Influence of sour oil on calcareous deposit nucleation

2017 ◽  
Vol 64 (2) ◽  
pp. 129-135 ◽  
Author(s):  
Morteza Hoseinieh ◽  
Taghi Shahrabi ◽  
Morteza Farrokhi Rad ◽  
Bahram Ramezanzadeh
Keyword(s):  
Electrochemical Impedance ◽  
Physical Adsorption ◽  
Inhibition Mechanism ◽  
X Ray Diffraction ◽  
Steel Electrode ◽  
Content Type ◽  
X Ray ◽  
Sour Crude ◽  
Corrosion Mechanisms ◽  
Scale Deposition

Purpose The aim of this paper is to investigate the influence of sour crude oil contaminant on the calcareous scale deposition under cathodic protection of carbon steel in artificial seawater. Design/methodology/approach Electrochemical and surface characterizations are carried out using chronoamperometry, electrochemical impedance spectroscopy, scanning electron microscope/energy dispersive spectroscopy, X-Ray diffraction and Raman spectroscopy techniques. Findings Results showed that sour oil limited the deposit nucleation regarding its volume concentrations. The inhibition mechanism was examined to be simultaneous acts of pH reduction and mackinawite formation beside minor physical adsorption of oil molecules on steel electrode. Originality/value There is no paper concerning the proposed subject, and the idea of this work is fully novel which is of great significance because of the consequences of disastrous oil spill phenomena on the integrity of exposed offshore facilities in terms of optimum protection against probable corrosion mechanisms.

The para hydroxy acetanilide and acetanilide mixture for the protection from corrosion of alloyed zinc

2018 ◽  
Vol 65 (1) ◽  
pp. 1-10
Author(s):  
Daoiya Zouied ◽  
Emna Zouaoui ◽  
Mohamed Salah Medjram ◽  
Olfa Chikha ◽  
Karima Dob
Keyword(s):  
Corrosion Inhibition ◽  
Electrochemical Impedance ◽  
Physical Adsorption ◽  
Saturated Calomel Electrode ◽  
Electrochemical Techniques ◽  
Reference Electrode ◽  
Inhibition Mechanism ◽  
Zinc Electrode ◽  
Content Type ◽  
And Control

Purpose Corrosion and corrosion inhibition of alloyed zinc electrode were investigated in neutral chloride solution using electrochemical techniques. The purpose of this study is to study the corrosion inhibition of acetanilide and para hydroxy acetanilide as organics inhibitors for corrosion control of alloyed zinc electrode in NaCl 3 per cent solution. Design/methodology/approach A volt lab PGZ 301, assembled using alloyed zinc working electrode, a platinum counter electrode and a saturated calomel electrode as the reference electrode, was used in the experiment. This research was conducted using potentiodynamic polarization and electrochemical impedance spectroscopy techniques. Findings Acetanilide, para hydroxy acetanilide and their mixture provided inhibitions efficiencies of 88 per cent at 40 ppm, 87 per cent with 80 ppm and 99.86 per cent with (40 ppm AC + 80 ppm PHA), respectively. The study also discusses the corrosion inhibition mechanism of the protective layers. The adsorption of acetanilide and para hydroxy acetanilide on metal surface obeyed Langmuir’s adsorption isotherm. Polarization measurements showed that the acetanilide and the para hydroxy acetanilide, and their mixture acted as cathodic inhibitors in NaCl solution, and the inhibitor molecules followed physical adsorption on the surface of alloyed zinc. Originality/value The other new inhibitors which are very efficient inhibitors and to be applied in the field of prevention and control against corrosion.

Synergistic effect of chloride and NO2 on the atmospheric corrosion of bronze

2009 ◽  
Vol 56 (6) ◽  
pp. 299-305 ◽  
Author(s):  
Xia Cao ◽  
Ning Wang ◽  
Ning Liu
Keyword(s):  
Synergistic Effect ◽  
Design Methodology ◽  
Atmospheric Corrosion ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Impedance Measurements ◽  
Content Type ◽  
X Ray ◽  
Corrosion Kinetics ◽  
Tension Tests

PurposeThe purpose of this paper is to investigate the effect of chloride along with NO2 on the atmospheric corrosion of bronze using exposure tests.Design/methodology/approachSurface tension tests and electrochemical impedance measurements together with scanning electron microscopy (SEM) with energy dispersive atomic X‐ray, and X‐ray diffraction are used to characterize the corrosion behavior.FindingsThe results of the weight loss measurements show that the whole corrosion kinetics can be described approximately by: ΔW=atb; the synergistic effect of chloride and NO2 is observed clearly, though no nitrate existed in the corrosion products.Originality/valueA new catalyst theory has been suggested in this paper, i.e. that NO2 acts as a catalyst during the corrosion process when significant quantities of chloride also are present.

