scholarly journals Comparison reinforcement design shear wall modelling planar and assembly in elevator shaft

2021 ◽  
Vol 907 (1) ◽  
pp. 012004
Author(s):  
Daud Rahmat Wiyono ◽  
Roi Milyardi ◽  
Yosafat Aji Pranata ◽  
Anang Kristianto
Keyword(s):  
Shear Walls ◽  
Shear Wall ◽  
Beam Element ◽  
Longitudinal Reinforcement ◽  
Beam Shear ◽  
Vertical Beam ◽  
Wall Assembly ◽  
Reinforcement Design ◽  
Transversal Reinforcement

Abstract Shear walls modelling as planar or assembly have different assumption in behaviour that will give different responses in forces. Shear wall planar modelling as individual walls which each wall was modelled as a vertical beam. Shear Wall assembly modelling as a combined unit to be represented by one beam element. The application of shear wall assembly is placed in elevator shafts in buildings or stairwell. [1]. In ETABS program, there are two types modelling shear wall are planar walls and wall assemblies. The analysis is based on three types of design section that are Simplified Compression (C) and Tension (T), Uniform Reinforcing and General Reinforcing. The purpose of this study is comparing the planar walls Simplified C and T with planar walls Uniform Reinforcing and wall assemblies Uniform Reinforcing. The conclusion for longitudinal reinforcement are, first, planar walls Simplified C and T is 40 to 96 % larger than wall assemblies, except pier P6 is 28 % smaller, second, planar walls Uniform Reinforcing is larger than 7 to 33 % wall assemblies Uniform Reinforcing, except pier P6 is 39 % smaller, third, the planar walls Simplified C and T, planar walls Uniform Reinforcing transversal reinforcement are 1 to 8 % larger than wall assemblies Uniform Reinforcing, except pier P6 is 51 % smaller.

Research on Complex Shear Wall Bending Design

2010 ◽  
Vol 163-167 ◽  
pp. 1380-1384 ◽  
Author(s):  
Xue Yi Fu ◽  
Jia Xin Qu
Keyword(s):  
Design Method ◽  
Shear Walls ◽  
Shear Wall ◽  
Eccentric Compression ◽  
Complex Shear ◽  
Section Design ◽  
Reinforcement Design ◽  
Compression Member

Based on reference [1], complex shear wall bending design was researched farther. It was shown that reinforcement partitioned design was belonged to asymmetric reinforcement design method. It might result in the unsafe problem that ‘shear walls were designed as a little eccentric compression member, but failed as a large eccentric compression member’. Then adjusted reinforcement partitioned design method was brought forward. And it was adjusted to symmetric reinforcement design method. Then its unsafe problem was solved. But its uneconomical problem was aggravated. If this uneconomical problem could not be accepted, whole section design method of reference [1] would be suggested.

Effects of openings on the seismic behavior and performance level of concrete shear walls

2019 ◽  
Author(s):  
Hossein Alimohammadi ◽  
Mostafa Dalvi Esfahani ◽  
Mohammadali Lotfollahi Yaghin
Keyword(s):  
Static Analysis ◽  
Cross Section ◽  
Seismic Behavior ◽  
Shear Walls ◽  
Shear Wall ◽  
Constant Cross Section ◽  
Added Resistance ◽  
Different Shapes ◽  
And Performance ◽  
Abaqus Software

In this study, the seismic behavior of the concrete shear wall considering the opening with different shapes and constant cross-section has been studied, and for this purpose, several shear walls are placed under the increasingly non-linear static analysis (Pushover). These case studies modeled in 3D Abaqus Software, and the results of the ductility coefficient, hardness, energy absorption, added resistance, the final shape, and the final resistance are compared to shear walls without opening.

scholarly journals Lateral resistance of mass timber shear wall connected by withdrawal-type connectors

2021 ◽  
Vol 67 (1) ◽  
Author(s):  
Sung-Jun Pang ◽  
Kyung-Sun Ahn ◽  
Seog Goo Kang ◽  
Jung-Kwon Oh
Keyword(s):  
Experimental Data ◽  
Seismic Design ◽  
Shear Walls ◽  
Shear Wall ◽  
Vertical Load ◽  
Lateral Resistance ◽  
Kinematic Models ◽  
Mass Timber ◽  
Timber Shear Walls ◽  
Timber Shear Wall

AbstractIn this study, the lateral resistances of mass timber shear walls were investigated for seismic design. The lateral resistances were predicted by kinematic models with mechanical properties of connectors, and compared with experimental data. Four out of 7 shear wall specimens consisted of a single Ply-lam panel and withdrawal-type connectors. Three out of 7 shear wall specimens consisted of two panels made by dividing a single panel in half. The divided panels were connected by 2 or 4 connectors like a single panel before being divided. The applied vertical load was 0, 24, or 120 kN, and the number of connectors for connecting the Ply-lam wall-to-floor was 2 or 4. As a result, the tested data were 6.3 to 52.7% higher than the predicted value by kinematic models, and it means that the lateral resistance can be designed by the behavior of the connector, and the prediction will be safe. The effects of wall-to-wall connectors, wall-to-floor connectors and vertical loads on the shear wall were analyzed with the experimental data.

