scholarly journals Experimental analysis of basic mechanical properties of concrete upon replacement with silica fume and steel slag

2021 ◽  
Vol 889 (1) ◽  
pp. 012021
Author(s):  
Nitin Verma ◽  
Balwinder Singh
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
Experimental Analysis ◽  
Steel Slag ◽  
Experimental Investigations ◽  
Fine Aggregate ◽  
Fine Aggregates ◽  
Strength In Compression ◽  
Concrete Matrix ◽  
Constant Percentage

Abstract The prime aim in this paper is to find out the effect of Silica Fume and Steel Slag replacements for cement and fine aggregate respectively in the concrete matrix. The research included replacement of constant percentage of silica fume i.e. 10% with cement and varying percentages of steel slag replacements viz. 40%, 45%, 50% and 55% with fine aggregates. It was found from the experimental investigations that optimum results for strength in compression, flexure and split case for concrete were established on 10% of silica fume replacement for steel slag and 50% replacement of steel slag with sand.

Effect of Copper Slag as a Fine Aggregate on the Durability Characteristics of High-Performance Concrete (HPC) Containing Silica Fume

2020 ◽  
Vol 07 (02) ◽  
pp. 1-10
Author(s):  
Rizwan Ahmad Khan ◽  
Keyword(s):  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Copper Slag ◽  
Chloride Penetration ◽  
Interfacial Transition Zone ◽  
Fine Aggregate ◽  
Fresh Properties ◽  
Fine Aggregates ◽  
Effect Of Copper

This paper investigates the fresh and durability properties of the high-performance concrete by replacing cement with 15% Silica fume and simultaneously replacing fine aggregates with 25%, 50%, 75% and 100% copper slag at w/b ratio of 0.23. Five mixes were analysed and compared with the standard concrete mix. Fresh properties show an increase in the slump with the increase in the quantity of copper slag to the mix. Sorptivity, chloride penetration, UPV and carbonation results were very encouraging at 50% copper slag replacement levels. Microstructure analysis of these mixes shows the emergence of C-S-H gel for nearly all mixes indicating densification of the interfacial transition zone of the concrete.

scholarly journals Engineering and Manufacturing Technology of Green Epoxy Resin Coatings Modified with Recycled Fine Aggregates

2021 ◽  
Author(s):  
Kamil Krzywiński ◽  
Łukasz Sadowski ◽  
Damian Stefaniuk ◽  
Aleksei Obrosov ◽  
Sabine Weiß
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Construction And Demolition Waste ◽  
Fine Aggregate ◽  
Micro Computed Tomography ◽  
Demolition Waste ◽  
Replacement Ratio ◽  
Recycled Fine Aggregate ◽  
Fine Aggregates ◽  
Computed Tomography Scanning

AbstractNowadays, the recycled fine aggregate sourced from construction and demolition waste is not frequently used in manufacturing of epoxy resin coatings. Therefore, the main novelty of the article is to prepare green epoxy resin coatings modified with recycled fine aggregate in a replacement ratio of natural fine aggregate ranged from 20 to 100%. The microstructural properties of the aggregates and epoxy resin were analyzed using micro-computed tomography, scanning electron microscopy and nanoindentation. The macroscopic mechanical properties were examined using pull-off strength tests. The highest improvement of the mechanical properties was observed for epoxy resin coatings modified with 20% of natural fine aggregate and 80% of recycled fine aggregate. It has been found that even 100% of natural fine aggregate can be successfully replaced using the recycled fine aggregate with consequent improvement of the pull-off strength of analyzed epoxy resin coatings. In order to confirm the assumptions resulting from the conducted research, an original analytical and numerical failure model proved the superior behavior of modified coating was developed.

scholarly journals Experimental Study on Strength of Pervious Concrete by Using Fine Aggregate

2021 ◽  
Vol 9 (12) ◽  
pp. 895-897
Author(s):  
Atif Jawed
Keyword(s):  
Compressive Strength ◽  
Void Ratio ◽  
Rice Husk Ash ◽  
Pervious Concrete ◽  
Void Content ◽  
Fine Aggregate ◽  
Coarse Aggregates ◽  
Fine Aggregates ◽  
Flow Through ◽  
Concrete Matrix

Abstract: Pervious concrete is a special type of concrete, which consists of cement, coarse aggregates, water and if required and other cementations materials. As there are no fine aggregates used in the concrete matrix, the void content is more which allows the water to flow through its bodyThe main aim of this project was to improve the compressive strength characteristics of pervious concrete. But it can be noted that with increase in compressive strength the void ratio decreases. Hence, the improvement of strength should not affect the porosity property because it is the property which serves its purpose. In this investigation work the compressive strength of pervious concrete is increased by a maximum of 18.26% for 28 days when 8% fine aggregates were added to standard pervious concrete Keywords: W/C ratio, pervious Concrete, sugarcane bagasse’s ash, rice husk ash compressive strength, fine aggregates