Structural, electrochemical and mechanical studies of ultrasonic irradiation enhanced electroplating Ni coating

2018 ◽  
Vol 65 (4) ◽  
pp. 333-339 ◽  
Author(s):  
Chaolei Ban ◽  
Shuqin Zhu ◽  
Jie Ma ◽  
Fangreng Wang ◽  
Zhengfeng Jia ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Ultrasonic Irradiation ◽  
Design Methodology ◽  
Electrochemical Impedance ◽  
Steel Substrate ◽  
X Ray Diffraction ◽  
Content Type ◽  
X Ray ◽  
Mechanical Studies

Purpose Ni coating was electroplated on carbon steel substrate to protect carbon steel. Design/methodology/approach During electroplating, the ultrasonic irradiation (UI) (1 kHz) action was in situ used with different frequency. The influence of UI on the microstructure, mechanical and electrochemical performance of the coating was studied with scanning electron microscopy, X-ray diffraction, microhardness measurement, polarization curves and electrochemical impedance spectroscopy. Findings The results show that comparing that without UI imposition, UI during electroplating can refine the coating grain and decrease the micro-pores in the coating, resulting in improvement of the coating corrosion and hardness. Originality/value The imposition of UI action during electroplating Ni coating can remove intrinsic pores in the coating and compact the coating. The potential bimetallic cell between substrate and plating layer can be insulated to enhance the corrosion resistance of Ni coating. The imposition of UI action during electroplating Ni coating can refine Ni coating grain size and improve the coating haredness.

The influence of hexamethylenetetramine on the structure and corrosion resistance of phosphate coating on AZ31 magnesium alloy

2016 ◽  
Vol 63 (3) ◽  
pp. 161-165 ◽  
Author(s):  
Jiansan Li ◽  
Yali Li ◽  
Yanqin Chen ◽  
Jiawei Sun ◽  
Chunxiao Wang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloys ◽  
Design Methodology ◽  
Energy Dispersive Spectrometry ◽  
Electrochemical Impedance ◽  
Phosphate Coating ◽  
X Ray Diffraction ◽  
Content Type ◽  
X Ray ◽  
Phosphate Coatings

Purpose This paper aims to report the influence of hexamethylenetetramine (HMTA) on phosphate coatings formed on AZ31 magnesium alloys. Design/methodology/approach These phosphate coatings were obtained by immersing magnesium alloys in phosphate baths with HMTA. The morphology and composition of the phosphate coatings were investigated via scanning electron microscopy, energy dispersive spectrometry and X-ray diffraction. Findings The phosphate coatings were mainly composed of CaHPO4·2H2O. The HMTA concentration in the phosphate bath influenced the crystallization and corrosion resistance of the phosphate coating. Originality/value The polarization curve shows that the anti-corrosion qualities of the phosphate coating were optimal when the HMTA concentration was 1.0 g/L in the phosphate bath. Electrochemical impedance spectroscopy (EIS) shows that the electrochemical impedances increased gradually when the HMTA concentration varied from 1.0 to 3.0 g/L.

Effect of Zn Content on Structure, Roughness and Corrosion Behavior of Zn-Ni Alloys

2019 ◽  
Vol 17 (17) ◽  
pp. 17-22
Author(s):  
Hayette Faid
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Stripping Voltammetry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Alloys ◽  
Sulfate Bath ◽  
Zn Content ◽  
Polarization Test ◽  
Δ Phase

AbstractIn this work, Zn-Ni alloys have been deposited on steel from sulfate bath, by electrodeposition method. The effect of Zn content on deposits properties was studied by cyclic voltammetry (CV), chronoaperometry (CA), linear stripping voltammetry (ALSV) and diffraction (XRD) and scanning electronic microscopy (SEM). The corrosion behavior in 3.5 wt. NaCl solution was examined using anodic polarization test and electrochemical impedance spectroscopy. X-ray diffraction of show that Zn-Ni alloys structure is composed of δ phase and γ phase, which increase with the decrease of Zn content in deposits. Results show that deposits obtained from bath less Zn2+ concentration exhibited better corrosion resistance.

Characterizations of Synthetic 8mol% YSZ with Comparison to 3mol %YSZ for HT-SOFC

2020 ◽  
Vol 38 (4A) ◽  
pp. 491-500
Author(s):  
Abeer F. Al-Attar ◽  
Saad B. H. Farid ◽  
Fadhil A. Hashim
Keyword(s):  
Ionic Conductivity ◽  
Electrochemical Impedance ◽  
Structural Information ◽  
Impedance Analysis ◽  
High Energy ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Powder Morphology ◽  
X Ray

