scholarly journals Warm mix asphalt mixture using modified asbuton semi extraction modify and synthetic zeolite additive

2019 ◽  
Vol 276 ◽  
pp. 03003
Author(s):  
Leo Sentosa ◽  
S Subagio Bambang ◽  
Harmein Rahman ◽  
R. Anwar Yamin
Keyword(s):  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Warm Mix Asphalt ◽  
Synthetic Zeolite ◽  
Asphalt Mixtures ◽  
Marshall Test ◽  
Asphalt Modification ◽  
Characteristic Values ◽  
Higher Temperature ◽  
Pavement Construction

Modifying asphalt aims to improve the performance of the asphalt pavement construction as indicated by increased resistance to permanent deformation and fatigue crack. Asbuton Semi Extraction is one of the materials that can be used for asphalt modification. The addition of Asbuton semi-extraction increases the value of Bitumen Stability Modulus, resistance to permanent deformation and can also increase the asphalt PG value, but require a higher temperature for mixing and compaction. The high temperatures for the manufacture of asphalt mixtures require considerable energy at a more expensive cost and will result in large emissions. The asphalt mixing technology currently being developed is Asphalt Warm Mix, that is asphalt mixture with mixing temperature below 1500°C. One method is to use zeolite additives. The asphalt mixture with the addition of synthetic zeolite can be prepared by mixing and compaction temperatures lower than 30°C of the hot mixture. From the Marshall test, it is known that zeolite addition of 0.3% of the total weight of the mixture gives the characteristic values of the asphalt mixture which still meets the requirements of the specification used. Increased zeolite levels minimize the value of mixed resistance to the immersion indicated by the IRS Marshall value.

Rheological Properties of Asphalt Binder Modified with Chemical Warm Asphalt Additive

2013 ◽  
Vol 671-674 ◽  
pp. 1692-1699 ◽  
Author(s):  
Mohd Ezree Abdullah ◽  
Kemas Ahmad Zamhari ◽  
Mustafa Kamal Shamshudin ◽  
Hainin Mohd Rosli ◽  
Mohd Khairul Idham
Keyword(s):  
Energy Consumption ◽  
Rheological Properties ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Mechanical Analysis ◽  
Warm Mix Asphalt ◽  
Dynamic Shear ◽  
Rotational Viscosity ◽  
Pavement Construction

Going towards sustainable pavement construction, asphalt industries constantly give their effort to implement Warm Mix Asphalt (WMA) by adding the chemical warm asphalt additive (CWAA). This can lower its energy consumption and pollution by reducing the mixing and compaction temperatures of the asphalt mixture without affecting its properties. Several studies have been conducted evaluating the properties of the WMA, however, little documented research on the rheology of the binders containing CWAA is available especially when dealing the sources of binders. In this paper, the tests for rheology characteristics of the Malaysian asphalt binder containing CWAA were conducted with rotational viscosity and for dynamic mechanical analysis with dynamic shear rheometer (DSR). The results of the investigation indicated that the CWAA had a significant reduction of required heat for mixing and compaction effort and also shows lower permanent deformation when compared to the control binder.

scholarly journals Performance Evaluation of WMA Containing Re-Refined Acidic Sludge and Amorphous Poly Alpha Olefin (APAO)

2021 ◽  
Vol 13 (6) ◽  
pp. 3315
Author(s):  
Mansour Fakhri ◽  
Danial Arzjani ◽  
Pooyan Ayar ◽  
Maede Mottaghi ◽  
Nima Arzjani
Keyword(s):  
Resilient Modulus ◽  
Permanent Deformation ◽  
Road Construction ◽  
Moisture Damage ◽  
Asphalt Mixtures ◽  
Modified Bitumen ◽  
Alternative Source ◽  
The Road ◽  
Marshall Test ◽  
Alpha Olefin

