Demonstration of high-performance pole pieces made of monocrystalline dysprosium for short-period undulators

2019 ◽  
Vol 26 (4) ◽  
pp. 1220-1225
Author(s):  
Takashi Tanaka ◽  
Akihiro Kagamihata
Keyword(s):  
Magnetic Flux ◽  
Curie Temperature ◽  
Saturation Magnetization ◽  
High Performance ◽  
Permanent Magnets ◽  
Magnetic Performance ◽  
Short Period ◽  
Conventional Material ◽  
Selection Of

Reported here are the results of experiments carried out to demonstrate the magnetic performance of dysprosium (Dy) to enhance the capability of undulators. Tiny pieces of monocrystalline Dy surrounded by permanent magnets (PMs) work as pole pieces (PPs) to concentrate the magnetic flux, when cooled down below the Curie temperature of 85 K. A PP made of Dy is much more attractive than one made of a conventional material, because its saturation magnetization is much higher. Furthermore, it also allows for a more flexible selection of PM material, potentially leading to further enhancement of the performance of short-period undulators. Besides these advantages, practical issues related to using Dy PPs and countermeasures against them are discussed.

scholarly journals RADIATION INDUCED DEMAGNETIZATION OF PERMANENT MAGNETS UNDER 10 MeV ELECTRON BEAM

2019 ◽  
pp. 13-16
Author(s):  
V.А. Bovda ◽  
А.М. Bovda ◽  
I.S. Guk ◽  
А.N. Dovbnya ◽  
V.N. Lyashchenko ◽  
...  
Keyword(s):  
Electron Beam ◽  
Magnetic Flux ◽  
Permanent Magnets ◽  
Absorbed Dose ◽  
Magnetic Performance ◽  
Radiation Induced

Nd-Fe-B and Sm-Co magnets were irradiated by electron beam with the energy of 10 MeV and bremsstrahlung. The absorbed dose was 16 and 160 Grad. It was found that magnetic flux of Nd-Fe-B magnets decrease with irradiation, whereas Sm-Co magnets keeps magnetic performance.

Selection of Insulating Elastomers for High-Performance Intrinsically Stretchable Transistors

2021 ◽  
Author(s):  
Hang Ren ◽  
Junmo Zhang ◽  
Yanhong Tong ◽  
Mingxin Zhang ◽  
Xiaoli Zhao ◽  
...  
Keyword(s):  
High Performance ◽  
Selection Of

scholarly journals Design of a New 1D Halbach Magnet Array with Good Sinusoidal Magnetic Field by Analyzing the Curved Surface

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2522
Author(s):  
Guangdou Liu ◽  
Shiqin Hou ◽  
Xingping Xu ◽  
Wensheng Xiao
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Permanent Magnet ◽  
Flux Density ◽  
Permanent Magnets ◽  
Air Gap ◽  
Curved Surface ◽  
Magnetic Flux Density ◽  
Sinusoidal Magnetic Field ◽  
The Magnetic Field

In the linear and planar motors, the 1D Halbach magnet array is extensively used. The sinusoidal property of the magnetic field deteriorates by analyzing the magnetic field at a small air gap. Therefore, a new 1D Halbach magnet array is proposed, in which the permanent magnet with a curved surface is applied. Based on the superposition of principle and Fourier series, the magnetic flux density distribution is derived. The optimized curved surface is obtained and fitted by a polynomial. The sinusoidal magnetic field is verified by comparing it with the magnetic flux density of the finite element model. Through the analysis of different dimensions of the permanent magnet array, the optimization result has good applicability. The force ripple can be significantly reduced by the new magnet array. The effect on the mass and air gap is investigated compared with a conventional magnet array with rectangular permanent magnets. In conclusion, the new magnet array design has the scalability to be extended to various sizes of motor and is especially suitable for small air gap applications.

scholarly journals Investigation on the La Replacement and Little Additive Modification of High-Performance Permanent Magnetic Strontium-Ferrite

