Heat transfer within linear Fresnel unit using parabolic reflector

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Z. Ebrahimpour ◽  
Seyyed Ali Farshad ◽  
M. Sheikholeslami
Keyword(s):  
Heat Flux ◽  
Solar Radiation ◽  
Incident Radiation ◽  
Heat Losses ◽  
Exergy Loss ◽  
Optimized Design ◽  
Radiation Mode ◽  
Content Type ◽  
Parabolic Shape ◽  
Linear Fresnel Reflector

Purpose This paper scrutinizes exergy loss and hydrothermal analysis of Linear Fresnel Reflector (LFR) unit by means of FLUENT. Several mirrors were used to guide the solar radiation inside the receiver, which has parabolic shape. Radiation model was used to simulate radiation mode. Design/methodology/approach Heat losses from receiver should be minimized to reach the optimized design. Outputs were summarized as contours of incident radiation, isotherm and streamline. Outputs were classified in terms of contours and plots to depict the influence of temperature of hot wall, wind velocity and configurations on performance of Linear Fresnel Reflector (LFR) based on thermal and exergy treatment. Four arrangements for LFR units are considered and all of them have same height. Findings Greatest Nu and Ex can be obtained for case D due to the highest heat loss from hot wall. Share of radiative heat flux relative to total heat flux is about 94% for case D. In case D when Tr = 0.388, As hext rises from 5 to 20, Nutotal enhances about 11.42% when Tr = 0.388. By selecting case D instead of case A, Ex rises about 16.14% for lowest Tr. Nutotal and Ex of case D augment by 3.65 and 6.23 times with rise of Tr when hext = 5. To evaluate the thermal performance (ηth) of system, absorber pipe was inserted below the parabolic reflector and 12 mirrors were used above the ground. The outputs revealed that ηth decreases about 14.31% and 2.54% with augment of Tin and Q if other factors are minimum. Originality value This paper scrutinizes exergy loss and hydrothermal analysis of LFR unit by means of finite volume method. Several mirror used to guide the solar radiation inside the receiver, which has parabolic shape. DO model was used to simulate radiation mode. Heat losses from receiver should be minimized to reach the optimized design. Outputs were summarized as contours of incident radiation, isotherm and streamline.

Application of generalized Fourier heat conduction law on MHD viscoinelastic fluid flow over stretching surface

2019 ◽  
Vol 30 (6) ◽  
pp. 3481-3496 ◽  
Author(s):  
Arif Hussain ◽  
Muhammad Yousaf Malik ◽  
Mair Khan ◽  
Taimoor Salahuddin
Keyword(s):  
Heat Flux ◽  
Fluid Flow ◽  
Friction Factor ◽  
Numerical Technique ◽  
Wall Heat Flux ◽  
Constitutive Law ◽  
Wall Friction ◽  
Theoretical Physics ◽  
Stretching Surface ◽  
Content Type

Purpose The purpose of current flow configuration is to spotlights the thermophysical aspects of magnetohydrodynamics (MHD) viscoinelastic fluid flow over a stretching surface. Design/methodology/approach The fluid momentum problem is mathematically formulated by using the Prandtl–Eyring constitutive law. Also, the non-Fourier heat flux model is considered to disclose the heat transfer characteristics. The governing problem contains the nonlinear partial differential equations with appropriate boundary conditions. To facilitate the computation process, the governing problem is transmuted into dimensionless form via appropriate group of scaling transforms. The numerical technique shooting method is used to solve dimensionless boundary value problem. Findings The expressions for dimensionless velocity and temperature are found and investigated under different parametric conditions. The important features of fluid flow near the wall, i.e. wall friction factor and wall heat flux, are deliberated by altering the pertinent parameters. The impacts of governing parameters are highlighted in graphical as well as tabular manner against focused physical quantities (velocity, temperature, wall friction factor and wall heat flux). A comparison is presented to justify the computed results, it can be noticed that present results have quite resemblance with previous literature which led to confidence on the present computations. Originality/value The computed results are quite useful for researchers working in theoretical physics. Additionally, computed results are very useful in industry and daily-use processes.

