Design and Development of Permanent Magneto-Hydrodynamic Hybrid Journal Bearing

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
K. P. Lijesh ◽  
Harish Hirani
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Magnetic Bearing ◽  
Operating Conditions ◽  
Fluid Film ◽  
Test Setup ◽  
Fluid Film Bearings ◽  
Lubrication Regime ◽  
Load Carrying ◽  
Hybrid Bearing

Fluid film bearings (FFBs) provide economic wear-free performance when operating in hydrodynamic lubrication regime. In all other operating conditions, except hydrostatic regime, these bearings are subjected to wear. To get wear-free performance even in those conditions, a hybrid (hydrodynamic + rotation magnetized direction (RMD) configured magnetic) bearing has been proposed. The hybrid bearing consists of square magnets to repel the shaft away from the bearing bore. Load-carrying capacities of four configurations of hybrid bearings were determined. The results are presented in this paper. The best configuration of hybrid bearing was developed. A test setup was developed to perform the experiments on the fluid film and hybrid bearings. The wear results of both the bearings under same operating conditions are presented.

Effects of double parabolic profiles with groove textures on the hydrodynamic lubrication performance of journal bearing under steady operating conditions

2020 ◽  
Vol 21 (3) ◽  
pp. 301
Author(s):  
Chongpei Liu ◽  
Wanyou Li ◽  
Xiqun Lu ◽  
Bin Zhao
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Operating Conditions ◽  
Lubricating Oil ◽  
Asperity Contact ◽  
Adiabatic Flow ◽  
Lubrication Performance ◽  
Load Carrying ◽  
Edge Wear ◽  
Journal Misalignment

The textures on the bushing surface have important effects on the performance of journal bearing. In this study, the effects of double parabolic profiles with groove textures on the hydrodynamic lubrication performance of journal bearing under steady operating conditions are investigated theoretically. The journal misalignment, asperity contact and thermal effects are considered, while the profile modifications due to running-in are neglected. The Winkler/Column model is used to calculate the elastic deformation of bushing surface and the adiabatic flow hypothesis is adopted to obtain the effective temperature of lubricating oil. The numerical solution is established by using finite difference and overrelaxation iterative methods, and the rupture zone of oil film is determined by Reynolds boundary conditions. The numerical results reveal that the double parabolic profiles with groove textures with proper location and geometric sizes can increase load carrying capacity and reduce friction loss under steady operating conditions, which effectively overcome the drawbacks of double parabolic profiles. This novel bushing profile may help to reduce the bushing edge wear and enhance the lubrication performance of journal bearing.

Influence of Surface Roughness on Non-Newtonian Thermohydrostatic Performance of a Hole-Entry Hybrid Journal Bearing

2007 ◽  
Vol 129 (3) ◽  
pp. 595-602 ◽  
Author(s):  
T. Nagaraju ◽  
Satish C. Sharma ◽  
S. C. Jain
Keyword(s):  
Surface Roughness ◽  
Thermal Effect ◽  
Carrying Capacity ◽  
Journal Bearing ◽  
Fluid Film ◽  
Load Carrying Capacity ◽  
Fluid Film Bearings ◽  
Load Carrying ◽  
Transverse Pattern ◽  
Newtonian Behavior

A general solution scheme to account the surface roughness and the cross-film viscosity variation of lubricant due to its non-Newtonian behavior and rise in fluid-film temperature for the analysis of fluid-film bearings is presented. The combined influence of surface roughness, non-Newtonian behavior of lubricant, and thermal effects on the performance of a hole-entry hybrid journal bearing system has been investigated. The surface roughness, especially stationary roughness (i.e., rough bearing and smooth journal) with a transverse pattern was found to partially compensate for the loss in load-carrying capacity due to the thermal and/or non-Newtonian behavior of lubricant effects. It limits 18.86% loss in load-carrying capacity due to the thermal effect to only 1.6% and 33.99% loss due to the combined influence of non-Newtonian lubricant and thermal effect to 16.76%.

