scholarly journals Effects of bushing profiles on the elastohydrodynamic lubrication performance of the journal bearing under steady operating conditions

2019 ◽  
Vol 20 (2) ◽  
pp. 207 ◽  
Author(s):  
Chongpei Liu ◽  
Bin Zhao ◽  
Wanyou Li ◽  
Xiqun Lu
Keyword(s):  
Journal Bearing ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Asperity Contact ◽  
Parabolic Profile ◽  
Leakage Flow Rate ◽  
Lubrication Performance ◽  
Load Carrying ◽  
Edge Wear ◽  
Flow Rate Change

The bushing profiles have important effects on the performance of journal bearing. In this article, the effects of plain profile, double conical profile, and double parabolic profile on the elastohydrodynamic lubrication of the journal bearing under steady operating conditions are investigated. The journal misalignment and asperity contact between journal and bushing surface are considered, while the modification of the bushing profiles due to running-in is neglected. Finite element method is used for the elastic deformation of bushing surface, while the numerical solution is established by using finite difference method and overrelaxation iterative method. The numerical results reveal that the double parabolic profile with appropriate size can significantly increase the minimum film thickness and reduce the asperity contact pressure and friction, while the maximum film pressure, load-carrying capacity, and leakage flow rate change slightly under steady operating conditions. This study may help to reduce the edge wear and prolong the service life of the journal bearing.

Effects of double parabolic profiles with groove textures on the hydrodynamic lubrication performance of journal bearing under steady operating conditions

2020 ◽  
Vol 21 (3) ◽  
pp. 301
Author(s):  
Chongpei Liu ◽  
Wanyou Li ◽  
Xiqun Lu ◽  
Bin Zhao
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Operating Conditions ◽  
Lubricating Oil ◽  
Asperity Contact ◽  
Adiabatic Flow ◽  
Lubrication Performance ◽  
Load Carrying ◽  
Edge Wear ◽  
Journal Misalignment

The textures on the bushing surface have important effects on the performance of journal bearing. In this study, the effects of double parabolic profiles with groove textures on the hydrodynamic lubrication performance of journal bearing under steady operating conditions are investigated theoretically. The journal misalignment, asperity contact and thermal effects are considered, while the profile modifications due to running-in are neglected. The Winkler/Column model is used to calculate the elastic deformation of bushing surface and the adiabatic flow hypothesis is adopted to obtain the effective temperature of lubricating oil. The numerical solution is established by using finite difference and overrelaxation iterative methods, and the rupture zone of oil film is determined by Reynolds boundary conditions. The numerical results reveal that the double parabolic profiles with groove textures with proper location and geometric sizes can increase load carrying capacity and reduce friction loss under steady operating conditions, which effectively overcome the drawbacks of double parabolic profiles. This novel bushing profile may help to reduce the bushing edge wear and enhance the lubrication performance of journal bearing.

A Starved Mixed Elastohydrodynamic Lubrication Model for the Prediction of Lubrication Performance, Friction and Flash Temperature With Arbitrary Entrainment Angle

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Wei Pu ◽  
Dong Zhu ◽  
Jiaxu Wang
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Flash Temperature ◽  
Machined Surface ◽  
Lubrication Performance ◽  
Wide Range ◽  
Starved Lubrication

In this study, a modified mixed lubrication model is developed with consideration of machined surface roughness, arbitrary entraining velocity angle, starvation, and cavitation. Model validation is executed by means of comparison between the obtained numerical results and the available starved elastohydrodynamic lubrication (EHL) data found from some previous studies. A comprehensive analysis for the effect of inlet oil supply condition on starvation and cavitation, mixed EHL characteristics, friction and flash temperature in elliptical contacts is conducted in a wide range of operating conditions. In addition, the influence of roughness orientation on film thickness and friction is discussed under different starved lubrication conditions. Obtained results reveal that inlet starvation leads to an obvious reduction of average film thickness and an increase in interasperity cavitation area due to surface roughness, which results in significant increment of asperity contacts, friction, and flash temperature. Besides, the effect of entrainment angle on film thickness will be weakened if the two surfaces operate under starved lubrication condition. Furthermore, the results show that the transverse roughness may yield thicker EHL films and lower friction than the isotropic and longitudinal if starvation is taken into account. Therefore, the starved mixed EHL model can be considered as a useful engineering tool for industrial applications.

