Study of phase behaviour and ionic effect of green surfactants in MEOR

2018 ◽  
Vol 58 (1) ◽  
pp. 84 ◽  
Author(s):  
Bashirul Haq ◽  
Jishan Liu ◽  
Keyu Liu ◽  
Dhafer Al Shehri
Keyword(s):  
Oil Recovery ◽  
Alkyl Group ◽  
Laboratory Experiments ◽  
Carbon Number ◽  
Vital Role ◽  
Phase Behaviour ◽  
Ionic Surfactant ◽  
Core Flooding ◽  
Surfactant Systems ◽  
Group Carbon

The phase behaviour of surfactant systems is an important characteristic for microbial enhanced oil recovery (MEOR) and is a key method for understanding and predicting the performance of surfactant systems. In addition, ions play a vital role in surfactant chemistry and the ionic effects of green surfactants are not yet well characterised. Green surfactants are biodegradable and environmental friendly and perceived to have great potential for MEOR. This study characterises some green anionic and non-ionic surfactants through phase behaviour study, interfacial tension (IFT) and core flooding experiments. At the same time, the combined effect of the surfactants with alcohols on IFT through laboratory experiments are looked into. Our laboratory experiments have confirmed that the non-ionic surfactant is more active in the reduction of IFT than anionic surfactant. Bio-surfactant is unable to form stable middle phase. Temperature and pressure appear to have little effect on the IFT of non-ionic surfactant. There is no significant reduction in IFT values when the non-ionic surfactant is combined with pentanol in varying concentrations. The role of alkyl group carbon number in non-ionic surfactant was also investigated in this study. It was found that the IFT value decreased by increasing the lower limit alkyl group carbon number.

scholarly journals Application Potential Analysis of Enhanced Oil Recovery by Biopolymer-Producing Bacteria and Biosurfactant-Producing Bacteria Compound Flooding

2019 ◽  
Vol 9 (23) ◽  
pp. 5119
Author(s):  
Yongqiang Bi ◽  
Jianlong Xiu ◽  
Ting Ma
Keyword(s):  
Oil Recovery ◽  
Laboratory Experiments ◽  
Fermentation Broth ◽  
Enterobacter Cloacae ◽  
Core Flooding ◽  
Heterogeneous Reservoirs ◽  
The Core ◽  
Profile Control ◽  
Application Potential ◽  
Degradation Medium

To study the feasibility of polymer-producing bacteria Enterobacter cloacae (E. cloacae) FY-07 and surfactant-producing bacteria Pseudomonas aeruginosa WJ-1 combined profile control and flooding, the compatibility of FY-07 and WJ-1 was evaluated using laboratory experiments. The results showed that the growth and metabolism of WJ-1 was not significantly affected by the FY-07 in the degradation medium, and the surface tension of fermentation broth was reduced from 70 mN/m to 30 mN/m. FY-07 enhanced the degradation of WJ-1, increasing the ratio of C14- to C15+ from 0.37 to 0.67. The core-flooding experiments indicated the oil recovery of 17.4% when both FY-07 and WJ-1 were injected into the system, as against to 10.4% and 7.9% for FY-07 and WJ-1, respectively, when injected alone. The results demonstrate a good compatibility between the FY-07 and WJ-1 strains and highlight the application potential of stain FY-07 and strain WJ-1 compound flooding for enhancing the oil recovery in heterogeneous reservoirs.

Importance of lignosulfonates in petroleum recovery operations

1981 ◽  
Vol 59 (13) ◽  
pp. 1938-1943 ◽  
Author(s):  
Graham Neale ◽  
Vladimir Hornof ◽  
Christopher Chiwetelu
Keyword(s):  
Crude Oil ◽  
Oil Recovery ◽  
Phase Behaviour ◽  
Oil Fields ◽  
Potential Importance ◽  
Mixed Surfactant ◽  
Interfacial Tensions ◽  
Mixed Surfactant Systems ◽  
Petroleum Sulfonate ◽  
Surfactant Systems

This paper reviews the potential importance of aqueous lignosulfonate solutions in the recovery of petroleum from existing partially depleted oil fields. The surfactant qualities of lignosulfonates are described and their ability to interact synergistically with petroleum sulfonate surfactants (which are currently popular in the industry) to produce ultra-low interfacial tensions with crude oil is discussed. The phase behaviour characteristics and oil recovery efficacies of these mixed surfactant systems are also examined.