Numerical optimization of surface texture for improved tribological performance of journal bearing at varying operating conditions

2018 ◽  
Vol 70 (9) ◽  
pp. 1608-1618 ◽  
Author(s):  
Ali Usman ◽  
Cheol Woo Park
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Surface Texturing ◽  
Tribological Performance ◽  
Operating Conditions ◽  
Content Type ◽  
Load Carrying ◽  
Recent Developments ◽  
Effect Of Surface ◽  
Generalized Reynolds Equation

Purpose Journal bearings are used in numerous rotary machines. The load carrying capacity and friction of a bearing have been major concerns in design. Recent developments in surface texturing have showed potential outcomes to improve the tribological characteristics of mating surfaces. This study aims to investigate surface textures, which are transverse to the sliding direction, for frictional response of the journal bearing. Design/methodology/approach A hydrodynamic lubrication model is considered to evaluate the effect of surface texturing on the performance of a journal bearing at varying operating conditions. The two-dimensional generalized Reynolds equation, coupled with mass-conserving Elrod cavitation algorithm, is solved to evaluate texture-induced variations in tribological performance parameters. Findings Results have showed remarkable improvements in frictional response. Moreover, micro-textures on the journal surface alter the cavitation response and film-reformation in the hydrodynamic conjunction of the plain bearing. Originality/value Operating condition-based comprehensive exhaustive optimization of texture geometry is performed to generate widespread conclusion.

scholarly journals Improvement of Tilting-Pad Journal Bearing Operating Characteristics by Application of Eddy Grooves

Lubricants ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 18
Author(s):  
Eckhard Schüler ◽  
Olaf Berner
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Load Capacity ◽  
Fluid Film ◽  
Operating Characteristics ◽  
Fluid Film Bearings ◽  
Tilting Pad ◽  
Bearing Load ◽  
Bearing Loads ◽  
Tilting Pad Journal Bearing

In high speed, high load fluid-film bearings, the laminar-turbulent flow transition can lead to a considerable reduction of the maximum bearing temperatures, due to a homogenization of the fluid-film temperature in radial direction. Since this phenomenon only occurs significantly in large bearings or at very high sliding speeds, means to achieve the effect at lower speeds have been investigated in the past. This paper shows an experimental investigation of this effect and how it can be used for smaller bearings by optimized eddy grooves, machined into the bearing surface. The investigations were carried out on a Miba journal bearing test rig with Ø120 mm shaft diameter at speeds between 50 m/s–110 m/s and at specific bearing loads up to 4.0 MPa. To investigate the potential of this technology, additional temperature probes were installed at the crucial position directly in the sliding surface of an up-to-date tilting pad journal bearing. The results show that the achieved surface temperature reduction with the optimized eddy grooves is significant and represents a considerable enhancement of bearing load capacity. This increase in performance opens new options for the design of bearings and related turbomachinery applications.

Heat Transfer and Thermal Elastic Deformation Analysis on the Piston/Cylinder Interface of Axial Piston Machines

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Matteo Pelosi ◽  
Monika Ivantysynova
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Elastic Deformation ◽  
Hydrodynamic Lubrication ◽  
Operating Conditions ◽  
Fluid Film ◽  
Design Elements ◽  
Piston Cylinder ◽  
Viscous Shear ◽  
Axial Piston