Study on Seismic Behavior of the L-Shape Steel Reinforced Concrete Short-Pier Shear Wall with Different Concrete Strength

2013 ◽  
Vol 353-356 ◽  
pp. 1990-1999
Author(s):  
Yi Sheng Su ◽  
Er Cong Meng ◽  
Zu Lin Xiao ◽  
Yun Dong Pi ◽  
Yi Bin Yang
Keyword(s):  
Numerical Simulation ◽  
Reinforced Concrete ◽  
Seismic Performance ◽  
Seismic Behavior ◽  
Concrete Strength ◽  
Shear Walls ◽  
Shear Wall ◽  
Simulation Software ◽  
Steel Reinforced Concrete ◽  
Shrinkage Effect

In order to discuss the effect of different concrete strength on the seismic behavior of the L-shape steel reinforced concrete (SRC) short-pier shear wall , this article analyze three L-shape steel reinforced concrete short-pier shear walls of different concrete strength with the numerical simulation software ABAQUS, revealing the effects of concrete strength on the walls seismic behavior. The results of the study show that the concrete strength obviously influence the seismic performance. With the concrete strength grade rise, the bearing capacity of the shear wall becomes large, the ductility becomes low, the pinch shrinkage effect of the hysteresis loop becomes more obvious.

Study on the shear wall structure with combined form of replaceable devices

2017 ◽  
Vol 21 (9) ◽  
pp. 1327-1348
Author(s):  
Cong Chen ◽  
Renjie Xiao ◽  
Xilin Lu ◽  
Yun Chen
Keyword(s):  
Shear Walls ◽  
Shear Wall ◽  
Performance Comparison ◽  
Wall Structure ◽  
Structural Part ◽  
Coupled Shear Wall ◽  
Wall Structures ◽  
Strength And Stiffness ◽  
Energy Dissipated ◽  
Resilient Structure

Structure with replaceable devices is a type of earthquake resilient structure developed to restore the structure immediately after strong earthquakes. Current researches focus on one type of the replaceable device located in the structural part that is most likely to be damaged; however, plastic deformation would not be limited in a specific part but expand to other parts. To concentrate possible damage in shear wall structures, combined form of replaceable devices was introduced in this article. Based on previous studies, combined form of replaceable coupling beam and replaceable wall foot was used in a coupled shear wall. Influences of the dimension and location of the replaceable devices to the strength and stiffness of the shear wall were investigated through numerical modeling, which was verified by experimental data. Performance comparison between the shear walls with one type and combined form of replaceable devices and the conventional coupled shear wall was performed. In general, the shear wall with combined form of replaceable devices is shown to be better energy dissipated, and proper dimensions and locations of the replaceable devices should be determined.

scholarly journals Steel Plate Cold-Rolled Section Steel Embedded High-Strength Concrete Low-Rise Shear Wall Seismic Performance

2018 ◽  
Vol 2018 ◽  
pp. 1-18
Author(s):  
Min Gan ◽  
Yu Yu ◽  
Liren Li ◽  
Xisheng Lu
Keyword(s):  
Bearing Capacity ◽  
Failure Mode ◽  
Seismic Performance ◽  
High Strength Concrete ◽  
Steel Plate ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Steel Plates ◽  
Strength Concrete

Four test pieces with different steel plate center-to-center distances and reinforcement ratios are subjected to low-cycle repeat quasistatic loading to optimize properties as failure mode, hysteretic curve, skeleton curve, energy dissipation parameters, strength parameters, and seismic performance of high-strength concrete low-rise shear walls. The embedded steel plates are shown to effectively restrict wall crack propagation, enhance the overall steel ratio, and improve the failure mode of the wall while reducing the degree of brittle failure. Under the same conditions, increasing the spacing between the steel plates in the steel plate concrete shear wall can effectively preserve the horizontal bearing capacity of the shear wall under an ultimate load. The embedded steel plates perform better than concealed bracing in delaying stiffness degeneration in the low-rise shear walls, thus safeguarding their long-term bearing capacity. The results presented here may provide a workable basis for shear wall design optimization.

scholarly journals Experimental Comparison Study on Cyclic Behavior of Coupled Shear Walls with Two-Level-Yielding Steel Coupling Beam and RC Coupling Beam