Vesicular Phase Behaviour in Ionic Surfactant Systems with Organic Counter-ions

2006 ◽  
Vol 43 (1) ◽  
pp. 28-33 ◽  
Author(s):  
R. Friman ◽  
S. Backlund ◽  
C. V. Teixeira ◽  
M. Linden
Keyword(s):  
Phase Behaviour ◽  
Ionic Surfactant ◽  
Counter Ions ◽  
Surfactant Systems

Green enhanced oil recovery (GEOR)

2017 ◽  
Vol 57 (1) ◽  
pp. 150 ◽  
Author(s):  
Bashirul Haq ◽  
Jishan Liu ◽  
Keyu Liu
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Phase Behaviour ◽  
Chemical System ◽  
Core Flooding ◽  
Surfactant Mixtures ◽  
Middle Phase ◽  
Low Concentrations ◽  
Micro Emulsion ◽  
Behaviour Study

Green enhanced oil recovery (GEOR) is a chemical enhanced oil recovery (EOR) method involving the injection of specific green chemicals (surfactants/alcohols/polymers) that effectively displace oil because of their phase-behaviour properties, which decrease the interfacial tension (IFT) between the displacing liquid and the oil. In this process, the primary displacing liquid slug is a complex chemical system called a micellar solution, containing green surfactants, co-surfactants, oil, electrolytes and water. The surfactant slug is relatively small, typically 10% pore volume (PV). It may be followed by a mobility buffer such as polymer. The total volume of the polymer solution is typically ~1 PV. This study was conducted to examine the effectiveness of the combination of microbial by-products Bacillus subtilise strain JF-2 bio-surfactant and alcohol in recovering residual oil. It also considered whether bio-surfactant capability could be improved by blending it with non-ionic green surfactant. The study consisted of a phase behaviour study, IFT measurement and core-flooding experiments. In the phase behaviour study, it was found that 0.5% alkyl polyglycosides (APG) and 0.5–1.00% of butanol at 2% NaCl gave stable middle phase micro-emulsion. Non-ionic (APG 264) and anionic (bio-surfactant) mixtures are able to form stable middle phase micro-emulsion. Based on IFT reduction, two low concentrations (40 and 60 mg/l) of JF-2 bio-surfactant were identified where IFT values were low. The bio-surfactant and butanol formulation produced a total ~39.3% of oil initially in place (OIIP).

scholarly journals Effect of Environment-Friendly Non-Ionic Surfactant on Interfacial Tension Reduction and Wettability Alteration; Implications for Enhanced Oil Recovery

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3988 ◽  
Author(s):  
Omid Haghighi ◽  
Ghasem Zargar ◽  
Abbas Khaksar Manshad ◽  
Muhammad Ali ◽  
Mohammad Takassi ◽  
...  
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Co2 Storage ◽  
Water Flooding ◽  
Wettability Alteration ◽  
Ionic Surfactant ◽  
Surfactant Flooding ◽  
Core Flooding ◽  
Environment Friendly ◽  
Reservoir Rocks

Production from mature oil reservoirs can be optimized by using the surfactant flooding technique. This can be achieved by reducing oil and water interfacial tension (IFT) and modifying wettability to hydrophilic conditions. In this study, a novel green non-ionic surfactant (dodecanoyl-glucosamine surfactant) was synthesized and used to modify the wettability of carbonate reservoirs to hydrophilic conditions as well as to decrease the IFT of hydrophobic oil–water systems. The synthesized non-ionic surfactant was characterized by Fourier transform infrared spectroscopy (FTIR) and chemical shift nuclear magnetic resonance (HNMR) analyses. Further pH, turbidity, density, and conductivity were investigated to measure the critical micelle concentration (CMC) of surfactant solutions. The result shows that this surfactant alters wettability from 148.93° to 65.54° and IFT from 30 to 14 dynes/cm. Core-flooding results have shown that oil recovery was increased from 40% (by water flooding) to 59% (by surfactant flooding). In addition, it is identified that this novel non-ionic surfactant can be used in CO2 storage applications due to its ability to alter the hydrophobicity into hydrophilicity of the reservoir rocks.

Determination of Optimum Parameters for Anaerobic Thermophilic Bacterium Injection using Commercial Simulator: Core Flooding Validation and Sensitivity

2020 ◽  
Author(s):  
A. Koto
Keyword(s):  
Oil Recovery ◽  
Simulation Experiment ◽  
Previous Experiment ◽  
Core Sample ◽  
Thermophilic Bacterium ◽  
Injection Rate ◽  
Core Flooding ◽  
Optimum Parameters ◽  
Result Show

The objective of this paper is to determine the optimum anaerobic-thermophilic bacterium injection (Microbial Enhanced Oil Recovery) parameters using commercial simulator from core flooding experiments. From the previous experiment in the laboratory, Petrotoga sp AR80 microbe and yeast extract has been injected into core sample. The result show that the experiment with the treated microbe flooding has produced more oil than the experiment that treated by brine flooding. Moreover, this microbe classified into anaerobic thermophilic bacterium due to its ability to live in 80 degC and without oxygen. So, to find the optimum parameter that affect this microbe, the simulation experiment has been conducted. The simulator that is used is CMG – STAR 2015.10. There are five scenarios that have been made to forecast the performance of microbial flooding. Each of this scenario focus on the injection rate and shut in periods. In terms of the result, the best scenario on this research can yield an oil recovery up to 55.7%.

scholarly journals Investigation on degradation mechanism of polymer blockages in unconsolidated sandstone reservoirs