The piston/cylinder interface of swash plate–type axial piston machines represents one of the most critical design elements for this type of pump and motor. Oscillating pressures and inertia forces acting on the piston lead to its micro-motion, which generates an oscillating fluid film with a dynamically changing pressure distribution. Operating under oscillating high load conditions, the fluid film between the piston and cylinder has simultaneously to bear the external load and to seal the high pressure regions of the machine. The fluid film interface physical behavior is characterized by an elasto-hydrodynamic lubrication regime. Additionally, the piston reciprocating motion causes fluid film viscous shear, which contributes to a significant heat generation. Therefore, to fully comprehend the piston/cylinder interface fluid film behavior, the influences of heat transfer to the solid boundaries and the consequent solid boundaries’ thermal elastic deformation cannot be neglected. In fact, the mechanical bodies’ complex temperature distribution represents the boundary for nonisothermal fluid film flow calculations. Furthermore, the solids-induced thermal elastic deformation directly affects the fluid film thickness. To analyze the piston/cylinder interface behavior, considering the fluid-structure interaction and thermal problems, the authors developed a fully coupled simulation model. The algorithm couples different numerical domains and techniques to consider all the described physical phenomena. In this paper, the authors present in detail the computational approach implemented to study the heat transfer and thermal elastic deformation phenomena. Simulation results for the piston/cylinder interface of an existing hydrostatic unit are discussed, considering different operating conditions and focusing on the influence of the thermal aspect. Model validation is provided, comparing fluid film boundary temperature distribution predictions with measurements taken on a special test bench.

Performance of Stern Tube Bearings under Different Lubrication and Operating Conditions

2009 ◽  
Author(s):  
Jan H. Andersen ◽  
Hiroyuki Sada ◽  
Seiji Yamajo
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Water Soluble ◽  
Analysis Tool ◽  
Test Rig ◽  
Experimental Performance ◽  
Shaft Alignment ◽  
Alignment Analysis

This paper presents the results of an investigation into the theoretical and experimental performance of oil lubricated journal bearings. DNV has developed a new calculation tool for the analysis of journal bearing performance as part of shaft alignment analysis. The results of the calculation tool have been compared to other research and analysis methods under static and dynamic conditions. In addition, white metal bearings were tested with decreasing Sommerfeld number until loss of hydrodynamic lubrication. The experiments were carried out in a bearing test rig and with three different lubricants, normal mineral oil, emulsifying oil, and water-soluble oil. The tests were done with increasing water content in the lubricant. Results from the test were compared with calculation using the DNV analysis tool.

Magneto-rheological fluid slot-entry journal bearing considering thermal effects

2019 ◽  
Vol 30 (18-19) ◽  
pp. 2831-2852 ◽  
Author(s):  
Krishnkant Sahu ◽  
Satish C Sharma
Keyword(s):  
Thermal Effects ◽  
Journal Bearing ◽  
Fluid Model ◽  
Viscous Friction ◽  
Fluid Film ◽  
Applied Current ◽  
Bingham Model ◽  
Geometric Imperfection ◽  
Fluid Film Bearings ◽  
Magneto Rheological

In recent times, controlling the performance of fluid film bearings smartly has become an important area for the fluid film bearing designers. This study deals with the numerical simulation of a magneto-rheological fluid–lubricated two-lobe hybrid slot-entry journal bearing. To make the operating condition more exact and realistic, the influence of geometric imperfection of the journal arising from manufacturing inaccuracies and thermal effect has been considered. Dave magneto-rheological fluid model, a constitutive relation of the Bingham model, and finite element method have been used in this article to simulate the behavior of the magneto-rheological fluid in a slot-entry bearing. The results indicate that the heat generated because of viscous friction rises the temperature of the magneto-rheological fluid, which changes the bearing performance significantly. Considering barrel-shaped journal and magneto-rheological fluid (applied current, Ic = 4 A), the performance of two-lobe slot-entry bearing is superior in terms of the value of [Formula: see text] approximately by a magnitude of 2%, 41%, 181%, 168%, 75%, and 41%, respectively, as compared to that of the base bearing (smooth [Formula: see text], two-lobe bearing, operating with a Newtonian fluid, Ic = 0 A).

scholarly journals Effects of bushing profiles on the elastohydrodynamic lubrication performance of the journal bearing under steady operating conditions

2019 ◽  
Vol 20 (2) ◽  
pp. 207 ◽  
Author(s):  
Chongpei Liu ◽  
Bin Zhao ◽  
Wanyou Li ◽  
Xiqun Lu
Keyword(s):  
Journal Bearing ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Asperity Contact ◽  
Parabolic Profile ◽  
Leakage Flow Rate ◽  
Lubrication Performance ◽  
Load Carrying ◽  
Edge Wear ◽  
Flow Rate Change

