scholarly journals Seismic Analysis of Floating Stone Columns in Soft Clayey Soil

2021 ◽  
Vol 318 ◽  
pp. 01008
Author(s):  
Mahdi O. Karkush ◽  
Amer G. Jihad ◽  
Karrar A. Jawad ◽  
Mustafa S. Ali ◽  
Bilal J. Noman
Keyword(s):  
Clayey Soil ◽  
Seismic Analysis ◽  
Lateral Displacement ◽  
Soft Soil ◽  
Soft Clay ◽  
Surface Displacement ◽  
Stone Columns ◽  
Stone Column ◽  
Plastic Behavior ◽  
Ground Acceleration

The response of floating stone columns of different lengths to diameter ratio (L/D = 0, 2, 4, 6, 8, and 10) ratios exposed to earthquake excitations is well modeled in this paper. Such stone column behavior is essential in the case of lateral displacement under an earthquake through the soft clay soil. ABAQUS software was used to simulate the behavior of stone columns in soft clayey soil using an axisymmetric finite element model. The behavior of stone column material has been modeled with a Drucker-Prager model. The soft soil material was modeled by the Mohr-Coulomb failure criterion assuming an elastic-perfectly plastic behavior. The floating stone columns were subjected to the El Centro earthquake, which had a magnitude of 7.1 and a peak ground acceleration of 3.50 m/s2. The surface displacement, velocity, and acceleration in soft clayey enhanced by floating stone columns are also smaller than in natural soft clay. The findings of this research revealed that under the influence of earthquake waves, lateral displacement varies with stone columns of various lengths.

scholarly journals Comparison between unit cell and plane strain models of stone column ground improvement

2018 ◽  
Vol 7 (2) ◽  
pp. 263
Author(s):  
Maryam Gaber ◽  
Anuar Kasa ◽  
Norinah Abdul Rahman ◽  
Jamal Alsharef
Keyword(s):  
Stress Concentration ◽  
Plane Strain ◽  
Clayey Soil ◽  
Cell Model ◽  
Ground Improvement ◽  
Soft Soil ◽  
Unit Cell ◽  
Stone Columns ◽  
Stone Column ◽  
The Impact

This article presents a comparative study of the behaviour of clayey soil reinforcements using stone column ground improvement by means of numerical analyses. Two-dimensional finite element analyses with commercially available software, PLAXIS, were performed on end-bearing stone columns using 15-noded triangular elements to investigate the impact of the modelling type on the stress concentration ratio and failure mechanism of an improved foundation system. Consolidation analyses were conducted throughout the study using Mohr-Coulomb’s criterion. The computed values of the stress concentration ratios were compared for different key parameters, including the diameters of stone columns, c/c spacing of columns, friction angle of stone column material, and undrained cohesion of soft soil. The major conclusions of this study were that the stone column in the unit cell model shared between 2.5 to 3.14 times more loads than the surrounding soil, whilst in the plane strain model it shared between 1.7 to 2.9 times more loads. The use of plane strain approach to model the stone column gave a more comprehensive representation of the stress distribution and load transfer between the soil and columns, in addition to being a better method than the unit cell concept to evaluate the failure mode in this system.

Improvement of Soft Soil by Stone Column Treated with Bentonite

2020 ◽  
Vol 857 ◽  
pp. 283-291
Author(s):  
Safa Hussain Abid Awn ◽  
Jasim M. Abbas
Keyword(s):  
Clayey Soil ◽  
Slenderness Ratio ◽  
Soft Soil ◽  
Field Tests ◽  
Stone Column ◽  
Laboratory Model ◽  
Mix Proportion ◽  
Effective Depth ◽  
Concrete Footing ◽  
The Ideal

Soft clayey soils cover wide Iraqi areas specially the regions close to rivers and the southern part of this country Heavy weight structures like: highways, dams, multiple story buildings are suffering unacceptable settlement, when constructing on soft soils. The high contamination of water in such soils decrease the effective stress and reduce bearing capacity. The need was appeared to improve such problematic soil by the use of new technique of stone column treated with different percentages of natural bentonite by a series of field tests using full scale concrete footing constructed on soft soil in addition to a laboratory model to investigate settlement with time at constant stress. The soil that used in this study is natural clayey soil, brought from a location south of Diyala governorate, from a farm area. The study includes also: The effect of stone column diameter treated with bentonite on the behavior of footing constructing on soft clayey soil, The effect of stone column length on the behavior of footing on such soils. Results of field and laboratory model tests reviled that the treated model by stone column mixed with 40% bentonite is the ideal one, which reduces the settlement by 55%. In other hand problems of uneven settlements appear when using 60% bentonite as a mix proportion. The Ideal slenderness ratio (Ds/Ls<25%). The effective depth of stone column treated with bentonite is (1/3H).