Investigation of slip/no-slip surface for two-dimensional large tilting pad thrust bearing

2017 ◽  
Vol 69 (6) ◽  
pp. 995-1004 ◽  
Author(s):  
Zhixiang Song ◽  
Fei Guo ◽  
Ying Liu ◽  
Songtao Hu ◽  
Xiangfeng Liu ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Slip Surface ◽  
Load Capacity ◽  
Slip Condition ◽  
Optimized Design ◽  
Two Dimensional ◽  
Boundary Slip ◽  
Content Type ◽  
Tilting Pad ◽  
Turbulence Effect

Purpose This paper aims to present the slip/no-slip design in two-dimensional water-lubricated tilting pad thrust bearings (TPTBs) considering the turbulence effect and shifting of pressure centers. Design/methodology/approach A numerical model is established to analyze the slip condition and the effect of turbulence according to a Reynolds number defined in terms of the slip condition. Simulations are carried out for eccentrically and centrally pivoted bearings and the influence of different slip parameters is discussed. Findings A considerable enhancement in load capacity, as well as a reduction in friction, can be achieved by heterogeneous slip/no-slip surface designs for lubricated sliding contacts, especially for near parallel pad configurations. The optimized design largely depends on the pivot position. The load capacity increases by 174 per cent for eccentrically pivoted bearings and 159 per cent for centrally pivoted bearings for a suitable design. When slip zone locates at the middle of the radial direction or close to the inner edge, the performance of the TPTB is better. Research limitations/implications The simplification of slip effect on the turbulence (definition of Reynolds number) can only describe the trend of the increasing turbulence due to slip condition. The accurate turbulence expression considering the boundary slip needs further explorations. Originality/value The shifting of pressure center due to the slip/no-slip design for TPTBs is investigated in this study. The turbulence effect and influence of slip parameters is discussed for large water-lubricated bearings.

An alternative approach to thermal analysis using inverse problems in aluminum alloy welding

2017 ◽  
Vol 27 (3) ◽  
pp. 561-574 ◽  
Author(s):  
Elisan dos Santos Magalhaes ◽  
Cristiano Pedro da Silva ◽  
Ana Lúcia Fernandes Lima e Silva ◽  
Sandro Metrevelle Marcondes Lima e Silva
Keyword(s):  
Thermal Analysis ◽  
Heat Flux ◽  
Aluminum Alloy ◽  
Inverse Problems ◽  
Welding Process ◽  
Experimental Methodology ◽  
Function Technique ◽  
Content Type ◽  
Radiation Coefficient ◽  
Welding Processes

Purpose The purpose of this article is the determination of the temperature fields in a weld region has always been an obstacle to the improvement of welding processes. As an alternative, the use of inverse problems to determine the heat flux during the welding process allows an analysis of these processes. Design/methodology/approach This paper studies an alternative for the thermal analysis of the tungsten inert gas welding process on a 6,060 T5 aluminum alloy. For this purpose, a C++ code was developed, based on a transient three-dimensional heat transfer model. To estimate the amount of heat delivered to the plate, the specification function technique was used. Lab experiments were carried out to validate the methodology. A different experimental methodology is proposed to estimate the emissivity (radiation coefficient). Findings The maximum difference between experimental and numerical temperatures is lower than 5 per cent. The determined emissivity value for the aluminum 6,060 T5 presented a good agreement with literature values. The thermal fields were analyzed as function of the positive polarity. The specification function method proved to be an adequate tool for heat input estimation in welding analysis. Originality/value The proposed methodology proves to be a cheaper way to estimate the heat flux on the sample. The estimated power curves for the welding process are presented. The methodology to calculate the emissivity (radiation coefficient) was validated.