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1034
Author(s):  
Ching-Chien Huang ◽  
Chin-Chieh Mo ◽  
Guan-Ming Chen ◽  
Hsiao-Hsuan Hsu ◽  
Guo-Jiun Shu
Keyword(s):  
High Performance ◽  
Single Phase ◽  
Permanent Magnets ◽  
High Efficiency ◽  
Cobalt Content ◽  
Preparation Condition ◽  
Milling Process ◽  
Experimental Parameters ◽  
La Substitution ◽  
Hard Magnets

In this work, an experiment was carried out to investigate the preparation condition of anisotropic, Fe-deficient, M-type Sr ferrite with optimum magnetic and physical properties by changing experimental parameters, such as the La substitution amount and little additive modification during fine milling process. The compositions of the calcined ferrites were chosen according to the stoichiometry LaxSr1-xFe12-2xO19, where M-type single-phase calcined powder was synthesized with a composition of x = 0.30. The effect of CaCO3, SiO2, and Co3O4 inter-additives on the Sr ferrite was also discussed in order to obtain low-temperature sintered magnets. The magnetic properties of Br = 4608 Gauss, bHc = 3650 Oe, iHc = 3765 Oe, and (BH)max = 5.23 MGOe were obtained for Sr ferrite hard magnets with low cobalt content at 1.7 wt%, which will eventually be used as high-end permanent magnets for the high-efficiency motor application in automobiles with Br > 4600 ± 50 G and iHc > 3600 ± 50 Oe.

Realizing Stable High‐Performance and Low‐Energy‐Loss Ternary Photovoltaics through Judicious Selection of the Third Component

Solar RRL ◽  
2021 ◽  
pp. 2100450
Author(s):  
Bing-Huang Jiang ◽  
Yi-Peng Wang ◽  
Yu-Wei Su ◽  
Jia-Fu Chang ◽  
Chu-Chen Chueh ◽  
...  
Keyword(s):  
Energy Loss ◽  
High Performance ◽  
Low Energy ◽  
The Third ◽  
Selection Of

scholarly journals Alloying effect on the order–disorder transformation in tetragonal FeNi

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Li-Yun Tian ◽  
Oliver Gutfleisch ◽  
Olle Eriksson ◽  
Levente Vitos
Keyword(s):  
Transition Temperature ◽  
High Performance ◽  
Density Functional ◽  
Permanent Magnets ◽  
Positive Impact ◽  
Design Strategies ◽  
Alloying Effect ◽  
Functional Theory ◽  
Disorder Transition ◽  
Disorder Transition Temperature

AbstractTetragonal ($${\hbox{L1}}_{0}$$ L1 0 ) FeNi is a promising material for high-performance rare-earth-free permanent magnets. Pure tetragonal FeNi is very difficult to synthesize due to its low chemical order–disorder transition temperature ($$\approx {593}$$ ≈ 593  K), and thus one must consider alternative non-equilibrium processing routes and alloy design strategies that make the formation of tetragonal FeNi feasible. In this paper, we investigate by density functional theory as implemented in the exact muffin-tin orbitals method whether alloying FeNi with a suitable element can have a positive impact on the phase formation and ordering properties while largely maintaining its attractive intrinsic magnetic properties. We find that small amount of non-magnetic (Al and Ti) or magnetic (Cr and Co) elements increase the order–disorder transition temperature. Adding Mo to the Co-doped system further enhances the ordering temperature while the Curie temperature is decreased only by a few degrees. Our results show that alloying is a viable route to stabilizing the ordered tetragonal phase of FeNi.

scholarly journals A Novel High Performance Discrete Flux Integrator for Control Algorithms of Fast Rotating AC Machines

2021 ◽  
Vol 11 (5) ◽  
pp. 2150
Author(s):  
Claudio Rossi ◽  
Alessio Pilati ◽  
Marco Bertoldi
Keyword(s):  
High Performance ◽  
Permanent Magnets ◽  
Machine Model ◽  
Ac Machines ◽  
Fast Calculation ◽  
Calculation Time ◽  
Digital Implementation ◽  
Rotating Speed ◽  
Interior Permanent Magnets ◽  
Accuracy Performance