Thermo-hydrodynamic simulation study of twin-groove elliptical (two-lobe) journal bearing of steam turbine with experimental investigations

2020 ◽  
pp. 135065012097379
Author(s):  
Navin Kumar ◽  
Akash Shukla ◽  
Sanjay Bansal ◽  
Chandra B Khatri ◽  
Gannath D Thakre ◽  
...  
Keyword(s):  
Journal Bearing ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Inlet Temperature ◽  
Steam Turbines ◽  
Hydrodynamic Simulation ◽  
Load Carrying ◽  
Temperature Load ◽  
Fully Automatic ◽  
Hydrodynamic Journal Bearing

The present paper reports an experimental and theoretical investigation on performance behaviour of twin-groove elliptical (two-lobe) white metal hydrodynamic journal bearing used in steam turbines. The experiments are performed on a fully automatic journal bearing test rig with provisions to various operating conditions (i.e. load, speed, and lubricant temperature). The performance behaviour in terms of coefficient of friction, lubricant inlet temperature, load carrying capacity, journal displacement, weight loss etc. has been presented. In addition to this, numerical investigations have also been performed with the numerical solution of governing Reynolds equation using FEM (finite element method) technique and Jakobsson-Floberg-Olsson (JFO) boundary condition. The experimentally obtained and theoretical results have been correlated.

Mixed Elastohydrodynamic Lubrication With Three-Dimensional Machined Roughness in Spiral Bevel and Hypoid Gears

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Wei Pu ◽  
Jiaxu Wang ◽  
Rongsong Yang ◽  
Dong Zhu
Keyword(s):  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Strength Prediction ◽  
Flash Temperature ◽  
Hypoid Gears ◽  
Lubrication Performance ◽  
Lubrication Condition ◽  
Spiral Bevel ◽  
Film Lubrication

Spiral bevel and hypoid gears are key components widely used for transmitting significant power in various types of vehicles and engineering machineries. In reality, these gear surfaces are quite rough with three-dimensional (3D) topography that may significantly influence the lubrication formation and breakdown as well as components failures. Previous spiral bevel and hypoid gears lubrication studies, however, were limited mostly to cases under the full-film lubrication condition with smooth surfaces. In the present study, a comprehensive analysis for gearing geometry, kinematics, mixed lubrication performance, and friction and interfacial flash temperature in spiral bevel and hypoid gears is developed based on a recently developed mixed elastohydrodynamic lubrication (EHL) model that is capable of handling practical cases with 3D machined roughness under severe operating conditions and considering the effect of arbitrary entrainment angle. Obtained results from sample cases show that the simulation model developed can be used as an engineering tool for spiral bevel and hypoid gears design optimization and strength prediction.

A Mixed-TEHD Model for Journal-Bearing Conformal Contact—Part II: Contact, Film Thickness, and Performance Analyses

1998 ◽  
Vol 120 (2) ◽  
pp. 206-213 ◽  
Author(s):  
Qian (Jane) Wang ◽  
Fanghui Shi ◽  
Si C. Lee
Keyword(s):  
Journal Bearing ◽  
Thermal Conditions ◽  
Journal Bearings ◽  
Mixed Lubrication ◽  
Operating Conditions ◽  
Contact Theory ◽  
Asperity Contact ◽  
High Eccentricity ◽  
And Performance ◽  
Contact Part

Investigation of the mixed lubrication of journal-bearing conformal contacts is very important for failure prevention and design improvement. This paper studies the asperity contact in heavily loaded journal bearings with Lee and Ren’s asperity contact theory in a newly developed mixed-TEHD (Thermal Elasto-Hydro-Dynamic) model and analyzes the performance of simulated journal bearings under high eccentricity ratios. The effects of operating conditions, bearing structures, and thermal conditions on the contact severity were numerically investigated. The results indicate that the asperity contact pressure and the performance of journal bearings in the mixed lubrication are strongly affected by the geometric design and the thermal-elastic deformations. The heat transfer of the bearing-lubricant-journal system was also shown to play a role.