The use of waste materials has been increasingly conceived as a sustainable alternative to conventional materials in the road construction industry, as concerns have arisen from the uncontrolled exploitation of natural resources in recent years. Re-refined acidic sludge (RAS) obtained from a waste material—acidic sludge—is an alternative source for bitumen. This study’s primary purpose is to evaluate the resistance of warm mix asphalt (WMA) mixtures containing RAS and a polymeric additive against moisture damage and rutting. The modified bitumen studied in this research is a mixture of virgin bitumen 60/70, RAS (10, 20, and 30%), and amorphous poly alpha olefin (APAO) polymer. To this end, Marshall test, moisture susceptibility tests (i.e., tensile strength ratio (TSR), residual Marshall, and Texas boiling water), resilient modulus, and rutting assessment tests (i.e., dynamic creep, Marshall quotient, and Kim) were carried out. The results showed superior values for modified mixtures compared to the control mix considering the Marshall test. Moreover, the probability of a reduction in mixes’ moisture damage was proved by moisture sensitivity tests. The results showed that modified mixtures could improve asphalt mixtures’ permanent deformation resistance and its resilience modulus. Asphalt mixtures containing 20% RAS (substitute for bitumen) showed a better performance in all the experiments among the samples tested.

Determining Optimum Carbon Nanotubes Content for Asphalt Mixture in Road Pavements

2021 ◽  
Vol 1023 ◽  
pp. 121-126
Author(s):  
Van Bach Le ◽  
Van Phuc Le
Keyword(s):  
Carbon Nanotubes ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Construction Cost ◽  
Asphalt Mixtures ◽  
Static Modulus ◽  
Pavement Construction ◽  
Modified Binder ◽  
Marshall Stability

Although small amount of binder in asphalt concrete mixture may commonly range from 3.5 to 5.5% of total mixture as per many international specifications, it has a significant impact on the total cost of pavement construction. Therefore, this paper investigated the effects of five carbon nanotubes contents of 0.05%, 0.1%, 0.15%, 0.2%, 0.25% by asphalt weight as an additive material for binder on performance characteristics of asphalt mixtures. Performance properties of CNTs modified asphalt mixtures were investigated through the Marshall stability (MS) test, indirect tensile (IDT) test, static modulus (SM) test, wheel tracking (WT) test. The results indicated that asphalt mixtures with CNT modified binder can improve both the rutting performance, IDT strength and marshall stability of tested asphalt mixtures significantly at higher percentages of carbon nanotubes. However, the issue that should be considered is the construction cost of asphalt pavement. Based on the asphalt pavement structural analysis and construction cost, it can be concluded that an optimum CNT content of 0.1% by asphalt weight may be used as additive for asphalt binder in asphalt mixtures.

scholarly journals Functional and environmental performance of plant-produced crumb rubber asphalt mixtures using the dry process

2021 ◽  
Vol 54 (5) ◽  
Author(s):  
M. Bueno ◽  
R. Haag ◽  
N. Heeb ◽  
P. Mikhailenko ◽  
L. Boesiger ◽  
...  
Keyword(s):  
Environmental Performance ◽  
High Performance ◽  
Large Scale ◽  
Fatigue Behavior ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Crumb Rubber ◽  
Asphalt Mixtures ◽  
Gaseous Emissions ◽  
Dry Process

AbstractIncorporating crumb rubber (CR) using the dry process, directly in the asphalt mixture rather than into the bituminous binder requires no plant retrofitting, and therefore is the most practical industrial method for CR incorporation into asphalt mixtures. Nevertheless, very few large scale studies have been conducted. This work uses a holistic approach and reports on the functional and environmental performance of asphalt mixtures with different concentrations of CR fabricated employing the dry process in asphalt plants. Gaseous emissions were monitored during the production and laboratory leaching tests simulating the release of pollutants during rain, was conducted to evaluate the toxicology of both the CR material alone and the modified asphalt mixtures. In addition, laboratory compacted samples were tested to assess their fatigue behavior. Furthermore, noise relevant surface properties of large roller compacted slabs were evaluated before and after being subjected to a load simulator (MMLS3) to evaluate their resistance to permanent deformation. The results confirm that comparable performance can be achieved with the incorporation of CR using the dry process for high performance surfaces such as semi-dense asphalt, which usually require the use of polymer modified binders. Environmental performance improvement can be achieved by a washing step of the CR material that could remove polar CR additives which have commonly been used as vulcanization accelerator during rubber production.

scholarly journals The Durability of the AC-BC Mixture Using Stone of Baba Mount, Tana Toraja Regency

2021 ◽  
Vol 3 (3) ◽  
pp. 69-75
Author(s):  
Cindy Pasilaputri ◽  
Alpius ◽  
Louise Elizabeth Radjawane
Keyword(s):  
Immersion Time ◽  
Asphalt Mixture ◽  
Immersion Test ◽  
Test Method ◽  
Traffic Load ◽  
Technical Requirements ◽  
High Durability ◽  
Marshall Test ◽  
Pavement Construction