The Effect of Steel Slag Coarse Aggregate on the Mechanical and Durability Performances of Concrete

2020 ◽  
Vol 833 ◽  
pp. 228-232
Author(s):  
Md. Jihad Miah ◽  
Mohammad Shamim Miah ◽  
Anisa Sultana ◽  
Taukir Ahmed Shamim ◽  
Md Ashraful Alom
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Steel Slag ◽  
Experimental Investigations ◽  
Clay Brick ◽  
Crushing Strength ◽  
Burnt Clay ◽  
Good Agreement

This work performs experimental investigations on concrete made with difference replacement percentage of first-class burnt clay brick aggregate (0, 10, 20, 30, 40, 50, 60, 80, and 100%) by steel slag (SS) aggregate. The aim is to evaluate the mechanical properties as well as durability performances, additionally, water absorption porosity test is performed to investigate the influence of steel slag aggregate on the durability of tested concrete. The experimental results have shown that the compressive strength was improved significantly due to the replacement of brick aggregate by steel slag aggregate. The crushing strength of concrete made with 100% steel slag aggregate has gained up to 70% more than the control concrete (100% brick aggregate). However, the porosity of concrete was reduced with the adding percentage of brick aggregate by steel slag aggregate which is consistent with the compressive strength results. Further, a quite good agreement between compressive strength and porosity was observed as well.

scholarly journals Prediction Models for the Mechanical Properties of Self-Compacting Concrete with Recycled Rubber and Silica Fume

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1821 ◽  
Author(s):  
Robert Bušić ◽  
Mirta Benšić ◽  
Ivana Miličević ◽  
Kristina Strukar
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Silica Fume ◽  
Prediction Models ◽  
Crumb Rubber ◽  
Fine Aggregate ◽  
Rubberized Concrete ◽  
Self Compacting Concrete ◽  
Recycled Rubber ◽  
European Standards

The paper aims to investigate the influence of waste tire rubber and silica fume on the fresh and hardened properties of self-compacting concrete (SCC) and to design multivariate regression models for the prediction of the mechanical properties of self-compacting rubberized concrete (SCRC). For this purpose, 21 concrete mixtures were designed. Crumb rubber derived from end-of-life tires (grain size 0.5–3.5 mm) was replaced fine aggregate by 0%, 5%, 10%, 15%, 20%, 25%, and 30% of total aggregate volume. Silica fume was replaced cement by 0%, 5%, and 10% of the total cement mass. The optimal replacement level of both materials was investigated in relation to the values of the fresh properties and mechanical properties of self-compacting concrete. Tests on fresh and hardened self-compacting concrete were performed according to the relevant European standards. Furthermore, models for predicting the values of the compressive strength, modulus of elasticity, and flexural strength of SCRC were designed and verified with the experimental results of 12 other studies. According to the obtained results, mixtures with up to 15% of recycled rubber and 5% of silica fume, with 28 days compressive strength above 30 MPa, were found to be optimal mixtures for the potential future investigation of reinforced self-compacting rubberized concrete structural elements.

Effect of steel slag powder, fly ash, and silica fume on the mechanical properties and durability of cement mortar

2019 ◽  
Vol 9 (9) ◽  
pp. 1049-1054
Author(s):  
Yunxia Lun ◽  
Fangfang Zheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cement Mortar ◽  
Steel Slag ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Slag Powder ◽  
Steel Slag Powder

This study is aimed at exploring the effect of steel slag powder (SSP), fly ash (FA), and silica fume (SF) on the mechanical properties and durability of cement mortar. SSP, SF, and FA were used as partial replacement of the Ordinary Portland cement (OPC). It was showed that the compressive and bending strength of steel slag powder were slightly lower than that of OPC. An increase in the SSP content caused a decrease in strength. However, the growth rate of compressive strength of SSP2 (20% replacement by the weight of OPC) at the curing ages of 90 days was about 8% higher than that of OPC, and the durability of SSP2 was better than that of OPC. The combination of mineral admixtures improved the later strength, water impermeability, and sulfate resistance compared with OPC and SSP2. The compressive strength of SSPFA (SSP and SF) at 90 days reached 70.3 MPa. The results of X-ray diffraction patterns and scanning electron microscopy indicated that SSP played a synergistic role with FA or SF to improve the performance of cement mortar.

scholarly journals “Experimental Analysis of M35 Concrete with Partial Substitute of Fine Aggregate by Nylon Glass Filled Granules and Cement by Flyash”

