scholarly journals Influence of acid environment on Collapsibility of Loess

2021 ◽  
Vol 267 ◽  
pp. 02013
Author(s):  
Yao Zhang ◽  
Cheng Jin ◽  
Zaiqiang Hu ◽  
Ning Li ◽  
Yu Xi
Keyword(s):  
Acidic Solution ◽  
Test Results ◽  
Internal Factor ◽  
Time Scanning ◽  
Collapsible Loess ◽  
Before And After ◽  
Acid Environment ◽  
Stability Time ◽  
Coefficient Stability ◽  
Sensitive Pressure

Cemented connection of loess is an important internal factor of loess collapsibility, which has a direct impact on its collapsibility. In this study, different concentrations of nitric acid were added to the immersion solution of loess collapsibility test, and the collapsibility sensitivity indexes of loess, such as collapsibility coefficient, stability time and collapsibility rate, were tested under acidic environment and different pressures. At the same time, scanning electron microscope was used to observe the changes of pore and structure of soil samples before and after the test. The test results show that in acid solution, the collapsibility coefficient of collapsible loess increases more under low pressure, and the collapsibility stability time of collapsible loess increases under different pressures. Loess has different collapsibility sensitive pressure range in aqueous solution and acidic solution. The structural strength of collapsible loess has an important influence on the depth of collapsible loess.

scholarly journals Study on the collapsibility sensitivity of loess in different acid environment by consolidometer

2021 ◽  
Vol 267 ◽  
pp. 02069
Author(s):  
Yao Zhang ◽  
Cheng Jin ◽  
Ning Li ◽  
Zaiqiang Hu
Keyword(s):  
Acidic Solution ◽  
Structural Strength ◽  
Water Solution ◽  
Test Results ◽  
Internal Factor ◽  
Loess Area ◽  
Collapsible Loess ◽  
Acid Environment ◽  
Stability Time ◽  
Sensitive Pressure

Cement connection of loess is an important internal factor of loess collapse, which has a direct impact on the sensitivity of the collapse. In this study, different concentrations of nitric acid were added into the immersion water solution of loess collapsibility test. The collapsibility deformation and stability time were measured under different pressure and acid environment. The test results show that: in acid solution, the collapsibility coefficient of collapsible loess increases more under low pressure, and the collapsibility stability time is prolonged under all levels of pressure; Loess has different collapsibility sensitive pressure range in aqueous solution and acidic solution. The structural strength of collapsible loess has an important influence on the depth of collapsible loesr. It is very important to the constructions on the loess area

Sunlight exposure: the effects on the performance of paragliding fabric

2018 ◽  
Vol 69 (05) ◽  
pp. 381-389
Author(s):  
MENGÜÇ GAMZE SÜPÜREN ◽  
TEMEL EMRAH ◽  
BOZDOĞAN FARUK
Keyword(s):  
Mechanical Properties ◽  
Aging Process ◽  
Air Permeability ◽  
Sunlight Exposure ◽  
Test Results ◽  
Coating Materials ◽  
Strength Tests ◽  
Before And After ◽  
The Relationship ◽  
Dark Blue

This study was designed to explore the relationship between sunlight exposure and the mechanical properties of paragliding fabrics which have different colors, densities, yarn counts, and coating materials. This study exposed 5 different colors of paragliding fabrics (red, turquoise, dark blue, orange, and white) to intense sunlight for 150 hours during the summer from 9:00 a.m. to 3:00 p.m. for 5 days a week for 5 weeks. Before and after the UV radiation aging process, the air permeability, tensile strength, tear strength, and bursting strength tests were performed. Test results were also evaluated using statistical methods. According to the results, the fading of the turquoise fabric was found to be the highest among the studied fabrics. It was determined that there is a significant decrease in the mechanical properties of the fabrics after sunlight exposure. After aging, the fabrics become considerably weaker in the case of mechanical properties due to the degradation in both the dyestuff and macromolecular structure of the fiber

scholarly journals An Empirical Study on the Application of Cooperative Learning to Comprehensive English Classes in a Chinese Independent College