Modelling of a Phase Change Material melting process heated from below using spectral collocation methods

2014 ◽  
Vol 24 (3) ◽  
pp. 697-734 ◽  
Author(s):  
Jean Batina ◽  
Serge Blancher ◽  
Tarik Kouskou
Keyword(s):  
Heat Flux ◽  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Textile Industry ◽  
Present Model ◽  
Good Accuracy ◽  
Content Type ◽  
Energy Equations ◽  
Change Material

Purpose – Mathematical and numerical models are developed to study the melting of a Phase Change Material (PCM) inside a 2D cavity. The bottom of the cell is heated at constant and uniform temperature or heat flux, assuming that the rest of the cavity is completely adiabatic. The paper used suitable numerical methods to follow the interface temporal evolution with a good accuracy. The purpose of this paper is to show how the evolution of the latent energy absorbed to melt the PCM depends on the temperature imposed on the lower wall of the cavity. Design/methodology/approach – The problem is written with non-homogeneous boundary conditions. Momentum and energy equations are numerically solved in space by a spectral collocation method especially oriented to this situation. A Crank-Nicolson scheme permits the resolution in time. Findings – The results clearly show the evolution of multicellular regime during the process of fusion and the kinetics of phase change depends on the boundary condition imposed on the bottom cell wall. Thus the charge and discharge processes in energy storage cells can be controlled by varying the temperature in the cell PCM. Substantial modifications of the thermal convective heat and mass transfer are highlighted during the transient regime. This model is particularly suitable to follow with a good accuracy the evolution of the solid/liquid interface in the process of storage/release energy. Research limitations/implications – The time-dependent physical properties that induce non-linear coupled unsteady terms in Navier-Stokes and energy equations are not taken into account in the present model. The present model is actually extended to these coupled situations. This problem requires smoother geometries. One can try to palliate this disadvantage by constructing smoother approximations of non-smooth geometries. The augmentation of polynomials developments orders increases strongly the computing time. When the external heat flux or temperature imposed at the PCM is much greater than the temperature of the PCM fusion, one must choose carefully some data to assume the algorithms convergence. Practical implications – Among the areas where this work can be used, are: buildings where the PCM are used in insulation and passive cooling; thermal energy storage, the PCM stores energy by changing phase, solid to liquid (fusion); cooling and transport of foodstuffs or pharmaceutical or medical sensitive products, the PCM is used in the food industry, pharmaceutical and medical, to minimize temperature variations of food, drug or sensitive materials; and the textile industry, PCM materials in the textile industry are used in microcapsules placed inside textile fibres. The PCM intervene to regulate heat transfer between the body and the outside. Originality/value – The paper's originality is reflected in the precision of its results, due to the use of a high-accuracy numerical approximation based on collocation spectral methods, and the choice of Chebyshev polynomials basis in both axial and radial directions.

Numerical study of Carreau nanofluid flow past vertical plate with the Cattaneo–Christov heat flux model

2019 ◽  
Vol 29 (2) ◽  
pp. 702-723 ◽  
Author(s):  
Vasu B. ◽  
Atul Kumar Ray
Keyword(s):  
Heat Flux ◽  
Brownian Motion ◽  
Weissenberg Number ◽  
Motion Parameter ◽  
Conduction Model ◽  
Content Type ◽  
Carreau Nanofluid ◽  
Flux Model ◽  
Heat Flux Model ◽  
Brownian Motion Parameter

PurposeTo achieve material-invariant formulation for heat transfer of Carreau nanofluid, the effect of Cattaneo–Christov heat flux is studied on a natural convective flow of Carreau nanofluid past a vertical plate with the periodic variations of surface temperature and the concentration of species. Buongiorno model is considered for nanofluid transport, which includes the relative slip mechanisms, Brownian motion and thermophoresis.Design/methodology/approachThe governing equations are non-dimensionalized using suitable transformations, further reduced to non-similar form using stream function formulation and solved by local non-similarity method with homotopy analysis method. The numerical computations are validated and verified by comparing with earlier published results and are found to be in good agreement.FindingsThe effects of varying the physical parameters such as Prandtl number, Schmidt number, Weissenberg number, thermophoresis parameter, Brownian motion parameter and buoyancy ratio parameter on velocity, temperature and species concentration are discussed and presented through graphs. The results explored that the velocity of shear thinning fluid is raised by increasing the Weissenberg number, while contrary response is seen for the shear thickening fluid. It is also found that heat transfer in Cattaneo–Christov heat conduction model is less than that in Fourier’s heat conduction model. Furthermore, the temperature and thermal boundary layer thickness expand with the increase in thermophoresis and Brownian motion parameter, whereas nanoparticle volume fraction increases with increase in thermophoresis parameter, but reverse trend is observed with increase in Brownian motion parameter.Originality/valueThe present investigation is relatively original as very little research has been reported on Carreau nanofluids under the effect of Cattaneo–Christov heat flux model.

