scholarly journals Potential of hydrogen addition to natural gas or ammonia as a solution towards low- or zero-carbon fuel for the supply of a small turbocharged SI engine

2021 ◽  
Vol 312 ◽  
pp. 07022
Author(s):  
Alfredo Lanotte ◽  
Vincenzo De Bellis ◽  
Enrica Malfi
Keyword(s):  
Alternative Fuels ◽  
Laminar Flame ◽  
Combustion Engine ◽  
Numerical Study ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Si Engine ◽  
Hydrogen Addition ◽  
Emission Regulations ◽  
Zero Carbon

Nowadays there is an increasing interest in carbon-free fuels such as ammonia and hydrogen. Those fuels, on one hand, allow to drastically reduce CO2 emissions, helping to comply with the increasingly stringent emission regulations, and, on the other hand, could lead to possible advantages in performances if blended with conventional fuels. In this regard, this work focuses on the 1D numerical study of an internal combustion engine supplied with different fuels: pure gasoline, and blends of methane-hydrogen and ammonia-hydrogen. The analyses are carried out with reference to a downsized turbocharged two-cylinder engine working in an operating point representative of engine operations along WLTC, namely 1800 rpm and 9.4 bar of BMEP. To evaluate the potential of methane-hydrogen and ammonia-hydrogen blends, a parametric study is performed. The varied parameters are air/fuel proportions (from 1 up to 2) and the hydrogen fraction over the total fuel. Hydrogen volume percentages up to 60% are considered both in the case of methane-hydrogen and ammonia-hydrogen blends. Model predictive capabilities are enhanced through a refined treatment of the laminar flame speed and chemistry of the end gas to improve the description of the combustion process and knock phenomenon, respectively. After the model validation under pure gasoline supply, numerical analyses allowed to estimate the benefits and drawbacks of considered alternative fuels in terms of efficiency, carbon monoxide, and pollutant emissions.

scholarly journals 1D numerical study on hydrogen injection enabling ultra-lean combustion in a small gasoline Spark Ignition engine

2020 ◽  
Vol 197 ◽  
pp. 06001
Author(s):  
Luigi Teodosio ◽  
Dino Pirrello ◽  
Luca Marchitto
Keyword(s):  
High Efficiency ◽  
Laminar Flame ◽  
Numerical Study ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Pollutant Emissions ◽  
Numerical Code ◽  
Hydrogen Addition ◽  
1D Model ◽  
The Impact

This paper deals with the effects of hydrogen port injection on combustion evolution, efficiency and exhaust emissions of a small turbocharged gasoline Spark-Ignition engine through a 1D numerical code. First, the experiments on the base engine architecture are performed at different speeds and at low/medium loads. The experimental findings are used to validate a 1D model of the whole engine, developed within a commercial code. 1D model is also refined with “user-defined” sub-models for an accurate description of the in-cylinder phenomena, namely turbulence, combustion, heat transfer, and emissions. In a second step, 1D model is virtually modified through the installation of an hydrogen injector in each intake runner, while the combustion sub-model also accounts for the impact of hydrogen addition on the laminar flame speed through a dedicated correlation. 1D simulations are performed at low/medium loads and fixed speed of 2250 rpm with 5% of hydrogen by volume in the intake air. Numerical investigations show that hydrogen addition to gasoline/air mixtures allows relevant efficiency benefits (up to a maximum percent gain of 19%), while the NO emissions are almost eliminated. Consequently, hydrogen-boosted combustion represents a potential solution to achieve very high efficiency and reduced pollutant emissions of gasoline spark ignition engines equipped with a conventional combustion system.

