The effects of using ceiling fans on human thermal comfort in a three-dimensional room with centralized heating including an occupant

2019 ◽  
Vol 29 (10) ◽  
pp. 3976-3993 ◽  
Author(s):  
Mahdi Ashoori ◽  
Ghanbarali Sheikhzadeh ◽  
Soroush Sadripour
Keyword(s):  
Heat Transfer ◽  
Thermal Comfort ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Heating System ◽  
Considerable Effect ◽  
Content Type ◽  
Human Thermal Comfort ◽  
Air Speed ◽  
Comfort Condition

Purpose The purpose of this study is to analyze the effect of using a ceiling fan with central heating system in the winter on thermal comfort and heat transfer rate in a three-dimensional numerically. Design/methodology/approach The geometry had certain dimensions, and an occupant was modeled to be in the room. In models which were used, the flow was turbulent, and turbulence models were used for simulating turbulence. Between all the models, k-ε model had best matching. Findings Results show that using the ceiling fan during the winter had an efficient and considerable effect on improving the thermal comfort and energy saving inside buildings. By the use of ceiling fan, the effective room temperature has increased by 2.5°C. Furthermore, results show that by using ceiling fan in the winter, the predicted mean vote and the predicted percentage dissatisfied indexes improved. At the end, the case Room 11-0.05-15 with temperature of 87°C for radiator and normal fan velocity of o.25m/s were the optimal model that caused the complete thermal comfort and reduced energy consumption up to 28 per cent. Originality/value In the present study, the effects of using the ceiling fans on human comfort condition and heat transfer field during the winter (heating system) are studied. Following are the goals for all models: getting the appropriate temperature for radiator so that thermal comfort condition can be applied at the height of 75 cm of the room, velocity for fan so that air speed can be 0.25m/s at the height of 2 m or lower of the room and position to place the fan.

Investigation on thermal comfort of the uniform for workers in tropical monsoon climates

2020 ◽  
Vol 32 (6) ◽  
pp. 849-868
Author(s):  
Jingxian Xu ◽  
Huijuan Liu ◽  
Yunyi Wang ◽  
Jun Li
Keyword(s):  
Heat Transfer ◽  
Thermal Comfort ◽  
Dynamic Condition ◽  
Thermal Manikin ◽  
Content Type ◽  
Wind Speeds ◽  
Subjective Perceptions ◽  
Tropical Monsoon ◽  
Four Levels ◽  
Thermal Insulations

PurposeThis study aims to investigate the heat transfer mechanism of the uniforms used by people working in hot, humid and windy environments. Furthermore, the effectiveness of an opening structure added to the armpit of the uniforms in improving thermal comfort was comparatively examined.Design/methodology/approachA set of uniforms was tested with the opening at the armpit alternatively zipped or unzipped. Thermal manikin and human tests were performed in a climatic chamber simulating the specific environmental conditions, including wind speeds at four levels (0.15, 0.5, 2, 4 m/s) and relative humidities at two levels (50 and 85%). Static and dynamic thermal insulations of clothing (IT) were examined by the thermal manikin tests. The human bodies' thermal responses, including heart rates (HR), eardrum temperatures (Te), skin temperatures (Tsk) and subjective perceptions, were given by the human tests.FindingsSpecial mechanisms of heat transfer in the specific uniforms used in tropical monsoon climates were revealed. Reductions on IT were caused by the movement of the human body and the environmental wind, and the empirical equations would underestimate this reduction. The opening at the armpit was able to prompt more heat transfer under dynamic condition, with reducing the IT by 11.8%, lowering the mean Tsk by 0.92°C, and significantly improving the subjective perceptions (p < 0.05). The heat exhaustion was alleviated with lowering the Te by 0.32°C.Originality/valueThis study managed to improve the thermal performance of uniforms for workers under unforgiving conditions. The evaluation and design methods introduced by this study provided practical guidance for similar products with strict dress codes and cost control requirements based on the findings from thorough product tests and analysis.

scholarly journals Comparison of Two-Equation Turbulence Models for Prediction of Heat Transfer on Film-Cooled Turbine Blades

1997 ◽  
Author(s):  
Vijay K. Garg ◽  
Ali A. Ameri
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Computer Time ◽  
Suction Surface ◽  
The Heat Transfer Coefficient