The bushing profiles have important effects on the performance of journal bearing. In this article, the effects of plain profile, double conical profile, and double parabolic profile on the elastohydrodynamic lubrication of the journal bearing under steady operating conditions are investigated. The journal misalignment and asperity contact between journal and bushing surface are considered, while the modification of the bushing profiles due to running-in is neglected. Finite element method is used for the elastic deformation of bushing surface, while the numerical solution is established by using finite difference method and overrelaxation iterative method. The numerical results reveal that the double parabolic profile with appropriate size can significantly increase the minimum film thickness and reduce the asperity contact pressure and friction, while the maximum film pressure, load-carrying capacity, and leakage flow rate change slightly under steady operating conditions. This study may help to reduce the edge wear and prolong the service life of the journal bearing.

The Granular Lubricated Journal Bearing: Evidence of Lift Formation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Venkata K. Jasti ◽  
Martin C. Marinack ◽  
Deepak Patil ◽  
C. Fred Higgs
Keyword(s):  
Carrying Capacity ◽  
Granular Flow ◽  
High Speed ◽  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Flow Behavior ◽  
Extreme Environments ◽  
Granular Flows ◽  
Load Carrying Capacity ◽  
Load Carrying

This work demonstrates that granular flows (i.e., macroscale, noncohesive spheres) entrained into an eccentrically converging gap can indeed actually exhibit lubrication behavior as prior models postulated. The physics of hydrodynamic lubrication is quite well understood and liquid lubricants perform well for conventional applications. Unfortunately, in certain cases such as high-speed and high-temperature environments, liquid lubricants break down making it impossible to establish a stable liquid film. Therefore, it has been previously proposed that granular media in sliding convergent interfaces can generate load carrying capacity, and thus, granular flow lubrication. It is a possible alternative lubrication mechanism that researchers have been exploring for extreme environments, or wheel-regolith traction, or for elucidating the spreadability of additive manufacturing materials. While the load carrying capacity of granular flows has been previously demonstrated, this work attempts to more directly uncover the hydrodynamic-like granular flow behavior in an experimental journal bearing configuration. An enlarged granular lubricated journal bearing (GLJB) setup has been developed and demonstrated. The setup was made transparent in order to visualize and video capture the granular collision activity at high resolution. In addition, a computational image processing program has been developed to process the resulting images and to noninvasively track the “lift” generated by granular flow during the journal bearing operation. The results of the lift caused by granular flow as a function of journal rotation rate are presented as well.

Thermo-hydrodynamic simulation study of twin-groove elliptical (two-lobe) journal bearing of steam turbine with experimental investigations

2020 ◽  
pp. 135065012097379
Author(s):  
Navin Kumar ◽  
Akash Shukla ◽  
Sanjay Bansal ◽  
Chandra B Khatri ◽  
Gannath D Thakre ◽  
...  
Keyword(s):  
Journal Bearing ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Inlet Temperature ◽  
Steam Turbines ◽  
Hydrodynamic Simulation ◽  
Load Carrying ◽  
Temperature Load ◽  
Fully Automatic ◽  
Hydrodynamic Journal Bearing

The present paper reports an experimental and theoretical investigation on performance behaviour of twin-groove elliptical (two-lobe) white metal hydrodynamic journal bearing used in steam turbines. The experiments are performed on a fully automatic journal bearing test rig with provisions to various operating conditions (i.e. load, speed, and lubricant temperature). The performance behaviour in terms of coefficient of friction, lubricant inlet temperature, load carrying capacity, journal displacement, weight loss etc. has been presented. In addition to this, numerical investigations have also been performed with the numerical solution of governing Reynolds equation using FEM (finite element method) technique and Jakobsson-Floberg-Olsson (JFO) boundary condition. The experimentally obtained and theoretical results have been correlated.

Sign in / Sign up

Export Citation Format

Share Document