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 55-60
Author(s):  
Wenting Dong ◽  
Dong Zhang ◽  
Keliang Wang ◽  
Yue Qiu
Keyword(s):  
Oil Recovery ◽  
Degradation Mechanism ◽  
Injection Pressure ◽  
Polymer Flooding ◽  
Core Flooding ◽  
Reservoir Properties ◽  
Thermal Analyzer ◽  
Sandstone Reservoirs ◽  
Suction Index ◽  
Weighing Method

AbstractPolymer flooding technology has shown satisfactorily acceptable performance in improving oil recovery from unconsolidated sandstone reservoirs. The adsorption of the polymer in the pore leads to the increase of injection pressure and the decrease of suction index, which affects the effect of polymer flooding. In this article, the water and oil content of polymer blockages, which are taken from Bohai Oilfield, are measured by weighing method. In addition, the synchronous thermal analyzer and Fourier transform infrared spectroscopy (FTIR) are used to evaluate the composition and functional groups of the blockage, respectively. Then the core flooding experiments are also utilized to assess the effect of polymer plugs on reservoir properties and optimize the best degradant formulation. The results of this investigation show that the polymer adsorption in core after polymer flooding is 0.0068 g, which results in a permeability damage rate of 74.8%. The degradation ability of the agent consisting of 1% oxidizer SA-HB and 10% HCl is the best, the viscosity of the system decreases from 501.7 to 468.5 mPa‧s.

scholarly journals Photon-magnon response to fluid variability and saturation levels in sandstone reservoirs

2020 ◽  
Vol 17 (6) ◽  
pp. 1065-1074
Author(s):  
Abdullah Musa Ali ◽  
Amir Rostami ◽  
Noorhana Yahya
Keyword(s):  
Oil Recovery ◽  
Relative Permittivity ◽  
Wave Interaction ◽  
Heterogeneous Porous Media ◽  
Injection System ◽  
Bragg Grating ◽  
Fibre Bragg Grating ◽  
Core Flooding ◽  
Oil Saturation ◽  
Fluid Saturation

Abstract The need to recover high viscosity heavy oil from the residual phase of reservoirs has raised interest in the use of electromagnetics (EM) for enhanced oil recovery. However, the transformation of EM wave properties must be taken into consideration with respect to the dynamic interaction between fluid and solid phases. Consequently, this study discretises EM wave interaction with heterogeneous porous media (sandstones) under different fluid saturations (oil and water) to aid the monitoring of fluid mobility and activation of magnetic nanofluid in the reservoir. To achieve this aim, this study defined the various EM responses and signatures for brine and oil saturation and fluid saturation levels. A Nanofluid Electromagnetic Injection System (NES) was deployed for a fluid injection/core-flooding experiment. Inductance, resistance and capacitance (LRC) were recorded as the different fluids were injected into a 1.0-m long Berea core, starting from brine imbibition to oil saturation, brine flooding and eventually magnetite nanofluid flooding. The fluid mobility was monitored using a fibre Bragg grating sensor. The experimental measurements of the relative permittivity of the Berea sandstone core (with embedded detectors) saturated with brine, oil and magnetite nanofluid were given in the frequency band of 200 kHz. The behaviour of relative permittivity and attenuation of the EM wave was observed to be convolutedly dependent on the sandstone saturation history. The fibre Bragg Grating (FBG) sensor was able to detect the interaction of the Fe3O4 nanofluid with the magnetic field, which underpins the fluid mobility fundamentals that resulted in an anomalous response.

Investigation of Emulsion Flow in Steam-Assisted Gravity Drainage

SPE Journal ◽  
2013 ◽  
Vol 18 (03) ◽  
pp. 440-447 ◽  
Author(s):  
C.C.. C. Ezeuko ◽  
J.. Wang ◽  
I.D.. D. Gates
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Oil Recovery ◽  
Vital Role ◽  
Gravity Drainage ◽  
Steam Assisted Gravity Drainage ◽  
Emulsion Flow ◽  
Very High ◽  
Effective Representation

Summary We present a numerical simulation approach that allows incorporation of emulsion modeling into steam-assisted gravity-drainage (SAGD) simulations with commercial reservoir simulators by means of a two-stage pseudochemical reaction. Numerical simulation results show excellent agreement with experimental data for low-pressure SAGD, accounting for approximately 24% deficiency in simulated oil recovery, compared with experimental data. Incorporating viscosity alteration, multiphase effect, and enthalpy of emulsification appears sufficient for effective representation of in-situ emulsion physics during SAGD in very-high-permeability systems. We observed that multiphase effects appear to dominate the viscosity effect of emulsion flow under SAGD conditions of heavy-oil (bitumen) recovery. Results also show that in-situ emulsification may play a vital role within the reservoir during SAGD, increasing bitumen mobility and thereby decreasing cumulative steam/oil ratio (cSOR). Results from this work extend understanding of SAGD by examining its performance in the presence of in-situ emulsification and associated flow of emulsion with bitumen in porous media.

Sign in / Sign up

Export Citation Format

Share Document