Evaluation of some mathematical models of solar radiation received by a ground collector

2016 ◽  
Vol 13 (4) ◽  
pp. 376-380 ◽  
Author(s):  
Abdelouahab Zaatri ◽  
Norelhouda Azzizi
Keyword(s):  
Solar Radiation ◽  
Solar Energy ◽  
Mathematical Models ◽  
Design Methodology ◽  
Energy Systems ◽  
Ground Level ◽  
Content Type ◽  
Design And Optimization ◽  
Best Fit ◽  
Complex Influence

Purpose Using modeling approaches, this paper aims to propose different mathematical models for estimating the different components of the solar radiation as well as the received solar energy by a collector. Design/methodology/approach In this article, the authors consider three mathematical models to estimate the solar radiation captured at ground level by a solar collector. These models are Capderou model, Liu & Jordan model and R.sun model. In the context of the design of experiments, we performed measurements of solar radiation received by a collector using a pyranometer. The obtained measurements were compared with the three mathematical models. Findings The comparison enabled the subsequent evaluation to determine the most appropriate model that best fit for our region. As a result, the Capderou model reveals to be the most suitable for our region. Originality/value Estimation of solar radiation at ground level (received by a collector) is of paramount importance for the design and optimization of solar energy systems. Nevertheless, many factors influence the amount of energy received by a collector situated at a ground, such as the longitude of the location, latitude, altitude, tilt collector orientation, temperature and humidity of the environment, wind speed, etc. Because of the complex influence of these parameters, the received solar radiation by the collector is a dynamical and a random process.

Heat Loss Analysis of Flamelets in Near-Limit Spread Over Solid Fuel Surfaces

2001 ◽  
Author(s):  
Robert Vance ◽  
Indrek S. Wichman
Keyword(s):  
Heat Loss ◽  
Solid Fuel ◽  
Flame Spread ◽  
Environmental Conditions ◽  
Flame Length ◽  
Heat Losses ◽  
Loss Analysis ◽  
Parabolic Shape ◽  
Flame Sheet ◽  
Surface Decomposition

Abstract The profile of a spreading flamelet is analyzed by examining the heat losses to surrounding surfaces. The study addresses the reasons why flamelets have shapes ranging from round hemispherical “caps” to flat “coin-like” discs. A parabolic shape profile is used for the thin flame sheet, which provides both flame length and flame curvature. A third parameter specifies the height of the flame from the surface beneath it. Radiation and conduction heat losses from the flame sheet are calculated for various flame shapes. Overall heat losses as well as heat losses to the surface beneath the flamelet are examined. Some of the heat “losses” are misnamed because they produce the necessary surface decomposition for subsequent gaseous flame fuel vapors. Strictly, then, “losses” do not contribute appreciably to the maintenance of the flame. Physical arguments are made to explain observed flame spread behavior and flame shapes in response to prevailing flow and environmental conditions.

Hybrid nanofluid flow and heat transfer past a vertical thin needle with prescribed surface heat flux

