besides, the environmental indices are global warming, smog formation and acid rain indices. In the case A, the two gas turbines generate 278.4 MW; whereas 415.19 MW of electricity power is generated by the combined cycle (case B). The results show that exergetic sustainability index for cases A and B are 0.02888 and 0.1058 respectively. The steam turbine cycle improves the overall efficiency, as well as, the reviewed exergetic indexes. Besides, the environmental indices of the gas turbines (case A) are lower than the combined cycle environmental indices (case B), since the combustion gases are only generated in the combustion chamber.

Thermodynamic Rationale for Using Expander-Compressor Gas Turbine Power Unit

2021 ◽  
pp. 166-184
Author(s):  
A.S. Strebkov ◽  
A.V. Osipov ◽  
S.V. Zhavrotskiy
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Power Unit ◽  
Thermal Cycle ◽  
Turbine Unit ◽  
Negative Impact ◽  
Excess Pressure ◽  
Electricity Production ◽  
Gas Turbine Unit ◽  
Energy Potential

Natural gas is transported through a network of main gas pipelines under high pressure, and the process of its consumption requires a decrease in pressure of gas laid mainly in throttling devices. It is beneficial to use part of the available energy potential of natural gas for electricity production by means of expander-generator technologies. However, the task of finding ways to increase the capacity and efficiency of gas turbine power units using the energy of excess pressure of natural gas does not lose its relevance. The study poses and solves the problem of developing a new thermal cycle diagram of a combined power unit to substitute throttling pressure regulators at gas distribution stations with an expander-compressor gas turbine unit. A distinctive feature of the unit is the replacement of the gas turbine drive of the air compressor with its drive from the turbo-expander by using the energy of excess pressure of natural gas. This results in significant increase in the absolute thermal efficiency and decrease in the specific fuel and energy costs. We developed analytical dependencies relating the operating parameters of the expander-compressor gas turbine unit and its output characteristics. Thus, it was possible to find an approach to calculating the unit, the approach being based on proven methods for thermal cycle calculation. The results of the performed calculations show that, in comparison with gas turbine units, the expander-compressor gas turbine unit has a significantly lower specific consumption of equivalent fuel and a lower negative impact on the environment

Efficiency Analysis of Gas Turbine Combined-Cycle Fed with Synthetic Natural Gas (SNG) and Mixture of Syngas and SNG

2015 ◽  
Vol 656-657 ◽  
pp. 113-118
Author(s):  
Hsiu Mei Chiu ◽  
Po Chuang Chen ◽  
Yau Pin Chyou ◽  
Ting Wang
Keyword(s):  
Natural Gas ◽  
Simulation Model ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
System Level ◽  
Minimum Requirement ◽  
Synthetic Natural Gas ◽  
System Level Simulation

The effect of synthetic natural gas (SNG) and mixture of syngas and SNG fed to Natural Gas Combined-Cycle (NGCC) plants is presented in this study via a system-level simulation model. The commercial chemical process simulator, Pro/II®V8.1.1, was used in the study to build the analysis model. The NGCC plant consists of gas turbine (GT), heat recovery steam generator (HRSG) and steam turbine (ST). The study envisages two analyses as the basic and feasibility cases. The former is the benchmark case which is verified by the reference data with the GE 7FB gas turbine. According to vendor’s specification, the typical net plant efficiency of GE 7FB NGCC with two gas turbines to one steam turbine is 57.5% (LHV), and the efficiency is the benchmark in the simulation model built in the study. The latter introduces a feasibility study with actual parameters in Taiwan. The SNG-fed GE 7FB based combined-cycle is evaluated, and the mixture of SNG and syngas is also evaluated to compare the difference of overall performance between the two cases. The maximum ratio of syngas to SNG is 0.14 due to the constraint for keeping the composition of methane at a value of 80 mol%, to meet the minimum requirement of NG in Taiwan. The results show that the efficiency in either case of SNG or mixture of SNG and syngas is slightly lower than the counterpart in the benchmark one. Because the price of natural gas is much higher than that of coal, it results in higher idle capacity of NGCC. The advantage of adopting SNG in Taiwan is that it could increase the capacity factor of combined-cycles in Taiwan. The study shows a possible way to use coal and reduce the CO2emission, since coal provides nearly half of the electricity generation in Taiwan in recent years.