A three-dimensional Navier-Stokes code has been used to compute the heat transfer coefficient on two film-cooled turbine blades, namely the VKI rotor with six rows of cooling holes including three rows on the shower head, and the C3X vane with nine rows of holes including five rows on the shower head. Predictions of heat transfer coefficient at the blade surface using three two-equation turbulence models, specifically, Coakley’s q-ω model, Chien’s k-ε model and Wilcox’s k-ω model with Menter’s modifications, have been compared with the experimental data of Camci and Arts (1990) for the VKI rotor, and of Hylton et al. (1988) for the C3X vane along with predictions using the Baldwin-Lomax (B-L) model taken from Garg and Gaugler (1995). It is found that for the cases considered here the two-equation models predict the blade heat transfer somewhat better than the B-L model except immediately downstream of the film-cooling holes on the suction surface of the VKI rotor, and over most of the suction surface of the C3X vane. However, all two-equation models require 40% more computer core than the B-L model for solution, and while the q-ω and k-ε models need 40% more computer time than the B-L model, the k-ω model requires at least 65% more time due to slower rate of convergence. It is found that the heat transfer coefficient exhibits a strong spanwise as well as streamwise variation for both blades and all turbulence models.

Numerical Simulations of Heat Transfer and Fluid Flow for a Rotating High-Pressure Turbine

2006 ◽  
Author(s):  
F. Mumic ◽  
L. Ljungkruna ◽  
B. Sunden
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Fluid Flow ◽  
Numerical Study ◽  
Three Dimensional ◽  
Turbulence Models ◽  
High Pressure Turbine ◽  
Experimental Heat ◽  
Commercial Code ◽  
Stator Vane

In this work, a numerical study has been performed to simulate the heat transfer and fluid flow in a transonic high-pressure turbine stator vane passage. Four turbulence models (the Spalart-Allmaras model, the low-Reynolds-number realizable k-ε model, the shear-stress transport (SST) k-ω model and the v2-f model) are used in order to assess the capability of the models to predict the heat transfer and pressure distributions. The simulations are performed using the FLUENT commercial software package, but also two other codes, the in-house code VolSol and the commercial code CFX are used for comparison with FLUENT results. The results of the three-dimensional simulations are compared with experimental heat transfer and aerodynamic results available for the so-called MT1 turbine stage. It is observed that the predictions of the vane pressure field agree well with experimental data, and that the pressure distribution along the profile is not strongly affected by choice of turbulence model. It is also shown that the v2-f model yields the best agreement with the measurements. None of the tested models are able to predict transition correctly.

Pressure Drop and Heat Transfer Characteristics of Louvered Fin Heat Exchangers

2013 ◽  
Vol 465-466 ◽  
pp. 500-504 ◽  
Author(s):  
Shahrin Hisham Amirnordin ◽  
Hissein Didane Djamal ◽  
Mohd Norani Mansor ◽  
Amir Khalid ◽  
Md Seri Suzairin ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Heat Exchangers ◽  
Transfer Rate ◽  
Three Dimensional ◽  
Considerable Effect ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Louvered Fin

This paper presents the effect of the changes in fin geometry on pressure drop and heat transfer characteristics of louvered fin heat exchanger numerically. Three dimensional simulation using ANSYS Fluent have been conducted for six different configurations at Reynolds number ranging from 200 to 1000 based on louver pitch. The performance of this system has been evaluated by calculating pressure drop and heat transfer coefficient. The result shows that, the fin pitch and the louver pitch have a very considerable effect on pressure drop as well as heat transfer rate. It is observed that increasing the fin pitch will relatively result in an increase in heat transfer rate but at the same time, the pressure drop will decrease. On the other hand, low pressure drop and low heat transfer rate will be obtained when the louver pitch is increased. Final result shows a good agreement between experimental and numerical results of the louvered fin which is about 12%. This indicates the capability of louvered fin in enhancing the performance of heat exchangers.

Computational analysis of convective heat transfer properties of turbulent slot jet impingement

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Anuj Kumar Shukla ◽  
Anupam Dewan
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
High Efficiency ◽  
Stokes Equations ◽  
Turbulence Models ◽  
Jet Impingement ◽  
Complex Flow ◽  
Content Type