This paper deals with the digital implementation of a motor control algorithm based on a unified machine model, thus usable with every traditional electric machine type (induction, brushless with interior permanent magnets, surface permanent magnets or pure reluctance). Starting from the machine equations in matrix form in continuous time, the paper exposes their discrete time transformation, suitable for digital implementation. Since the solution of these equations requires integration, the virtual division of the calculation time in sub-intervals is proposed to make the calculations more accurate. Optimization of this solver enables faster runs and higher precision especially when high rotating speed requires fast calculation time. The proposed solver is presented at different implementation levels, and its speed and accuracy performance are compared with standard solvers.

scholarly journals An Overview of Molecular Dynamic Simulation for Corrosion Inhibition of Ferrous Metals

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 46
Author(s):  
Nur Izzah Nabilah Haris ◽  
Shafreeza Sobri ◽  
Yus Aniza Yusof ◽  
Nur Kartinee Kassim
Keyword(s):  
Molecular Dynamic ◽  
Corrosion Inhibition ◽  
High Performance ◽  
Md Simulation ◽  
Ferrous Metal ◽  
Working Mechanism ◽  
Inhibitor Molecule ◽  
As Adsorption ◽  
Inhibition Studies ◽  
Selection Of

Molecular dynamics (MD) simulation is a powerful tool to study the molecular level working mechanism of corrosion inhibitors in mitigating corrosion. In the past decades, MD simulation has emerged as an instrument to investigate the interactions at the interface between the inhibitor molecule and the metal surface. Combined with experimental measurement, theoretical examination from MD simulation delivers useful information on the adsorption ability and orientation of the molecule on the surface. It relates the microscopic characteristics to the macroscopic properties which enables researchers to develop high performance inhibitors. Although there has been vast growth in the number of studies that use molecular dynamic evaluation, there is still lack of comprehensive review specifically for corrosion inhibition of organic inhibitors on ferrous metal in acidic solution. Much uncertainty still exists on the approaches and steps in performing MD simulation for corrosion system. This paper reviews the basic principle of MD simulation along with methods, selection of parameters, expected result such as adsorption energy, binding energy and inhibitor orientation, and recent publications in corrosion inhibition studies.

Mechanism of the Transition From In-Plane Buckling to Helical Buckling for a Stiff Nanowire on an Elastomeric Substrate

2016 ◽  
Vol 83 (4) ◽  
Author(s):  
Youlong Chen ◽  
Yong Zhu ◽  
Xi Chen ◽  
Yilun Liu
Keyword(s):  
High Performance ◽  
Three Dimensional ◽  
Stretchable Electronics ◽  
Buckling Mode ◽  
Design And Optimization ◽  
Out Of Plane ◽  
Plane Direction ◽  
Plane Displacement ◽  
Helical Buckling ◽  
Selection Of

In this work, the compressive buckling of a nanowire partially bonded to an elastomeric substrate is studied via finite-element method (FEM) simulations and experiments. The buckling profile of the nanowire can be divided into three regimes, i.e., the in-plane buckling, the disordered buckling in the out-of-plane direction, and the helical buckling, depending on the constraint density between the nanowire and the substrate. The selection of the buckling mode depends on the ratio d/h, where d is the distance between adjacent constraint points and h is the helical buckling spacing of a perfectly bonded nanowire. For d/h > 0.5, buckling is in-plane with wavelength λ = 2d. For 0.27 < d/h < 0.5, buckling is disordered with irregular out-of-plane displacement. While, for d/h < 0.27, buckling is helical and the buckling spacing gradually approaches to the theoretical value of a perfectly bonded nanowire. Generally, the in-plane buckling induces smaller strain in the nanowire, but consumes the largest space. Whereas the helical mode induces moderate strain in the nanowire, but takes the smallest space. The study may shed useful insights on the design and optimization of high-performance stretchable electronics and three-dimensional complex nanostructures.

Sign in / Sign up

Export Citation Format

Share Document