Ethers and esters as alternative fuels for internal combustion engine: A review

2021 ◽  
pp. 146808742110464
Author(s):  
Yang Hua
Keyword(s):  
Alternative Fuels ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Engine Performance ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Future Research ◽  
Particulate Emissions ◽  
Ic Engine

Ether and ester fuels can work in the existing internal combustion (IC) engine with some important advantages. This work comprehensively reviews and summarizes the literatures on ether fuels represented by DME, DEE, DBE, DGM, and DMM, and ester fuels represented by DMC and biodiesel from three aspects of properties, production and engine application, so as to prove their feasibility and prospects as alternative fuels for compression ignition (CI) and spark ignition (SI) engines. These studies cover the effects of ether and ester fuels applied in the form of single fuel, mixed fuel, dual-fuel, and multi-fuel on engine performance, combustion and emission characteristics. The evaluation indexes mainly include torque, power, BTE, BSFC, ignition delay, heat release rate, pressure rise rate, combustion duration, exhaust gas temperature, CO, HC, NOx, PM, and smoke. The results show that ethers and esters have varying degrees of impact on engine performance, combustion and emissions. They can basically improve the thermal efficiency of the engine and reduce particulate emissions, but their effects on power, fuel consumption, combustion process, and CO, HC, and NOx emissions are uncertain, which is due to the coupling of operating conditions, fuel molecular structure, in-cylinder environment and application methods. By changing the injection strategy, adjusting the EGR rate, adopting a new combustion mode, adding improvers or synergizing multiple fuels, adverse effects can be avoided and the benefits of oxygenated fuel can be maximized. Finally, some challenges faced by alternative fuels and future research directions are analyzed.

A Numerical Study on the Influence of Hydrogen Addition on Soot Formation in a Laminar Aviation Kerosene (Jet A1) Flame at Elevated Pressure

2021 ◽  
Author(s):  
Mingshan Sun ◽  
Zhiwen Gan
Keyword(s):  
Volume Fraction ◽  
Soot Formation ◽  
Laminar Flame ◽  
Numerical Study ◽  
Soot Volume Fraction ◽  
Elevated Pressure ◽  
Condensation Process ◽  
Hydrogen Addition ◽  
Aviation Kerosene ◽  
Soot Precursor

Abstract The hydrogen addition is a potential way to reduce the soot emission of aviation kerosene. The current study analyzed the effect of hydrogen addition on aviation kerosene (Jet A1) soot formation in a laminar flame at elevated pressure to obtain a fundamental understanding of the reduced soot formation by hydrogen addition. The soot formation of flame was simulated by CoFlame code. The soot formation of kerosene-nitrogen-air, (kerosene + replaced hydrogen addition)-nitrogen-air, (kerosene + direct hydrogen addition)-nitrogen-air and (kerosene + direct nitrogen addition)-nitrogen-air laminar flames were simulated. The calculated pressure includes 1, 2 and 5 atm. The hydrogen addition increases the peak temperature of Jet A1 flame and extends the height of flame. The hydrogen addition suppresses the soot precursor formation of Jet A1 by physical dilution effect and chemical inhibition effect, which weaken the poly-aromatic hydrocarbon (PAH) condensation process and reduce the soot formation. The elevated pressure significantly accelerates the soot precursor formation and increases the soot formation in flame. Meanwhile, the ratio of reduced soot volume fraction to base soot volume fraction by hydrogen addition decreases with the increase of pressure, indicating that the elevated pressure weakens the suppression effect of hydrogen addition on soot formation in Jet A1 flame.

scholarly journals Effect of Fuel and Air Dilution on Syngas Combustion in an Optical SI Engine

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1566 ◽  
Author(s):  
S.D. Martinez-Boggio ◽  
S.S. Merola ◽  
P. Teixeira Lacava ◽  
A. Irimescu ◽  
P.L. Curto-Risso
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Process ◽  
Visible Spectrum ◽  
Propagation Speed ◽  
Fuel Mixture ◽  
Operating Conditions ◽  
Inert Gases ◽  
Pollutant Emissions ◽  
Si Engine ◽  
Lean Burn