Several factors that can affect road damage are excessive traffic load, temperature (weather), water, and pavement construction that does not meet the technical requirements. The durability of an asphalt mixture is the resistance of the mixture to the effects of water, water vapor, and temperature. A mixture with a high durability value provides a good mix quality and long-term use. The purpose of this study was to determine the durability of the AC-BC mixture using Mount Baba stone. The general specifications of Bina Marga in 2018 are the reference in this study. By using the standard Marshall test method, the results obtained through the Marshall AC-BC mixture immersion test with a duration of immersion time of 0.5 hours, 12 hours, 24 hours, 36 hours, 48 hours, 60 hours with a durability value of 95.49% - 86.99%. The increase in immersion time causes a decrease in the durability of the mixture.

scholarly journals Viscoelastic Parameters of Asphalt Mixtures Identified in Static and Dynamic Tests

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2084 ◽  
Author(s):  
Piotr Mackiewicz ◽  
Antoni Szydło
Keyword(s):  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Dynamic Test ◽  
Asphalt Mixtures ◽  
Rheological Parameters ◽  
Dynamic Tests ◽  
Static Test ◽  
Viscoelastic Parameters ◽  
Static Creep ◽  
Asphalt Content

We present two methods used in the identification of viscoelastic parameters of asphalt mixtures used in pavements. The static creep test and the dynamic test, with a frequency of 10 Hz, were carried out based on the four-point bending beam (4BP). In the method identifying viscoelastic parameters for the Brugers’ model, we included the course of a creeping curve (for static creep) and fatigue hysteresis (for dynamic test). It was shown that these parameters depend significantly on the load time, method used, and temperature and asphalt content. A similar variation of parameters depending on temperature was found for the two tests, but different absolute values were obtained. Additionally, the share of viscous deformations in relation to total deformations is presented, on the basis of back calculations and finite element methods. We obtained a significant contribution of viscous deformations (about 93% for the static test and 25% for the dynamic test) for the temperature 25 °C. The received rheological parameters from both methods appeared to be sensitive to a change in asphalt content, which means that these methods can be used to design an optimal asphalt mixture composition—e.g., due to the permanent deformation of pavement. We also found that the parameters should be determined using the creep curve for the static analyses with persistent load, whereas in the case of the dynamic studies, the hysteresis is more appropriate. The 4BP static creep and dynamic tests are sufficient methods for determining the rheological parameters for materials designed for flexible pavements. In the 4BP dynamic test, we determined relationships between damping and viscosity coefficients, showing material variability depending on the test temperature.

Superpave Models: Predicting Performance during Design and Construction

1996 ◽  
Vol 1545 (1) ◽  
pp. 105-112
Author(s):  
Gerald A. Huber ◽  
Xishun Zhang ◽  
Robin Fontaine
Keyword(s):  
Prediction Models ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Engineering Properties ◽  
Design System ◽  
Widespread Application ◽  
Premature Failure ◽  
The Impact

The Strategic Highway Research Program (SHRP) spent $50 million researching asphalt binders and asphalt mixtures and provided three main products: an asphalt binder specification, an asphalt mixture specification, and Superpave, an asphalt mixture design system that encompasses both the binder and mixture specification. SHRP researchers have provided tools that promise more robust asphalt mixtures with reduced risk of premature failure. Implementation of the specifications and mix design system will require overcoming several obstacles. Superpave must be demonstrated to be practical and easy to use. The impact of Superpave aggregate requirements on aggregate availability must be determined. The Superpave gyratory compaction procedure has been uniquely defined and then calibrated to traffic volume. The reasonableness of this approach must be tested in widespread application. Perhaps the largest implementation hurdle exists in the performance models. Expensive test equipment is necessary to do the performance-based tests. The performance predictions must be established as reasonable to justify the cost. A highway reconstruction project containing three Superpave Level 1 mix designs is documented including quality control done with the Superpave gyratory compactor. Superpave Level 2 performance-based tests were carried out to predict permanent deformation of the design and the mixture as constructed. The performance-based engineering properties obtained from the tests are evaluated, and the reasonableness of the performance prediction models is discussed.