2017 ◽  
Vol 10 (2) ◽  
pp. 94
Author(s):  
Ji Meng
Keyword(s):  
Cooperative Learning ◽  
Empirical Study ◽  
Test Results ◽  
Independent College ◽  
Language Competence ◽  
English Classes ◽  
Academic Level ◽  
Before And After ◽  
Posttest Questionnaire ◽  
Positive Impacts

This research investigated a comparison between the effect of cooperative learning and lecture teaching on Comprehensive English classes in a Chinese Independent College. An empirical study for two semesters was carried out in the forms of pretest, posttest, questionnaire and interviews. While control class was taught in the conventional way, experiment class was instructed based on cooperative base groups with positive interdependence structured on purpose. Compared with traditional instructions, cooperative learning as pedagogy can improve students’ performance on course exams, but not necessarily their language competence as shown in national English competency tests taken before and after the experiement. Test results also indicate students from experiment class who excelled in competency test outnumbered those from control class, revealing that cooperative learning has positive impacts especially on students at a relatively higher academic level. Questionaire results show that students are most inclined to agree they have more chances to practice the language in a cooperative environment.

Characteristics of Phenomena in Powders Type RE2Zr2O7-Al2O3 in High Temperature Annealing Conditions

2011 ◽  
Vol 312-315 ◽  
pp. 583-588 ◽  
Author(s):  
Grzegorz Moskal ◽  
Lucjan Swadźba ◽  
Marek Hetmańczyk ◽  
Bartosz Witala
Keyword(s):  
High Temperature ◽  
Perovskite Oxide ◽  
Differential Scanning Calorimetric ◽  
Test Results ◽  
Dsc Analysis ◽  
Annealing Conditions ◽  
Before And After ◽  
Influence Of Temperature On ◽  
Dta Analysis ◽  
Type Bond

The paper presents test results and characterizes the structural stability of powders, which form a mixture of aluminium oxide (Al2O3) and gadolinium, based on rare earth zirconates. This mixture is provided to create thermal barrier coatings (TBCs) by spraying. The purpose of the tests was to determine the influence of temperature on reactions, occurring between those powders within a temperature range from 25°C to 1500°C, while such conditions were to simulate the conditions, which occur during creation of TBCs and they give an answer to the question concerning mutual reactivity of the powders. The requirements for new materials, provided to spray the TBCs, indicate the necessity to prepare the materials, which do not show tendency towards reactions with the Al2O3, formed during oxidation of Ni (Co) CrAlY, while this reaction is of type bond coat. The tests included differential scanning calorimetric (DSC) analysis and differential thermal analysis (DTA) of powder mixtures. Diffraction analysis was also performed before and after the tests have been finished. The DSC analysis results, obtained at a range of high temperature, did not show any thermal effects, which indicate a low level of mutual reactivity of the powders. However, the DTA analysis suggests presence of such effects at temperature close to 1300°C, and it indicates the necessity to verify exactly the obtained results. Results of the XRD measurement showed that after annealing process already at 1100°C the perovskite oxide of GdAlO3 was present.

scholarly journals Standardization of dot-ELISA for the serological diagnosis of toxocariasis and comparision of the assay with ELISA

1992 ◽  
Vol 34 (1) ◽  
pp. 55-60 ◽  
Author(s):  
Eide Dias Camargo ◽  
Paulo Mutuko Nakamura ◽  
Adelaide José Vaz ◽  
Marcos Vinícius da Silva ◽  
Pedro Paulo Chieffi ◽  
...  
Keyword(s):  
Low Cost ◽  
Clinical Signs ◽  
Toxocara Canis ◽  
Enzyme Linked Immunosorbent Assay ◽  
Serum Samples ◽  
Specific Antibodies ◽  
Normal Individuals ◽  
Before And After ◽  
Dot Elisa ◽  
Stability Time