To mitigate the increasing concentration of carbon dioxide in the atmosphere, energy production processes must change from fossil to renewable resources. Bioenergy utilization from agricultural residues can be a step towards achieving this goal. Syngas (fuel obtained from biomass gasification) has been proved to have the potential of replacing fossil fuels in stationary internal combustion engines (ICEs). The processes associated with switching from traditional fuels to alternatives have always led to intense research efforts in order to have a broad understanding of the behavior of the engine in all operating conditions. In particular, attention needs to be focused on fuels containing relatively high concentrations of hydrogen, due to its faster propagation speed with respect to traditional fossil energy sources. Therefore, a combustion study was performed in a research optical SI engine, for a comparison between a well-established fuel such as methane (the main component of natural gas) and syngas. The main goal of this work is to study the effect of inert gases in the fuel mixture and that of air dilution during lean fuelling. Thus, two pure syngas blends (mixtures of CO and H2) and their respective diluted mixtures (CO and H2 with 50vol% of inert gases, CO2 and N2) were tested in several air-fuel ratios (stoichiometric to lean burn conditions). Initially, the combustion process was studied in detail by traditional thermodynamic analysis and then optical diagnostics were applied thanks to the optical access through the piston crown. Specifically, images were taken in the UV-visible spectrum of the entire cycle to follow the propagation of the flame front. The results show that hydrogen promotes flame propagation and reduces its distortion, as well as resulting in flames evolving closer to the spark plug. All syngas blends show a stable combustion process, even in conditions of high air and fuel dilution. In the leanest case, real syngas mixtures present a decrease in terms of performance due to significant reduction in volumetric efficiency. However, this condition strongly decreases pollutant emissions, with nitrogen oxide (NOx) concentrations almost negligible.

scholarly journals Some aspects of cycle variability at the Diesel engine fuelled with animal fats

2019 ◽  
Vol 112 ◽  
pp. 01014
Author(s):  
Adrian Nicolici ◽  
Constantin Pană ◽  
Niculae Negurescu ◽  
Alexandru Cernat ◽  
Cristian Nuţu
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Experimental Investigations ◽  
Maximum Pressure ◽  
Content Increase ◽  
Animal Fats ◽  
Viable Solution

The progressive diminution of the oil reserves all over the world highlights the necessity of using alternative fuels derived from durable renewable resource. The use of the alternative fuels represents a viable solution to reduce the pollutant emissions and to replace fossil fuels. Thus, a viable solution is the use of the animal fats in mixture with the diesel fuel at the diesel engines. A D2156 MTN8 diesel engine was firstly fuelled with diesel fuel and then with different blends of diesel fuel-animal fats (5% and 10% animal fats content). In the paper are presented some results of the experimental investigations of engine fuelled with preheated animal fats. The raw animal fats effects on the combustion process and on the pollutant emissions at different engine loads and 1450 rev/min engine speed are showed. The engine cycle variability increases at the animal fats content increase. The cycle variability for maximum pressure, maximum pressure angle and indicated mean effective pressure is analysed. The cycle variability coefficients values don’t exceed the recommended values of the standard diesel engine.

scholarly journals Combustion of Hydrogen Enriched Methane and Biogases Containing Hydrogen in a Controlled Auto-Ignition Engine

2018 ◽  
Vol 8 (12) ◽  
pp. 2667
Author(s):  
Antonio Mariani ◽  
Andrea Unich ◽  
Mario Minale
Keyword(s):  
Equivalence Ratio ◽  
Numerical Study ◽  
Chemical Reactivity ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Ignition Process ◽  
Effective Pressure ◽  
Indicated Mean Effective Pressure ◽  
Auto Ignition ◽  
Combustion Of Hydrogen