2018 ◽  
Author(s):  
Guoqiang LI ◽  
Mengde PANG ◽  
Feifei Sun ◽  
Liulian LI ◽  
Jianyun SUN
Keyword(s):  
Energy Dissipation ◽  
Lateral Displacement ◽  
Shear Walls ◽  
Shear Wall ◽  
Cyclic Behavior ◽  
Experimental Comparison ◽  
Coupling Beam ◽  
Coupling Beams ◽  
Coupled Shear Wall ◽  
Steel Coupling Beam

Coupled shear walls are widely used in high rise buildings, since they can not only provide efficient lateral stiffness but also behave outstanding energy dissipation ability especially for earthquake-resistance. Traditionally, the coupling beams are made of reinforced concrete, which are prone to shear failure due to low aspect ratio and greatly reduce the efficiency and ability of energy dissipation.  For overcoming the shortcoming of concrete reinforced coupling beams (RCB), an innovative steel coupling beams called two-level-yielding steel coupling beam (TYSCB) is invented to balance the demand of stiffness and energy dissipation for coupled shear walls. TYSCBs are made of two parallel steel beams with yielding at two different levels.  To verify and investigate the aseismic behaviour improvement of TYSCB-coupled shear walls, two 1/3 scale, 10-storey coupled shear wall specimens with TYSCB and RCB were tested under both gravity and lateral displacement reversals. These two specimens were designed with the same bearing capacity, thus to be easier to compare. The experimental TYSCB specimen demonstrated more robust cyclic performance. Both specimens reached 1% lateral drift, however, the TYSCB-coupled shear wall showed minimal strength degradation. Additionally, a larger amount of energy was dissipated during each test of the TYSCB specimen, compared with the RCB specimen. Based on the experimental results, design recommendations are provided.

scholarly journals Evaluation of Steel Plate Shear Wall Performance with Different Sections and Arrangements of Stiffeners and its Effect on Project Management during Construction and Improvement of the Building

2021 ◽  
Vol 11 (1) ◽  
pp. 6043-6063
Author(s):  
Ali Jafarian ◽  
Seyed Babak Jafarian
Keyword(s):  
Steel Plate ◽  
Nonlinear Dynamic Analysis ◽  
Shear Walls ◽  
Shear Wall ◽  
Economic Benefits ◽  
Lateral Loads ◽  
Steel Plate Shear Wall ◽  
High Rise ◽  
Earthquake Force ◽  
The Future

Considering the increase in the current construction process and the future needs of Iran, the necessity to use high-rise buildings for reduction in urbanization costs and optimal use of land will be inevitable in the future. The performance of steel plate shear wall system as a modern global system, which has an effective application in high-rise buildings and also brings economic benefits compared to previous systems, is evaluated in this study. Steel Plate Shear Walls (SPSW) are a new type of system resistant to wind and earthquake lateral loads, which dates back to the 1970s. In this research, eight samples of shear wall with various stiffening arrangements and sections with ST37 and ST52 alloys are modeled. To evaluate the nonlinear dynamic analysis, the samples are subjected to the San Fernando earthquake force and are modeled and analyzed by ABAQUS software based on the finite element theory. The results of analyzing the samples indicate better performance of the system with stiffener in both vertical and horizontal directions. Also, the use of sections with ST52 alloy has improved the performance of the shear wall by approximately 40%.

scholarly journals Analisis Pengaruh Lokasi Dinding Geser Terhadap Pergeseran Lateral Bangunan Bertingkat Beton Bertulang 5 Lantai

2021 ◽  
Vol 4 (1) ◽  
pp. 16
Author(s):  
Leonardus Setia Budi Wibowo ◽  
Dermawan Zebua
Keyword(s):  
Lateral Displacement ◽  
Shear Walls ◽  
Seismic Loading ◽  
Shear Wall ◽  
Structural System ◽  
Earthquake Force ◽  
Earthquake Resistant ◽  
Story Drift ◽  
Frame System ◽  
Rc Shear Wall

Indonesia is one of the countries in the earthquake region. Therefore, it is necessary to build earthquake-resistant buildings to reduce the risk of material and life losses. Reinforced Concrete (RC) shear walls is one of effective structure element to resist earthquake forces. Applying RC shear wall can effectively reduce the displacement and story-drift of the structure. This research aims to study the effect of shear wall location in symmetric medium-rise building due to seismic loading. The symmetric medium rise-building is analyzed for earthquake force by considering two types of structural system. i.e. Frame system and Dual system. First model is open frame structural system and other three models are dual type structural system. The frame with shear walls at core and centrally placed at exterior frames showed significant reduction more than 80% lateral displacement at the top of structure.

Sign in / Sign up

Export Citation Format

Share Document