The dot-enzyme-linked immunosorbent assay (dot-ELISA) was standardized using somatic (S) and excretory-secretory (ES) antigens of Toxocara-canis for the detection of specific antibodies in 22 serum samples from children aged 1 to 15 years, with clinical signs of toxocariasis. Fourteen serum samples from apparently normal individuals and 28 sera from patients with other pathologies were used as controls. All samples were used before and after absorption with Ascaris suum extract. When the results were evaluated in comparison with ELISA, the two tests were found to have similar sensitivity, but dot-ELISA was found to be more specific in the presence of the two antigens studied. Dot-ELISA proved to be effective for the diagnosis of human toxocariasis, presenting advantages in terms of yield, stability, time and ease of execution and low cost.

Effect of styrene–butadiene–styrene content on the adhesion properties of bitumen before and after heat aging

2008 ◽  
Vol 35 (5) ◽  
pp. 454-460 ◽  
Author(s):  
Krzysztof Zieliński
Keyword(s):  
Adhesion Strength ◽  
Test Results ◽  
Adhesion Properties ◽  
Before And After ◽  
Styrene Content ◽  
Styrene Butadiene Styrene ◽  
Styrene Butadiene ◽  
Steel Substrates ◽  
Butadiene Styrene

This article describes the effect of heat aging and styrene–butadiene–styrene (SBS) content in bitumen on the adhesion properties of mastics (bitumen-filler mix) to concrete and steel substrates. Test results showed that the adhesion strength of bituminous mastics to concrete and steel substrates decreased as the SBS content increased. Bitumen types modified with 9%–12% of SBS, commonly used in waterproofing materials, showed an approximately three times weaker bond with concrete and steel substrates than the nonmodified equivalents. Results also showed that after heat aging, the adhesion strength of the nonmodified bitumen was always higher than that of the unheated bitumen modified with 9%–12% of SBS.

POLICY OF PROMOTING ALCOHOL CONSUMPTION IN TIMES OF COVID-19 LOCKDOWN IN INDIA: A MEDICAL AND CONSTITUTIONAL ANALYSIS.

2021 ◽  
pp. 21-24
Author(s):  
Neha Sharma ◽  
Ayush Anand ◽  
Shreyas Joshi ◽  
Samrat Ray
Keyword(s):  
Mobile Application ◽  
Prospective Observational Study ◽  
Social Contact ◽  
Contact Tracing ◽  
Family Welfare ◽  
Cumulative Number ◽  
Test Results ◽  
Before And After ◽  
The Given ◽  
Constitutional Analysis

BACKGROUND: India, with the declaration of COVID-19 as a pandemic, started imposing restrictions in the country th and initiated a nationwide lockdown under Section 6 of the Disaster Management Act, 2005 on 24 March 2020, followed by four phases of lockdown and then gradual unlock of the country. The rationale behind the same was to avoid social contact. Alcohol dispensing was also stopped during this time and was among the rst services to be reopened by the States. We propose in this paper that this lifting of ban on alcohol sale during the pandemic has led to a signicant increase in the number of COVID-19 cases in the country. METHODS: This is a prospective, observational study, done by collecting data from the Aargya Setu App, which is a mobile application launched by the Ministry of Health and Family Welfare on 2 April 2020 for contact tracing and elf assessment of COVID-19. The data of cumulative number of cases in 12 selected states of the country were compared before and after the lift of ban of alcohol and signicance was shown by the paired t test. RESULTS: The number of COVID-19 positive cases in the country during nationwide lockdown with simultaneous ban on alcohol sale when compared to cumulative number of cases after the lift of ban of alcohol sale during Lockdown and initial Unlock is statistically signicant (p = 0.04) CONCLUSION: We found that the decision to restart the sale of Alcohol could have been a factor for rise in number of cases in the country in the given timeframe. The decision to start the sale has also not been in accordance with the Indian Constitution and against the nation's founding ethics.