The paper describes a numerical study of the combustion of hydrogen enriched methane and biogases containing hydrogen in a Controlled Auto Ignition engine (CAI). A single cylinder CAI engine is modelled with Chemkin to predict engine performance, comparing the fuels in terms of indicated mean effective pressure, engine efficiency, and pollutant emissions. The effects of hydrogen and carbon dioxide on the combustion process are evaluated using the GRI-Mech 3.0 detailed radical chain reactions mechanism. A parametric study, performed by varying the temperature at the start of compression and the equivalence ratio, allows evaluating the temperature requirements for all fuels; moreover, the effect of hydrogen enrichment on the auto-ignition process is investigated. The results show that, at constant initial temperature, hydrogen promotes the ignition, which then occurs earlier, as a consequence of higher chemical reactivity. At a fixed indicated mean effective pressure, hydrogen presence shifts the operating range towards lower initial gas temperature and lower equivalence ratio and reduces NOx emissions. Such reduction, somewhat counter-intuitive if compared with similar studies on spark-ignition engines, is the result of operating the engine at lower initial gas temperatures.

Numerical Simulation for the Preliminary Design of Fuel Flexible Stationary Gas Turbine Combustors Using Conventional and Alternative Fuels

2012 ◽  
Author(s):  
Washington Orlando Irrazabal Bohorquez ◽  
João Roberto Barbosa ◽  
Rob Johan Maria Bastiaans ◽  
Philip de Goey
Keyword(s):  
Numerical Simulation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
High Efficiency ◽  
Numerical Study ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Gas Turbine Combustor ◽  
Primary Zone

Currently, high efficiency and low emissions are most important requisites for the design of modern gas turbines due to the strong environmental restrictions around the world. In the past years, alternative fuels have been considered for application in industrial gas turbines. Therefore, combustor performance, pollutant emissions and the ability to burn several fuels became of much concern and high priority has been given to the combustor design. This paper describes a methodology focused on the design of stationary gas turbines combustion chambers with the ability to efficiently burn conventional and alternative fuels. A simplified methodology is used for the calculations of the equilibrium temperature and chemical species in the primary zone of a gas turbine combustor. Direct fuel injection and diffusion flames, together with numerical methods like Newton-Raphson, LU Factorization and Lagrange Polynomials, are used for the calculations. Diesel, ethanol and methanol fuels were chosen for the numerical study. A computer code sequentially calculates the main geometry of the combustor. From the numerical simulation it is concluded that the basic gas turbine combustor geometry, for some operating conditions and burning diesel, ethanol or methanol, are of similar sizes, because the development of aerodynamic characteristics predominate over the thermochemical properties. It is worth to note that the type of fuel has a marked effect on the stability and combustion advancement in the combustor. This can be seen when the primary zone is analyzed under a steady-state operating condition. At full power, the pressure is 1.8 MPa and the temperature 1,000 K at the combustor inlet. Then, the equivalence ratios in the primary zone are 1.3933 (diesel), 1.4352 (ethanol) and 1.3977 (methanol) and the equilibrium temperatures for the same operating conditions are 2,809 K (diesel), 2,754 K (ethanol) and 2,702 K (methanol). This means that the combustor can reach similar flame stability conditions, whereas the combustion efficiency will require richer fuel/air mixtures of ethanol or methanol are burnt instead of diesel. Another important result from the numerical study is that the concentration of the main pollutants (CO, CO2, NO, NO2) is reduced when ethanol or methanol are burnt, in place of diesel.

scholarly journals Numerical study for the spray characteristics of diesel engine powered by biodiesel fuels under different injection pressures

2021 ◽  
Author(s):  
Mohamed F. Al-Dawody ◽  
◽  
Khaled A. Al-Farhany ◽  
Naseer H. Hamza ◽  
Dhafer A. Hamzah ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Combustion Engine ◽  
Numerical Study ◽  
Combustion Process ◽  
Simulation Software ◽  
Spray Angle ◽  
Large Momentum ◽  
Biodiesel Fuels ◽  
Injection Pressures