Purpose Convective heat transfer features of a turbulent slot jet impingement are comprehensively studied using two different computational approaches, namely, URANS (unsteady Reynolds-averaged Navier–Stokes equations) and SAS (scale-adaptive simulation). Turbulent slot jet impingement heat transfer is used where a considerable heat transfer enhancement is required, and computationally, it is a quite challenging flow configuration. Design/methodology/approach Customized OpenFOAM 4.1, an open-access computational fluid dynamics (CFD) code, is used for SAS (SST-SAS k-ω) and URANS (standard k-ε and SST k-ω) computations. A low-Re version of the standard k-ε model is used, and other models are formulated for good wall-refined calculations. Three turbulence models are formulated in OpenFOAM 4.1 with second-order accurate discretization schemes. Findings It is observed that the profiles of the streamwise turbulence are under-predicted at all the streamwise locations by SST k-ω and SST SAS k-ω models, but follow similar trends as in the reported results. The standard k-ε model shows improvements in the predictions of the streamwise turbulence and mean streamwise velocity profiles in the zone of outer wall jet. Computed profiles of Nusselt number by SST k-ω and SST-SAS k-ω models are nearly identical and match well with the reported experimental results. However, the standard k-ε model does not provide a reasonable profile or quantification of the local Nusselt number. Originality/value Hybrid turbulence model is suitable for efficient CFD computations for the complex flow problems. This paper deals with a detailed comparison of the SAS model with URANS and LES for the first time in the literature. A thorough assessment of the computations is performed against the results reported using experimental and large eddy simulations techniques followed by a detailed discussion on flow physics. The present results are beneficial for scientists working with hybrid turbulence models and in industries working with high-efficiency cooling/heating system computations.

Investigation of the effects of geometrical parameters, eccentricity and perforated fins on natural convection heat transfer in a finned horizontal annulus using three dimensional lattice Boltzmann flux solver

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mahyar Ashouri ◽  
Mohammad Mehdi Zarei ◽  
Ali Moosavi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Lattice Boltzmann ◽  
Transfer Rate ◽  
Three Dimensional ◽  
Maximum Heat ◽  
Content Type ◽  
Dimensional Lattice ◽  
Fin Spacing

Purpose The purpose of this paper is to investigate the effects of geometrical parameters, eccentricity and perforated fins on natural convection heat transfer in a finned horizontal annulus using three-dimensional lattice Boltzmann flux solver. Design/methodology/approach Three-dimensional lattice Boltzmann flux solver is used in the present study for simulating conjugate heat transfer within an annulus. D3Q15 and D3Q7 models are used to solve the fluid flow and temperature field, respectively. The finite volume method is used to discretize mass, momentum and energy equations. The Chapman–Enskog expansion analysis is used to establish the connection between the lattice Boltzmann equation local solution and macroscopic fluxes. To improve the accuracy of the lattice Boltzmann method for curved boundaries, lattice Boltzmann equation local solution at each cell interface is considered to be independent of each other. Findings It is found that the maximum heat transfer rate occurs at low fin spacing especially by increasing the fin height and decreasing the internal-cylindrical distance. The effect of inner cylinder eccentricity is not much considerable (up to 5.2% enhancement) while the impact of fin eccentricity is more remarkable. Negative fin eccentricity further enhances the heat transfer rate compared to a positive fin eccentricity and the maximum heat transfer enhancement of 91.7% is obtained. The influence of using perforated fins is more considerable at low fin spacing although some heat transfer enhancements are observed at higher fin spacing. Originality/value The originality of this paper is to study three-dimensional natural convection in a finned-horizontal annulus using three-dimensional lattice Boltzmann flux solver, as well as to apply symmetry and periodic boundary conditions and to analyze the effect of eccentric annular fins (for the first time for air) and perforated annular fins (for the first time so far) on the heat transfer rate.

Fluid flow and heat transfer of a stratified system during natural convection – influence of chamfered corners

2019 ◽  
Vol 29 (2) ◽  
pp. 470-486 ◽  
Author(s):  
Alireza Rahimi ◽  
Aravindhan Surendar ◽  
Aygul Z. Ibatova ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Three Dimensional ◽  
Immiscible Fluids ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose This paper aims to investigate the three-dimensional natural convection and entropy generation in the rectangular cuboid cavities included by chamfered triangular partition made by polypropylene. Design/methodology/approach The enclosure is filled by multi-walled carbon nanotubes (MWCNTs)-H2O nanofluid and air as two immiscible fluids. The finite volume approach is used for computation. The fluid flow and heat transfer are considered with combination of local entropy generation due to fluid friction and heat transfer. Moreover, a numerical method is developed based on three-dimensional solution of Navier–Stokes equations. Findings Effects of side ratio of triangular partitions (SR = 0.5, 1 and 2), Rayleigh number (103 < Ra < 105) and solid volume fraction (f = 0.002, 0.004 and 0.01 Vol.%) of nanofluid are investigated on both natural convection characteristic and volumetric entropy generation. The results show that the partitions can be a suitable method to control fluid flow and energy consumption, and three-dimensional solutions renders more accurate results. Originality/value The originality of this work is to study the three-dimensional natural convection and entropy generation of a stratified system.