scholarly journals Analisis Reaksi Pasar Terhadap Pengumuman Merger dan Akuisisi Pada Perusahaan Akuisitor yang Terdaftar di BEI

2018 ◽  
pp. 1870
Author(s):  
Ika Putri Adnyani ◽  
Gayatri Gayatri
Keyword(s):  
Abnormal Return ◽  
Trading Volume ◽  
Sampling Method ◽  
Stock Exchange ◽  
Cumulative Abnormal Return ◽  
Test Results ◽  
Volume Activity ◽  
Paired Sample ◽  
Analysis Technique ◽  
Before And After

This research is conducted on all acquisition companies that conduct acquisitions listed on Indonesia Stock Exchange 2011-2016 period. Sampling method using purposive sampling. The number of samples of this research is 50 companies. The market reaction in this study used abnormal return and trading volume activity. The testing of information content will be done by looking at differences in cumulative abnormal return and the average trading volume of shares five days before and five days after the announcement of the acquisition. Data analysis technique used is paired sample t-test. Based on the test results, found there are significant differences in the abnormal return of the acquirer company before and after the announcement of the acquisition. However, there is no difference in trading volume activity of the acquirer's stock before and after the acquisition announcement   Keywords: acquisitions, stock market, abnormal return, trading volume activity

scholarly journals In-plane Shear Strengthening of Unreinforced Masonry Walls Using GFRP Jacketing

2017 ◽  
Author(s):  
Enea Mustafaraj ◽  
Yavuz Yardim
Keyword(s):  
Experimental Results ◽  
Test Results ◽  
Compression Tests ◽  
Shear Strengthening ◽  
Plane Shear ◽  
Standard Size ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Diagonal Compression ◽  
Before And After

In this paper, it is presented the experimental results of a campaign on diagonal compression tests, as of ASTM E519-02, to assess and compare the in-plane behavior of standard size of 1200 × 1200 × 250 mm, for three unreinforced and three reinforced wall panels by glass fiber reinforced polymer (GFRP) embedded in an inorganic matrix.From the diagonal compression test results, were determined some of the main mechanical parameters such as: shear strength, modulus of rigidity and ductility, before and after application of the reinforcement.The experimental results showed that the GFRP reinforced panels exhibited a significant increase of 127% in shear resistance, 1100% in ductility and 650% in modulus of rigidity when compared to unreinforced panels.It was concluded that this technique provided satisfactory results and can be considered a suitable method for repair of masonry structures.

scholarly journals Effect of Temperature on the Tribological Properties of Selected Thermoplastic Materials Cooperating with Aluminium Alloy

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7318
Author(s):  
Anita Ptak ◽  
Paula Taciak ◽  
Wojciech Wieleba
Keyword(s):  
Aluminium Alloy ◽  
Contact Pressure ◽  
Tribological Properties ◽  
Polymer Materials ◽  
Effect Of Temperature ◽  
Test Results ◽  
Friction Process ◽  
Before And After ◽  
Pin On Disc ◽  
Two Parameters

This article concerns the tribological properties of three selected polymer materials: polyamide PA6, polyethylene PE-HD and polyetheretherketone composite PEEK/BG during sliding against aluminium alloy EN AW-2017A in the presence of hydraulic oil HLP 68. The tests were carried out under contact pressure p of 3.5–11 MPa at ambient temperature T ranging from −20 °C to +20 °C. The dependence of kinetic friction coefficient μk on the two parameters was determined through tribological tests carried out using a pin-on-disc tribometer. A five-level central composite rotatable design (CCRD) was adopted for the experiment. All the test results were statistically analysed. The microhardness of the surface of the polymeric material was measured before and after the friction process. The surface was also examined under SEM. Temperature and contact pressure have been found to have a significant effect on the tribological properties of the tested sliding pairs. Relative to the applied friction conditions, the surfaces after friction showed rather heavy signs of wear.

Sign in / Sign up

Export Citation Format

Share Document