EFFECT OF REPLACING CRUSHED STONE IN STONE COLUMNS BY WASTE MATERIAL ON SOIL IMPROVEMENT RATIO

2020 ◽  
Vol 7 (1) ◽  
Author(s):  
Nahla Mohammed Salim ◽  
Shatha Hasan ◽  
Kawther Al-Soudany
Keyword(s):  
Bearing Capacity ◽  
Soft Clay ◽  
Soil Improvement ◽  
Waste Material ◽  
Stone Columns ◽  
Crushed Stone ◽  
Stone Column ◽  
University Of Technology ◽  
The University ◽  
Building Demolition

Many researchers’ studies have shown that stone column is the best material to use to improve the bearing capacity of clayey soils. There are millions of waste volumes resulting from daily human activities. This excess waste leads to disposal problems and also causes environmental contamination and health risks. Demolished concrete is such one waste material that is produced from building demolition in Baghdad, Iraq. This paper describes experimental work conducted at the University of Technology that was carried out to investigate the improved bearing capacity of soft clay using crushed stone, followed by replacing crushed stone with concrete waste with the same relative density and grain size. The replacement was carried using waste concrete with different percentages corresponding to 25%, 50%, 75%, and 100%. The main conclusion drawn is that the bearing capacity increased to 119% by using crushed stone column, while the bearing capacity increased to 155% by using 100% of crushed concrete waste.

scholarly journals Stability analysis of roadway embankments supported by stone columns with the presence of water table under short-term and long-term conditions

2018 ◽  
Vol 162 ◽  
pp. 01013 ◽  
Author(s):  
Shaymaa Tareq Kadhim ◽  
Ziad Bashar Fouad
Keyword(s):  
Water Table ◽  
Factor Of Safety ◽  
Soft Soil ◽  
Stone Columns ◽  
Stone Column ◽  
Stability Factor ◽  
Short Term ◽  
Long Term Conditions ◽  
The Stability

Use of stone column technique to improve soft foundation soils under roadway embankments has proven to increase the bearing capacity and reduce the potential settlement. The potential contribution of stone columns to the stability of roadway embankments against general (i.e. deep-seated) failure needs to be thoroughly investigated. Therefore, a two-dimensional finite difference model implemented by FLAC/SLOPE 7.0 software, was employed in this study to assess the stability of a roadway embankment fill built on a soft soil deposit improved by stone column technique. The stability factor of safety was obtained numerically under both short-term and long-term conditions with the presence of water table. Two methods were adopted to convert the three-dimensional model into plane strain condition: column wall and equivalent improved ground methods. The effect of various parameters was studied to evaluate their influence on the factor of safety against embankment instability. For instance, the column diameter, columns’ spacing, soft soil properties for short-term and long-term conditions, and the height and friction angle of the embankment fill. The results of this study are developed in several design charts.

Study on the Lateral Displacement of Super-Long Pile under a Asymmetrical Surcharge Load in Soft Clay

2014 ◽  
Vol 580-583 ◽  
pp. 733-737
Author(s):  
Qi Li ◽  
Xiao Li Lu
Keyword(s):  
Lateral Displacement ◽  
Soft Soil ◽  
Soft Clay ◽  
Three Dimensional ◽  
Influence Factors ◽  
Major Influence ◽  
Small Contribution ◽  
Practical Engineering ◽  
Surcharge Load ◽  
Building Load

The pile will have a large lateral displacement in soft soil under the role of heaped load. Based on Biot consolidation theory, combined with a certain highway project, a three-dimensional FEM model is established, the process that the soil lateral deformation under heaped load lead to the pile side displacement was simulated. On the ground of the former result, the influence factors for the displacement of pile top and the pile displacement field distribution are analysed. The results show that, the building load area, load grade and the distance from loading area to pile have a major influence on the pile side displacement. On the other hand, the load on pile top have a very small contribution for stability of anti side displacement. The buildings nearby the area of pile foundation should be given attention in practical engineering.