Great attention is directed towards the study of the spray phenomena theoretically and experimentally due to its dramatic effect on the combustion process that occurred in an internal combustion engine, in particular, the diesel engine. The spray macroscopic characteristic of diesel engines fueled with two different biodiesel fuels in addition to nominal diesel under various injection pressures has been investigated numerically in this work. The selected biofuels are Rapeseed methyl ester (RME), Waste cooking oil methyl ester (WCOME). The Russian simulation software Diesel-RK is used in this work. Four different injection pressures are used which are 200, 500, 800 and 1000 bar respectively. It is found that RME has higher spray penetration with a narrow spray angle due to high viscosity and large momentum compared to diesel fuel. The results reported that biodiesels have greater Sauter mean diameter (SMD) compared to pure diesel because of their higher viscosity and surface tension. Promising reduction in SMD comes with WCOME as the injection pressure increases. Cylinder pressure along with heat release is reduced in the case of biodiesel due to the reduction in heating values. The lowest ability to produce smoke is recorded for WCOME where 93% reduction is achieved followed by a 57% reduction for RME as compared to diesel. The obtained results are compared with the results of other researcher and the convergence between them is observed.

scholarly journals Researches on Soot Filtration Process by Comparing Simulation and Experimental Tests

2021 ◽  
Vol 44 (4) ◽  
pp. 54-59
Author(s):  
Bogdan Manolin JURCHIȘ
Keyword(s):  
Particle Filter ◽  
Combustion Engine ◽  
Combustion Process ◽  
Engine Performance ◽  
Experimental Tests ◽  
Point Of View ◽  
Pollutant Emissions ◽  
Particulate Filter ◽  
The Creation ◽  
Two Stages

In this paper, the main objective of using numerical simulation was to highlight and analyse details that are very difficult to highlight through experimental tests. The development of the simulation model was also done for predictive purposes. In other words, after validation of the model, it can be used to estimate the filter load in other conditions than the experimental ones, respectively to evaluate how the particulate filter affects the operation of the internal combustion engine. In order to achieve the desired result, the creation of the model was done in two stages, the first stage was the creation of a model containing all the components of the engine, except the particle filter in order to identify the parameters of the combustion process and pollutant emissions - model validated on the basis of the indicated pressure curves, and the second stage was to complete the initial model with a particle filter and validate it from the point of view of the pressure drop, respectively of the engine performance, the aim was to obtain a trend, respectively values similar to the experimental ones.

scholarly journals Performances of a Research CFR Octane Rating Unit Engine and Dacia Single Cylinder SI Engine Ignited by a LASER System

2019 ◽  
Vol 112 ◽  
pp. 01009
Author(s):  
Bogdan George Done ◽  
Ion Copae
Keyword(s):  
New Technologies ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Laser Medium ◽  
Si Engine ◽  
Engine Operation ◽  
Single Cylinder ◽  
Spark Plug ◽  
Octane Rating ◽  
Laser Spark

At this time, the severe legislation regarding the level limits of the waste and exhaust gases released by thermal engines and also the necessity of engines efficiency improvement boost the engine research domain to bring in front the use of new technologies that can be used to control the in-cylinder combustion process. Now, the new technologies is represented by LASER spark plug systems which can be successfully used at petrol engines. LASER spark plug technology can have many advantages for engine operation control, an ignition system that could provide improved combustion is the one using plasma generation and a Q-switched LASER that results in pulses with high MW power. The LASER spark plug device used in the current research was a LASER medium Nd:YAG/Cr4+:YAG ceramic structure made up of a 8.0-mm long, 1.0-at.% Nd:YAG ceramic, optically-bonded to a Cr4+:YAG c. It was developed and constructed similar to classical spark plug and could be assembled on a CFR Octane Rating Unit Engine as well as on a Dacia Single Cylinder SI Engine which led to several results among which: influences on in-cylinder pressure, combustion and pollutant emissions.

Sign in / Sign up

Export Citation Format

Share Document