Advanced Gas Turbine and High Performance Gas-Steam Combined Cycle Plant With Blade Cooling Air Controlling

2006 ◽  
Author(s):  
Tadashi Tsuji
Keyword(s):  
Power Generation ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Hot Water ◽  
Blade Cooling ◽  
Combined Cycle Plant ◽  
Cooling Air

Air cooling blades are usually applied to gas turbines as a basic specification. This blade cooling air is almost 20% of compressor suction air and it means that a great deal of compression load is not converted effectively to turbine power generation. This paper proposes the CCM (Cascade Cooling Module) system of turbine blade air line and the consequent improvement of power generation, which is achieved by the reduction of cooling air consumption with effective use of recovered heat. With this technology, current gas turbines (TIT: turbine inlet temperature: 1350°C) can be up-rated to have a relative high efficiency increase. The increase ratio has a potential to be equivalent to that of 1500°C Class GT/CC against 1350°C Class. The CCM system is designed to enable the reduction of blade cooling air consumption by the low air temperature of 15°C instead of the usual 200–400°C. It causes the turbine operating air to increase at the constant suction air condition, which results in the enhancement of power and thermal efficiency. The CCM is installed in the cooling air line and is composed of three stage coolers: steam generator/fuel preheater stage, heat exchanger stage for hot water supplying and cooler stage with chilled water. The coolant (chilled water) for downstream cooler is produced by an absorption refrigerator operated by the hot water of the upstream heat exchanger. The proposed CCM system requires the modification of cooling air flow network in the gas turbine but produces the direct effect on performance enhancement. When the CCM system is applied to a 700MW Class CC (Combined Cycle) plant (GT TIT: 135°C Class), it is expected that there will be a 40–80MW increase in power and +2–5% relative increase in thermal efficiency.

Design of Fast and Reliable Steam Surface Condensers

2020 ◽  
Author(s):  
Ranga Nadig
Keyword(s):  
Steam Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Design Features ◽  
Surface Condenser ◽  
Combined Cycle Plant ◽  
Startup Time ◽  
On Line ◽  
To Come

Abstract Power plants operating in cyclic mode, standby mode or as back up to solar and wind generating assets are required to come on line on short notice. Simple cycle power plants employing gas turbines are being designed to come on line within 10–15 minutes. Combined cycle plants with heat recovery steam generators and steam turbines take longer to come on line. The components of a combined cycle plant, such as the HRSG, steam turbine, steam surface condenser, cooling tower, circulating water pumps and condensate pumps, are being designed to operate in unison and come on line expeditiously. Major components, such as the HRSG, steam turbine and associated steam piping, dictate how fast the combined cycle plant can come on line. The temperature ramp rates are the prime drivers that govern the startup time. Steam surface condenser and associated auxiliaries impact the startup time to a lesser extent. This paper discusses the design features that could be included in the steam surface condenser and associated auxiliaries to permit quick startup and reliable operation. Additional design features that could be implemented to withstand the demanding needs of cyclic operation are highlighted.

Steam-Cooled Gas Turbine Casings, Struts, and Disks in a Reheat Gas Turbine Combined Cycle: Part I—Compressor and Combustor

1983 ◽  
Vol 105 (4) ◽  
pp. 844-850 ◽  
Author(s):  
I. G. Rice
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Material Selection ◽  
Pressure Ratio ◽  
Industrial Applications ◽  
Combined Cycle ◽  
Tip Clearance ◽  
Turbine Output

High-cycle pressure-ratio (38–42) gas turbines being developed for future aircraft and, in turn, industrial applications impose more critical disk and casing cooling and thermal-expansion problems. Additional attention, therefore, is being focused on cooling and the proper selection of materials. Associated blade-tip clearance control of the high-pressure compressor and high-temperature turbine is critical for high performance. This paper relates to the use of extracted steam from a steam turbine as a coolant in a combined cycle to enhance material selection and to control expansion in such a manner that the cooling process increases combined-cycle efficiency, gas turbine output, and steam turbine output.