scholarly journals Investigation of the Effect of Dimensional Characteristics of Stone Column on Load-Bearing Capacity and Consolidation Time

2018 ◽  
Vol 4 (6) ◽  
pp. 1437 ◽  
Author(s):  
Mohammad Reza Mohtasham ◽  
Mahdi Khodaparast
Keyword(s):  
Bearing Capacity ◽  
Clayey Soil ◽  
Stone Columns ◽  
Stone Column ◽  
Rigid Foundation ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Soil Subsidence ◽  
Behavioural Model ◽  
Consolidation Time

One of the best methods for rehabilitating loos and soft soils is the application of stone columns. This method enhances the soil properties by increasing its load-bearing capacity, decreasing the soil subsidence, and accelerating the consolidation rate. In the present paper, numerical analysis of a stone column of 10 m in length into a clayey soil using ABAQUS software is presented. The stone column was modelled based on the concept of unit cell, i.e. a single stone column with the surrounding soil. In this respect, material of the stone column was modelled using the elastoplastic behavioural model of Mohr-Coulomb, while Cam Clay behavioural model was used for the surrounding clayey soil. Furthermore, throughout the analyses performed in this study, effects of different parameters (e.g. applied load on rigid foundation, and the stone column length and diameter) on the subsidence and consolidation time of the rigid foundation were examined. The results indicated that, construction of a stone column into clayey soil decreases the subsidence and consolidation time of the soil considerably. In additions, increases in length and diameter of the stone column were found to significantly contribute to reduced subsidence and consolidation time of soil.

scholarly journals Behavior of foundation soil improved by stone column under cyclic load

2018 ◽  
Vol 239 ◽  
pp. 05015 ◽  
Author(s):  
Kwa Sally Fahmi ◽  
Mohammed Fattah ◽  
Alena Shestakova
Keyword(s):  
Finite Element ◽  
Cyclic Load ◽  
Soft Soil ◽  
Current Method ◽  
Stone Columns ◽  
Elastic Response ◽  
Stone Column ◽  
Finite Element Analyses ◽  
Foundation Soil ◽  
Rate Of Loading

This paper deals with using the stone column as a technique for the enhancement of the soft ground. The key goal of utilizing stone column is to decrease settlement and to increment the soil bearing ability, as well as decreasing the consolidation period. Nowadays, the current method concerns with various kinds of soil granular and cohesive. It is clear that the delicate soils (cohesive) possess a good settlement because of the disability of the ground to control the sidelong development and protruding of the stone sections. Moreover, the ways of utilization of the geosynthetic materials for encasement of the stone sections are other perfect ways to enhance the implementation, the quality, and firmness of stone segments. The present work investigates the behavior of the soft soil reinforced with ordinary and encased stone columns with geogrid under cyclic load. Six model tests were carried out on a soil with shear strength of about 15 kPa for both ordinary stone columns (OSC) and geogrid encased stone columns (ESC). For validating the enhanced method of utilizing stone columns, finite element model using the software PLAXIS 3D and field load exams had been applied. It was concluded that the models subjected to cyclic loading under the rate of loading 10 mm/sec reached the failure level faster than models tested under the rate of loading 5 mm/sec. The results of the finite element analyses of settlement compared with the records of settlement after the laboratory load tests seem to yield reasonably comparable values up to 50% of the design load. Afterwards, the recorded settlements show up to 60% higher values in compare with the results of the finite element analyses. This observation can be attributed to the occurrence of plastic failures under increasing load after an initial elastic response.