Computation of flow and heat transfer through channels with periodic dimple/protrusion walls using low-Reynolds number turbulence models

2019 ◽  
Vol 29 (3) ◽  
pp. 1178-1207 ◽  
Author(s):  
Mohammad Fazli ◽  
Mehrdad Raisee
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Correction Term ◽  
Turbine Blades ◽  
Turbulence Models ◽  
Internal Cooling ◽  
Recirculation Bubble ◽  
Content Type ◽  
Flow And Heat Transfer ◽  
Numerical Predictions

PurposeThis paper aims to predict turbulent flow and heat transfer through different channels with periodic dimple/protrusion walls. More specifically, the performance of various low-Rek-ε turbulence models in prediction of local heat transfer coefficient is evaluated.Design/methodology/approachThree low-Re numberk-εturbulence models (the zonalk-ε, the lineark-εand the nonlineark-ε) are used. Computations are performed for three geometries, namely, a channel with a single dimpled wall, a channel with double dimpled walls and a channel with a single dimple/protrusion wall. The predictions are obtained using an in house finite volume code.FindingsThe numerical predictions indicate that the nonlineark-εmodel predicts a larger recirculation bubble inside the dimple with stronger impingement and upwash flow than the zonal and lineark-εmodels. The heat transfer results show that the zonalk-εmodel returns weak thermal predictions in all test cases in comparison to other turbulence models. Use of the lineark-εmodel leads to improvement in heat transfer predictions inside the dimples and their back rim. However, the most accurate thermal predictions are obtained via the nonlineark-εmodel. As expected, the replacement of the algebraic length-scale correction term with the differential version improves the heat transfer predictions of both linear and nonlineark-εmodels.Originality/valueThe most reliable turbulence model of the current study (i.e. nonlineark-εmodel) may be used for design and optimization of various thermal systems using dimples for heat transfer enhancement (e.g. heat exchangers and internal cooling system of gas turbine blades).

Unsteady mixed convection flow at a three-dimensional stagnation point

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Amin Noor ◽  
Roslinda Nazar ◽  
Kohilavani Naganthran ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Mixed Convection ◽  
Stagnation Point ◽  
Three Dimensional ◽  
Convection Flow ◽  
Mixed Convection Flow ◽  
Content Type ◽  
Flow And Heat Transfer ◽  
Unsteady Mixed Convection

Purpose This paper aims to probe the problem of an unsteady mixed convection stagnation point flow and heat transfer past a stationary surface in an incompressible viscous fluid numerically. Design/methodology/approach The governing nonlinear partial differential equations are transformed into a system of ordinary differential equations by a similarity transformation, which is then solved numerically by a Runge – Kutta – Fehlberg method with shooting technique and a collocation method, namely, the bvp4c function. Findings The effects of the governing parameters on the fluid flow and heat transfer characteristics are illustrated in tables and figures. It is found that dual (upper and lower branch) solutions exist for both the cases of assisting and opposing flow situations. A stability analysis has also been conducted to determine the physical meaning and stability of the dual solutions. Practical implications This theoretical study is significantly relevant to the applications of the heat exchangers placed in a low-velocity environment and electronic devices cooled by fans. Originality/value The case of suction on unsteady mixed convection flow at a three-dimensional stagnation point has not been studied before; hence, all generated numerical results are claimed to be novel.

Effect of solar radiation on human thermal comfort in a tropical climate

2020 ◽  
pp. 1420326X1989176 ◽  
Author(s):  
Somsak Chaiyapinunt ◽  
Nopparat Khamporn
Keyword(s):  
Solar Radiation ◽  
Surface Temperature ◽  
Thermal Comfort ◽  
Human Body ◽  
Glass Surface ◽  
Tropical Climate ◽  
Direct Solar Radiation ◽  
Diffuse Solar Radiation ◽  
Human Thermal Comfort ◽  
Comfort Condition

The contribution of solar radiation on the global thermal comfort and local thermal comfort condition for a person sitting near a glass window in a building located in a tropical climate was studied. The effects of transmitted direct solar radiation, transmitted diffuse solar radiation, inside glass surface temperature and distance of a seated person from the glass window on the predicted percentage of dissatisfied (PPD) and plane radiant temperature asymmetry (RTA) were studied. PPD and RTA due to transmitted diffuse solar radiation and high inside glass surface temperature were decreased with the distance from the glass window. PPD was decreased exponentially with the distance from the glass window, while RTA was decreased slowly with the distance from the glass window. The findings show that PPD and RTA due to transmitted direct solar radiation striking the human body are not dependent on the distance from the glass window, but they are dependent on the magnitude and direction of the solar beam radiation incident on a human body. The results of the study would help the building designers to be able to design the interior working space for the tenant sitting near the glass window to achieve the acceptable level of thermal comfort condition.

Sign in / Sign up

Export Citation Format

Share Document