Simulations of Pressurized Fluidized Circulating Bed Based Combined Cycle (PFCB)

2014 ◽  
Author(s):  
Hossin Omar ◽  
Mohamed Elmnefi
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Compression Ratio ◽  
Steam Pressure ◽  
Combined Cycle ◽  
Flue Gases ◽  
First Case ◽  
Combined Cycle Plant ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency

The Pressurized Fluidized Circulating Bed (PFCB) combined cycle was simulated. The simulations balance the energy between the elements of the unit, which consists of gas turbine cycle and steam turbine cycle. The PFCB is used as a combustor and steam generator at the same time. The simulations were carried out for PFCB combined cycle plant for two cases. In the first case, the simulations were performed for combined cycle with reheat in the steam turbine cycle. While in the second case, the simulations were carried out for the PFCB combined cycle with extra combustor and steam turbine cycle with reheat. For both cases, the effect of steam inlet pressure on the combined cycle efficiency was predicted. It was found that increasing of steam pressure results in increase in the combined cycle thermal efficiency. The effect of the inlet flue gases temperature on the gas turbine and on the combined cycle efficiencies was also predicted. The maximum PFCB combined cycle efficiency occurs at a compression ratio of 18, which is the case of utilizing an extra combustor. The simulations were carried out for only one fuel composition and for a compression ratio ranges between 1 to 40.

scholarly journals Repowering of a Small Utility: A Unique Solution to a Unique Problem

1979 ◽  
Author(s):  
L. F. Fougere ◽  
H. G. Stewart ◽  
J. Bell
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Electric Utility ◽  
Combined Cycle ◽  
Steam Boiler ◽  
Heat Recovery Steam Generator ◽  
Turbine Generator

Citizens Utilities Company’s Kauai Electric Division is the electric utility on the Island of Kauai, fourth largest and westernmost as well as northernmost of the Hawaiian Islands. As a result of growing load requirements, additional generating capacity was required that would afford a high level of reliability and operating flexibility and good fuel economy at reasonable capital investment. To meet these requirements, a combined cycle arrangement was completed in 1978 utilizing one existing gas turbine-generator and one new gas turbine-generator, both exhausting to a new heat recovery steam generator which supplies steam to an existing steam turbine-generator. Damper controlled ducting directs exhaust gas from either gas turbine, one at a time, through the heat recovery steam generator. The existing oil-fired steam boiler remains available to power the steam turbine-generator independently or in parallel with the heat recovery steam generator. The gas turbines can operate either in simple cycle as peaking units or in combined cycle, one at a time, as base load units. This arrangement provides excellent operating reliability and flexibility, and the most favorable economics of all generating arrangements for the service required.

scholarly journals Effect of Turbine and Compressor Inlet Temperatures and Air Bleeding on the Comparative Performance of Simple and Combined Gas Turbine Unit

2020 ◽  
Vol 5 (12) ◽  
pp. 39-45
Author(s):  
Basharat Salim ◽  
Jamal Orfi ◽  
Shaker Saeed Alaqel
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Energy Demand ◽  
Power Plants ◽  
Turbine Unit ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Gas Turbine Unit ◽  
The World ◽  
Compressor Inlet

The proper utilization of all the available forms of energy resources has become imminent to meet the power requirement and energy demand in both the developed and developing countries of the world. Even though the emphasis is given to the renewable resources in most parts of the world, but fossil fuels will still remain the main resources of energy as these can meet both normal and peak demands. Saudi Arab has number of power plant based on natural gas and fuel that are spread in all its regions. These power plants have aeroderivative gas turbine units supplied by General Electric Company as main power producing units. These units work on dual fuel systems. These units work as simple gas turbine units to meat peak demands and as part of combined cycle otherwise. The subject matter of this study is the performance of one of the units of a power plant situated near Riyadh city of Saudi Arab. This unit also works both as simple gas turbine unit and as a part of combined cycle power plant unit. A parametric based performance evaluation of the unit has been carried out to study both energetic and exergetic performance of the unit for both simple and combined cycle operation. Effect of compressor inlet temperature, turbine inlet temperature, pressure ratio of the compressor, the stage from which bleed off air have been taken and percentage of bleed off air from the compressor on the energetic and exergetic performance of the unit have been studied. The study reveals that all these parameters effect the performance of the unit in both modes of operation.

Sign in / Sign up

Export Citation Format

Share Document