Experimental and Statistical Study on Single and Groups of Stone Columns

2020 ◽  
Vol 857 ◽  
pp. 399-408
Author(s):  
Maki J. Mohammed Al-Waily ◽  
Mohammed Y. Fattah ◽  
Maysa Salem Al-Qaisi
Keyword(s):  
Shear Strength ◽  
Stress Concentration ◽  
Bearing Capacity ◽  
Soft Clay ◽  
Undrained Shear Strength ◽  
Stone Columns ◽  
Stone Column ◽  
Dependent Variables ◽  
Undrained Shear ◽  
Improvement Ratio

In the present study, 24 laboratory models on soft clay treated with stone columns were carried out. The results for each case are analysed for the purpose of constructing a statistical model linking the variables studied. The experiments showed that the stress concentration and bearing capacity of soil treated with stone column increase with increasing the undrained shear strength (cu), number of columns and L/d ratio. The models represent a single stone column and a group of stone columns. The studied variables are three dependent variables, the stress concentration ratio (n), bearing capacity of soil treated with stone column (q) and the settlement improvement ratio (Sr) due to the existence of stone columns. The independent variables are six: the undrained shear strength of clay soil, with three values (6, 9 and 12 kPa), the number of stone columns (1, 2, 3 and 4 columns) and the length (L) to the diameter (D) of the stone column or (L/D) ratio in two values (6 and 8). Besides, the bearing capacity of the soil treated (q) with stone columns and the settlement improvement ratio were used in some statistical models as independents. After regression analysis, a set of equations that correlate the previous variables have been suggested. The incepted values for dependent variables are close to the laboratory results.

Analysis on Deep Excavation in Soft Soil Located on Sloped Bedrock

2012 ◽  
Vol 170-173 ◽  
pp. 13-19
Author(s):  
Shong Loong Chen ◽  
Cheng Tao Ho
Keyword(s):  
Lateral Displacement ◽  
Retaining Wall ◽  
Soft Soil ◽  
Soft Clay ◽  
Observation Data ◽  
Clay Layer ◽  
Deep Excavation ◽  
Element Analysis ◽  
2D Strain ◽  
Significant Difference

Deep excavations in soft-clay layer on sloped bedrock often leads to lateral displacement on retaining structures and uneven settlement due to unbalanced pressure generated from excavation. A construction project for which an excavation was complete in soft clay layer on sloped bedrock in Taipei City was adopted in the study. It is learned from the observation logs of the studied case that a significant difference exists in the lateral displacement of diaphragm wall and settlement between up and down-slope sides of sloped bedrock. Deep excavation is in fact profoundly complicated interaction between excavation strutting and soil. In general practice, the design of excavation is frequently simplified as a 2D strain behavior. However, the actual excavation on sloped bedrock is quite different from 1D or 2D simulation in a symmetric manner. Therefore, 2D finite element analysis program, PLAXIS, is introduced for the analysis on the behaviors of soil clay layer on sloped bedrock in excavation. The result is compared with onsite observation data, including displacement of retaining wall, settlement, axial loads of struts and others. The result of retaining wall displacement analysis is found consistent with the trend derived from onsite observation, which is possible for reference of similar engineering analyses and designs in the future.

Field performance of the port of Sepetiba test fills

1995 ◽  
Vol 32 (1) ◽  
pp. 106-121 ◽  
Author(s):  
Vinod K. Garga ◽  
Luciano V. Medeiros
Keyword(s):  
Ground Improvement ◽  
Soft Soil ◽  
Soft Clay ◽  
Field Performance ◽  
Stone Columns ◽  
Field Investigations ◽  
Large Program ◽  
Soil Deposits ◽  
Load Tests ◽  
The Cost

The design of the industrial port of Sepetiba, 50 km south of Rio de Janeiro, Brazil, required a detailed evaluation of the underlying soft soil deposits. Initially, on the basis of laboratory tests, it was proposed to remove approximately 3.7 × 106 m3 of the very soft deposits in the stockpile area by dredging and substitute with hydraulic sand fill. Subsequently, in view of the cost of such a measure, a large program of field investigations was initiated to study the in situ characteristics of the soft clay to evaluate whether replacement of this material and (or) ground improvement was necessary. As part of this investigation, two large identically instrumented test fills (test fills B and D), each 65 m2 in plan and 5 m high, with 3:1 slopes were constructed. Test fill B was constructed over natural ground, whereas the subsoil beneath test fill D was treated with stone columns. The instrumentation for each test fill consisted of piezometers, deep settlement plates, surface settlement plates, and inclinometers. This paper provides a description of the field investigations, observations on installation of stone columns, analysis of instrumentation, a comparison of the behaviour of the two test fills, and a discussion on load tests on individual stone columns. Key words : case history, embankment, ground improvement, instrumentation, soft clay, stone columns.

Sign in / Sign up

Export Citation Format

Share Document