2019 ◽  
Vol 9 (1) ◽  
pp. 4469-4474
Keyword(s):  
Tensile Strength ◽  
Construction Industry ◽  
Experimental Analysis ◽  
Steel Fiber ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Natural Sand ◽  
Conventional Concrete ◽  
Fine Aggregates ◽  
Hardened Properties

Concrete is a material which widely used in construction industry. The present investigation deals with the study of partial replacement of fine aggregate by Nylon Glass Granules in concrete. The fine aggregates are replaced by 0%, 10%, 20% and 30% by Nylon Glass Granules by volume of natural sand in M35 grade of concrete. Additionally, to increase the tensile strength of concrete 1% of Steel Fiber by volume of cement were added to all the mixes containing Nylon Glass Granules. The concrete produced by such ingredients were cured for 7 and 28 days to evaluate its hardened properties. The 28days hardened properties of concrete revealed that maximum strength is observed for the mix which possesses 20% replacement of fine aggregate by Nylon Glass Granules compared with the conventional concrete, thus it is said to be the optimum mix

scholarly journals Characteristics of Mortars with Blast Furnace Slag Powder and Mixed Fine Aggregates Containing Ferronickel-Slag Aggregate

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5879
Author(s):  
Sung-Ho Bae ◽  
Jae-In Lee ◽  
Se-Jin Choi
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Steel Slag ◽  
Chloride Ion ◽  
Recycling Rate ◽  
Fine Aggregate ◽  
Fine Aggregates ◽  
Ferronickel Slag ◽  
Furnace Slag

Recently, interest in environmentally friendly development has increased worldwide, especially in the construction industry. In this study, blast furnace slag powder (BFSP) and mixed steel fine aggregates were applied to cement mortars to reduce the environmental damage caused by the extraction of natural aggregate and to increase the recycling rate of steel by-products in the construction industry. We investigated the fluidity, compressive strength, tensile strength, accelerated carbonation depth, and chloride ion penetration resistance of mortars with steel slag aggregate and their dependence on the presence or absence of BFSP. Because the recycling rate of ferronickel slag is low and causes environmental problems, we considered mortar samples with mixed fine aggregates containing blast furnace slag fine aggregate (BSA) and ferronickel slag fine aggregate (FSA). The results showed that the 7-day compressive strength of a sample containing both 25% BSA and 25% FSA was nearly 14.8% higher than that of the control sample. This trend is likely due to the high density and angular shape of steel slag particles. The 56-day compressive strength of the sample with BFSP and 50% FSA was approximately 64.9 MPa, which was higher than that of other samples with BFSP. In addition, the chloride ion penetrability test result indicates that the use of BFSP has a greater effect than the use of steel slag aggregate on the chloride ion penetration resistance of mortar. Thus, the substitute rate of steel slag as aggregate can be substantially enhanced if BFSP and steel slag aggregate are used in an appropriate combination.

scholarly journals Mechanical Properties of Concrete Modified with Silica Fume and Integral Waterproof and Comparison with Waste Glass Aggregate Concrete

2022 ◽  
Vol 961 (1) ◽  
pp. 012082
Author(s):  
Taghreed Abd-Almahdee Musa ◽  
Hiba Ali Abbas ◽  
Ayam Jabbar Jihad
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Silica Fume ◽  
Strength Test ◽  
Waste Glass ◽  
Fine Aggregate ◽  
Glass Aggregate ◽  
Water Proof ◽  
Strength And Durability

Abstract This study includes the effect of using different dosages of integral waterproof Admixture and silica fume on some mechanical properties of concrete. Concrete improved by using different ratios of integral water proof admixture(IWP admixture) to increase strength and durability, this admixture used as percentages from cement weight in each mix ranged from 0.0% to 2% ( 0.0, 1.0%, 1.2%,1.4%,1.6%,1.8%, and 2%), compressive strength test done for cubes with (10*10*10) cm for each mix. The flexural strength test was done by (10*10*40) cm beams and tested after 28 days of curing. comparison study was made between silica fume mixes properties and mixes without silica fume. Adding IWP admixture leads to increase mechanical properties of ordinary concrete, the reference mix shows compressive strength equal to 26.38 MPa, while mixes with 2% IWP gives 38.8 MPa in this study. The study also includes the effect of using 2 main dosages of silica fume to the mixes that contain IWP, the new concrete with two admixtures show better values of compressive, tensile and flexural strength comparing with mixes with only IWP, the compressive strength increased from 38.8 MPa for ordinary IWP mixes to 52.3 MPa for 10% silica fume concrete mixes, and also the flexural strength increased from 4.8 MPa for mixes with only IWP to 7.3 MPa for mixes modified with 10 % silica fume. Study include also using waste glass as fine aggregate in mixes contain IWP and 10% silica fume and that show more increment in mechanical properties also.

Sign in / Sign up

Export Citation Format

Share Document