scholarly journals Performance Evaluation of Warm- and Hot-Mix Asphalt Mixtures Based on Laboratory and Accelerated Pavement Tests

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
Yongjoo Kim ◽  
Jaejun Lee ◽  
Cheolmin Baek ◽  
Sunglin Yang ◽  
Sooahn Kwon ◽  
...  
Keyword(s):  
Asphalt Mixture ◽  
Warm Mix Asphalt ◽  
Strength Test ◽  
Asphalt Mixtures ◽  
Limited Data ◽  
Tensile Strength Test ◽  
Paving Asphalt ◽  
Dynamic Modulus Test ◽  
Indirect Tensile ◽  
Lower Temperature

A number of warm-mix asphalt (WMA) technologies are used to reduce the temperature at which the asphalt mixtures are produced and compacted, apparently without compromising the performance of the pavement. The main objective of this study is to determine whether the use of an innovative wax-based LEADCAP WMA additive influences the performance of the asphalt mixture, which is produced and compacted at significantly low temperatures. The WMA pavement using LEADCAP additive (WMA-LEADCAP) along with a control HMA pavement was evaluated with respect to their performances of rutting resistance, crack resistance, and viscoelastic property based on the laboratory dynamic modulus test, indirect tensile strength test, and in-door accelerated pavement test (APT) results. With the limited data carried out, the LEADCAP additive is effective in producing and paving asphalt mixture at approximately 30°C lower temperature than a control HMA mixture, and the performances of WMA-LEADCAP pavement are comparable to a control HMA pavement.

Experimental Study on Overlay Asphalt Mixture

2012 ◽  
Vol 253-255 ◽  
pp. 607-610
Author(s):  
Yu Qing Yuan ◽  
Wei Li ◽  
Xue Chan Li ◽  
Tao Guo
Keyword(s):  
High Temperature ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Immersion Test ◽  
High Temperature Stability ◽  
Freeze Thaw ◽  
Passing Rate ◽  
Splitting Test ◽  
Marshall Test ◽  
Higher Temperature

To study the asphalt pavement performances on high temperature or its water stabilities, a series of tests, including high temperature stability test, immersion Marshall test, freeze-thaw splitting test, were finished. According to bailey method, initial quasi grading were calculated. Passing rate of 2.36 mm is respectively 36.3%, 33.1%, 36.1%, 38.7%, which is close to the initial quasi grading, namely 36%, 31.5%, 36%, 40%. Respectively at the test temperature of 60 °C, 68 °C, rutting tests were put forward. The results show that the mixture of gradation one has a higher temperature stability than the others in any case. Marshall immersion test and freeze-thaw test were conducted, optimizing with freeze-thaw splitting intensity ratio, which shows that the mixture of gradation one has a better water stability. To sum up, gradation one is recommended, designed by Marshall compaction molding with times of 100.

Research on Application of Warm Mix Asphalt Technology in Hot In-Place Recycled Engineering

2013 ◽  
Vol 361-363 ◽  
pp. 1655-1658
Author(s):  
Xiao Li Li ◽  
Qing Zhou Wang ◽  
Shu Yan Liu
Keyword(s):  
Asphalt Mixture ◽  
Temperature Stability ◽  
Warm Mix Asphalt ◽  
Pavement Performance ◽  
High Temperature Stability ◽  
Recycled Asphalt ◽  
Marshall Test ◽  
Recycling Technology ◽  
Research On Application

Because of the heating limitation of old pavement and the restriction of climate, the quality of hot in-place recycled pavement was different to control. The warm m,ix asphalt technology was introduced to improve the heterogeneity and compactness of the hot in-place recycled pavement and decrease its construction temperature. The compaction characteristics of warm in-place recycled asphalt mixture were analyzed and its molding temperature was determined through the Marshall test. The pavement performance of warm in-place recycled asphalt mixture was analyzed whose results indicated that the introduction of warm mix asphalt technology was able to improve the compactness, the high temperature stability and water stability of hot in-place recycled asphalt mixture and reduce the influence of environment over its construction quality. A warm in-place recycled engineering of Shian expressway was introduced to verify the feasibility of warm in-place recycling technology which demonstrated that the warm in-place recycling technology was able to improve the heterogeneity and compaction quality of the recycled pavement and weaken the environmental pollution.

Sign in / Sign up

Export Citation Format

Share Document