Design and Development of Permanent Magneto-Hydrodynamic Hybrid Journal Bearing

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
K. P. Lijesh ◽  
Harish Hirani
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Magnetic Bearing ◽  
Operating Conditions ◽  
Fluid Film ◽  
Test Setup ◽  
Fluid Film Bearings ◽  
Lubrication Regime ◽  
Load Carrying ◽  
Hybrid Bearing

Fluid film bearings (FFBs) provide economic wear-free performance when operating in hydrodynamic lubrication regime. In all other operating conditions, except hydrostatic regime, these bearings are subjected to wear. To get wear-free performance even in those conditions, a hybrid (hydrodynamic + rotation magnetized direction (RMD) configured magnetic) bearing has been proposed. The hybrid bearing consists of square magnets to repel the shaft away from the bearing bore. Load-carrying capacities of four configurations of hybrid bearings were determined. The results are presented in this paper. The best configuration of hybrid bearing was developed. A test setup was developed to perform the experiments on the fluid film and hybrid bearings. The wear results of both the bearings under same operating conditions are presented.

Mass Conserving Elastohydrodynamic Piston Lubrication Model With Incorporated Crown Lands

2007 ◽  
Author(s):  
Mustafa Duyar
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Cylinder Liner ◽  
Thermodynamic Cycle ◽  
Operating Conditions ◽  
Asperity Contact ◽  
Piston Skirt ◽  
Piston Crown ◽  
Parametric Studies ◽  
Volume Method ◽  
Crown Lands

This paper describes a comprehensive model of Elastohydrodynamic piston lubrication, incorporated the crown lands into solution domain to characterize the effect of crown-liner interactions on piston motion. Elastohydrodynamic Lubrication (EHL) analysis of a piston skirt-liner conjunction is in general a useful methodology for design analysis of pistons. The diameters of piston crown lands are much less than those of skirt and liner for typical piston designs. Therefore crown lands normally do not interact with liner under usual operating conditions and hence most of the researchers exclude crown lands from the EHL analysis and mainly focus on piston skirt. However, under some of the engine operating conditions piston crown lands play important role in the secondary dynamics and tribology aspects of pistons. During the thermodynamic cycle when piston is hot and cylinder liner is relatively colder, piston thermal expansion leads to crown-liner interaction, which necessitates EHL, asperity contact and wear considerations of piston crown along with piston skirt. The simulation methodology for piston EHL analysis uses a mass-conserving algorithm for the finite volume method solution of Reynolds equation, which is coupled to elasticity relations and Greenwood-Tripp asperity contact model. Elrod’s mass conserving algorithm enables to model and analyze partially lubricated piston-liner interface by the input of oil supply and moreover rigorously handles cavitated zones, and takes into account piston ring grooves, piston cut-outs and unlubricated areas due to piston geometry. Results are presented from parametric studies that show comparisons between the analyses of the models with piston skirt lubrication only and piston lubrication, which incorporates the crown lands to the EHL domain.

Investigation of the Failure of Heavily Loaded Journal Bearings

1994 ◽  
Vol 208 (3) ◽  
pp. 167-171
Author(s):  
D Ashman
Keyword(s):  
Film Thickness ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Elastohydrodynamic Lubrication ◽  
Failure Criteria ◽  
Operating Conditions ◽  
Minimum Film Thickness ◽  
Hydrodynamic Solution ◽  
Metrological Study ◽  
Theoretical Minimum

This paper gives details of a combined theoretical and experimental investigation of a plain journal bearing under heavily loaded conditions together with a metrological study of the bearing geometry. It was found that under high loading conditions a simplified analytical expression relating the Sommerfeld number to the non-dimensional minimum film thickness, using a hydrodynamic solution of the isoviscous form of the Reynolds equation, could be developed. An alternative theoretical solution based on elastohydrodynamic lubrication was also considered. In addition, experimental work determined a variety of operating conditions that produced metal-to-metal contact. These operating conditions were then compared with the theoretical minimum film thickness calculations and bearing manufacturing data. This process was used to determine combined failure criteria based on operating conditions and machining capability.