2019 ◽  
Vol 29 (12) ◽  
pp. 4875-4894 ◽  
Author(s):  
Iskandar Waini ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Heat Flux ◽  
Surface Heat ◽  
Dual Solutions ◽  
Hybrid Nanofluid ◽  
Nanofluid Flow ◽  
Needle Size ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose The purpose of this paper is to study the steady mixed convection hybrid nanofluid flow and heat transfer past a vertical thin needle with prescribed surface heat flux. Design/methodology/approach The governing partial differential equations are transformed into a set of ordinary differential equations by using a similarity transformation. The transformed equations are then solved numerically using the boundary value problem solver (bvp4c) in Matlab software. The features of the skin friction coefficient and the local Nusselt number as well as the velocity and temperature profiles for different values of the governing parameters are analyzed and discussed. Findings It is found that dual solutions exist for a certain range of the mixed convection parameter where its critical values decrease with the increasing of the copper (Cu) nanoparticle volume fractions and for the smaller needle size. It is also observed that the increasing of the copper (Cu) nanoparticle volume fractions and the decreasing of the needle size tend to enhance the skin friction coefficient and the local Nusselt number on the needle surface. A temporal stability analysis is performed to determine the stability of the dual solutions in the long run, and it is revealed that only one of them is stable, while the other is unstable. Originality/value The problem of hybrid nanofluid flow and heat transfer past a vertical thin needle with prescribed surface heat flux is the important originality of the present study where the dual solutions for the opposing flow are obtained.

scholarly journals Optimization of Geometric Parameters of Thermal Insulation of Pre-Insulated Double Pipes

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1012 ◽  
Author(s):  
Dorota Krawczyk ◽  
Tomasz Teleszewski
Keyword(s):  
Heat Flux ◽  
Heat Conduction ◽  
Cross Section ◽  
Thermal Insulation ◽  
Major Axis ◽  
Heat Losses ◽  
Sectional Area ◽  
Cross Sectional ◽  
Elliptical Shape ◽  
Half Axis

This paper presents the analysis of the heat conduction of pre-insulated double ducts and the optimization of the shape of thermal insulation by applying an elliptical shape. The shape of the cross-section of the thermal insulation is significantly affected by the thermal efficiency of double pre-insulated networks. The thickness of the insulation from the external side of the supply and return pipes affects the heat losses of the double pre-insulated pipes, while the distance between the supply and return pipes influences the heat flux exchanged between these ducts. An assumed elliptical shape with a ratio of the major axis to the minor half axis of an ellipse equaling 1.93 was compared to thermal circular insulation with the same cross-sectional area. All calculations were made using the boundary element method (BEM) using a proprietary computer program written in Fortran as part of the VIPSKILLS project.

Development and commissioning of FBG sensors for impact test of rock fall protective barrier

Sensor Review ◽  
2014 ◽  
Vol 34 (4) ◽  
pp. 343-348 ◽  
Author(s):  
Yongxing Guo ◽  
Dongsheng Zhang ◽  
Zude Zhou ◽  
Fangdong Zhu ◽  
Li Xiong
Keyword(s):  
Real Time ◽  
Detection System ◽  
Field Application ◽  
Elastic Structure ◽  
Dynamic Force ◽  
Optimized Design ◽  
Element Analysis ◽  
Content Type ◽  
Protective Barrier ◽  
Force Transducers

Purpose – This paper aims to present an effective sensing detection system based on fiber Bragg grating (FBG) sensing technology for protective barriers that have been effectively applied to intercept and stop rocks from falling onto railway tracks. . Determination of exact stress and deformation values during impact tests for key components of the protective barrier forms important criteria for quality control of these barriers. Monitoring changes in force along the protective barrier when deployed in field application allows for real-time disaster warning for collapse and falling rocks. Design/methodology/approach – In this paper, we propose a monitoring strategy for key components of a protective barrier. During performance tests, dynamic force and strain were measured for the steel strands and supporting I-beam, respectively. Design of a special elastic structure for the force transducer based on finite element analysis and tensile tests has been discussed here. Two types of FBG force transducers were manufactured based on the elastic structure. Four FBG force transducers and four FBG strain sensors were used for impact verification testing of a new rigid protective barrier with a design protection level of 25 KJ. Findings – Dynamic force and strain responses were obtained during an impact of free-falling block with a kinetic energy of 25 KJ. Originality/value – The FBG monitoring scheme can be extremely valuable for optimized design of the barrier and can provide real-time disaster warning in regions of collapse and falling rocks.

Sign in / Sign up

Export Citation Format

Share Document