In this work, Yttria (Y2O3) was successfully doped into tetragonal 3mol% yttria stabilized Zirconia (3YSZ) by high energy-mechanical milling to synthesize 8mol% yttria stabilized Zirconia (8YSZ) used as an electrolyte for high temperature solid oxide fuel cells (HT-SOFC). This work aims to evaluate the densification and ionic conductivity of the sintered electrolytes at 1650°C. The bulk density was measured according to ASTM C373-17. The powder morphology and the microstructure of the sintered electrolytes were analyzed via Field Emission Scanning Electron Microscopy (FESEM). The chemical analysis was obtained with Energy-dispersive X-ray spectroscopy (EDS). Also, X-ray diffraction (XRD) was used to obtain structural information of the starting materials and the sintered electrolytes. The ionic conductivity was obtained through electrochemical impedance spectroscopy (EIS) in the air as a function of temperatures at a frequency range of 100(mHz)-100(kHz). It is found that the 3YSZ has a higher density than the 8YSZ. The impedance analysis showed that the ionic conductivity of the prepared 8YSZ at 800°C is0.906 (S.cm) and it was 0.214(S.cm) of the 3YSZ. Besides, 8YSZ has a lower activation energy 0.774(eV) than that of the 3YSZ 0.901(eV). Thus, the prepared 8YSZ can be nominated as an electrolyte for the HT-SOFC.

scholarly journals Effect of Molybdenum Content on the Corrosion and Microstructure of Low-Ni, Co-Free Maraging Steels

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 852
Author(s):  
Asiful H. Seikh ◽  
Hossam Halfa ◽  
Mahmoud S. Soliman
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Microstructural Analysis ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Alloying Element ◽  
X Ray ◽  
Maraging Steels ◽  
Eds Analysis ◽  
Electroslag Refining

Molybdenum (Mo) is an important alloying element in maraging steels. In this study, we altered the Mo concentration during the production of four cobalt-free maraging steels using an electroslag refining process. The microstructure of the four forged maraging steels was evaluated to examine phase contents by optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. Additionally, we assessed the corrosion resistance of the newly developed alloys in 3.5% NaCl solution and 1 M H2SO4 solution through potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Furthermore, we performed SEM and energy-dispersive spectroscopy (EDS) analysis after corrosion to assess changes in microstructure and Raman spectroscopy to identify the presence of phases on the electrode surface. The microstructural analysis shows that the formation of retained austenite increases with increasing Mo concentrations. It is found from corrosion study that increasing Mo concentration up to 4.6% increased the corrosion resistance of the steel. However, further increase in Mo concentration reduces the corrosion resistance.

Study in performance and morphology of polyamide 12 produced by selective laser sintering technology

2018 ◽  
Vol 24 (5) ◽  
pp. 813-820 ◽  
Author(s):  
Junjie Wu ◽  
Xiang Xu ◽  
Zhihao Zhao ◽  
Minjie Wang ◽  
Jie Zhang
Keyword(s):  
Selective Laser Sintering ◽  
Polarized Light ◽  
Chain Scission ◽  
High Energy ◽  
Laser Sintering ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Content Type ◽  
X Ray ◽  
Polyamide 12

Purpose The purpose of this paper is to investigate the effect of selective laser sintering (SLS) method on morphology and performance of polyamide 12. Design/methodology/approach Crystallization behavior is critical to the properties of semi-crystalline polymers. The crystallization condition of SLS process is much different from others. The morphology of polyamide 12 produced by SLS technology was investigated using scanning electron microscopy, polarized light microscopy, differential scanning calorimetry, X-ray diffraction and wide-angle X-ray diffraction. Findings Too low fill laser power brought about bad fusion of powders, while too high energy input resulted in bad performance due to chain scission of macromolecules. There were three types of crystal in the raw powder material, denoted as overgrowth crystal, ring-banded spherulite and normal spherulite. Originality/value In this work, SLS samples with different sintering parameters, as well as compression molding sample for the purpose of comparison, were made to study the morphology and crystal structure of sintered PA12 in detail.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Structure and Electrochemical Behavior of Plasma-Sprayed LSGM Electrolyte Films

2002 ◽  
Vol 756 ◽  
Author(s):  
H. Zhang ◽  
X. Ma ◽  
J. Dai ◽  
S. Hui ◽  
J. Roth ◽  
...  
Keyword(s):  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
Amorphous Structure ◽  
Solid Oxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spray Process ◽  
Plasma Spray Process ◽  
Electrolyte Film ◽  
Plasma Sprayed

ABSTRACTAn intermediate temperature solid oxide fuel cell (SOFC) electrolyte film of La0.8Sr 0.2Ga0.8Mg0.2O2.8 (LSGM) was fabricated using a plasma spray process. The microstructure and phase were investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical behavior of the thermal sprayed LSGM film was investigated using electrochemical impedance spectroscopy (EIS). The study indicates that thermal spray can deposit a dense LSGM layer. It was found that the rapid cooling in the thermal process led to an amorphous or poor crystalline LSGM deposited layer. This amorphous structure has a significant effect on the performance of the cell. Crystallization of the deposited LSGM layer was observed during annealing between 500–600 °C. After annealing at 800 °C, the ionic conductivity of the sprayed LSGM layer can reach the same level as that of the sintered LSGM.

Sign in / Sign up

Export Citation Format

Share Document