Tilting-Pad Journal Bearing in Hybrid Operation: A Numerical and Experimental Investigation

2018 ◽  
Author(s):  
Nico Buchhorn ◽  
Sebastian Kukla ◽  
Beate Bender ◽  
Marc Neumann
Keyword(s):  
Hydrostatic Pressure ◽  
Carrying Capacity ◽  
Journal Bearing ◽  
Operating Conditions ◽  
Load Carrying Capacity ◽  
Oil Supply ◽  
Hybrid Operation ◽  
Tilting Pad ◽  
Load Carrying ◽  
Tilting Pad Journal Bearing

Large turbine bearings are usually equipped with hydrostatic jacking mechanisms to separate bearing and shaft during transient start-stop procedures. They are turned off once hydrodynamic operation is reached. In some cases, under severe operating conditions, the hydrostatic oil supply is kept running although the rotor already runs in full speed. The supplied amount of jacking oil is very small compared to the regular oil supply. However, experimental data of a large tilting-pad bearing shows that this hybrid operation has a considerable impact on the load carrying capacity in terms of lower pad temperature and larger film thickness. In this paper, a theoretical investigation to analyse the effect of increased load carrying capacity of a large tilting-pad journal bearing in hybrid operation is presented. The increase is driven by three different aspects: 1) hydrostatic pressure component, 2) increase in lubricant viscosity due to the injection of cold oil, 3) decrease of temperature gradients and thus thermal pad deformation. Subject of the approach is a ø500 mm five-pad, rocker-pivot tilting-pad journal bearing in flooded lubrication mode. The experiments are carried out on the Bochum test rig for large turbine bearings. The theoretical analyses are performed with a simulation code solving the Reynolds and energy equations for the oil film and calculating the thermomechanical pad deformations simultaneously. By considering each of the three above aspects separately and in combination, their share of load increase can be assessed individually. Contrary to expectations, the results indicate that the increase is not mostly based on the hydrostatic pressure component. Instead, the advantageously decreased pad deformations make the largest contribution to the increased load carrying capacity while the alteration in viscosity shows the least impact.

Thermohydrodynamic Lubrication Analysis of Misaligned Plain Journal Bearing With Rough Surface

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Jun Sun ◽  
Mei Deng ◽  
Yonghong Fu ◽  
Changlin Gui
Keyword(s):  
Surface Roughness ◽  
Thermal Effect ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Eccentricity Ratio ◽  
Oil Viscosity ◽  
Oil Film ◽  
Lubrication Performance ◽  
Journal Misalignment

Journal misalignment exists generally in journal bearings. When severe journal misalignment takes place, the minimum film thickness of journal bearings reduces greatly. In this condition, the surface roughness, the oil viscosity-pressure relationship (VPR), and the thermal effect have obvious effects on hydrodynamic lubrication performance of misaligned bearings. In this paper, the oil film pressure, oil film temperature, load-carrying capacity, end leakage flow rate, frictional coefficient, and misalignment moment of a journal bearing with different angles of journal misalignment and surface roughness, and considering oil VPR and thermal effect, were calculated based on the generalized Reynolds equation, energy equation, and solid heat conduction equation. The results show that the oil VPR and surface roughness have a significant effect on the lubrication of misaligned journal bearings under large eccentricity ratio. The thermal effect will affect obviously the lubrication of misaligned journal bearings when eccentricity ratio and angle of journal misalignment are all large. In the present design, the size of the journal bearing is compact more and more, and the eccentricity ratio and angle of journal misalignment are usually large in operating conditions. Therefore, it is necessary to take the effects of journal misalignment, surface roughness, oil VPR, and thermal effect into account in the design and analyses of journal bearings.

Sign in / Sign up

Export Citation Format

Share Document