Ultra-Low-Voltage 20-GHz Frequency Dividers Using Transformer Feedback in 0.18-$\mu$m CMOS Process

2008 ◽  
Vol 43 (10) ◽  
pp. 2293-2302 ◽  
Author(s):  
Hui Zheng ◽  
Howard C. Luong
Keyword(s):  
Low Voltage ◽  
Cmos Process ◽  
Frequency Dividers ◽  
Transformer Feedback

scholarly journals 0.5-V Frequency Dividers in Folded MCML Exploiting Forward Body Bias: Analysis and Comparison

Electronics ◽  
2021 ◽  
Vol 10 (12) ◽  
pp. 1383
Author(s):  
Francesco Centurelli ◽  
Giuseppe Scotti ◽  
Gaetano Palumbo
Keyword(s):  
Power Consumption ◽  
Low Voltage ◽  
Building Blocks ◽  
Frequency Divider ◽  
Cmos Process ◽  
Design Strategies ◽  
Frequency Dividers ◽  
Level Shifter ◽  
Forward Body Bias ◽  
Body Bias

Two frequency divider architectures in the Folded MOS Current Mode Logic which allow to operate at ultra-low voltage thanks to forward body bias are presented, analyzed, and compared. The first considered architecture exploits nType and pType divide-by-two building blocks (DIV2s) without level shifters, whereas the second one is based on the cascade of nType DIV2s with input level shifter. Both the architectures have been previously proposed by the same authors with higher supply voltages, but are able to work at a supply voltage as low as 0.5 V due to the threshold lowering allowed by forward body bias. For each architecture, analytical design strategies to optimize the divider under different operation scenarios are considered and a comparison among all the treated case studies is presented. Simulation results considering a commercial 28 nm FDSOI CMOS process are reported to confirm the advantages and features of the different architectures and design strategies. The analysis show that the use of the forward body bias allows to design frequency dividers which have the best efficiency. Moreover, we have found that the frequency divider architecture based on nType and pType DIV2s without level shifter provides always better performance both in terms of speed and power consumption approaching about 17 GHz of maximum operating frequency with less than 30 μW power consumption.

Analysis of 6T SRAM Cell in Different Technologies

2017 ◽  
Vol MCSP2017 (01) ◽  
pp. 7-10 ◽  
Author(s):  
Subhashree Rath ◽  
Siba Kumar Panda
Keyword(s):  
Low Power ◽  
Data Storage ◽  
Low Voltage ◽  
Random Access ◽  
Storage Device ◽  
Cmos Process ◽  
Process Technology ◽  
Digital Devices ◽  
Noise Margin ◽  
Sram Cell

Static random access memory (SRAM) is an important component of embedded cache memory of handheld digital devices. SRAM has become major data storage device due to its large storage density and less time to access. Exponential growth of low power digital devices has raised the demand of low voltage low power SRAM. This paper presents design and implementation of 6T SRAM cell in 180 nm, 90 nm and 45 nm standard CMOS process technology. The simulation has been done in Cadence Virtuoso environment. The performance analysis of SRAM cell has been evaluated in terms of delay, power and static noise margin (SNM).

scholarly journals Design Strategies and Architectures for Ultra-Low-Voltage Delta-Sigma ADCs

Electronics ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 1156
Author(s):  
Lorenzo Benvenuti ◽  
Alessandro Catania ◽  
Giuseppe Manfredini ◽  
Andrea Ria ◽  
Massimo Piotto ◽  
...  
Keyword(s):  
Low Voltage ◽  
Flicker Noise ◽  
Supply Voltage ◽  
Cmos Process ◽  
Clock Frequency ◽  
Design Environment ◽  
Ultra Low Power ◽  
Analog Cmos ◽  
Gain Error ◽  
Dc Gain

The design of ultra-low voltage analog CMOS integrated circuits requires ad hoc solutions to counteract the severe limitations introduced by the reduced voltage headroom. A popular approach is represented by inverter-based topologies, which however may suffer from reduced finite DC gain, thus limiting the accuracy and the resolutions of pivotal circuits like analog-to-digital converters. In this work, we discuss the effects of finite DC gain on ultra-low voltage ΔΣ modulators, focusing on the converter gain error. We propose an ultra-low voltage, ultra-low power, inverter-based ΔΣ modulator with reduced finite-DC-gain sensitivity. The modulator employs a two-stage, high DC-gain, switched-capacitor integrator that applies a correlated double sampling technique for offset cancellation and flicker noise reduction; it also makes use of an amplifier that implements a novel common-mode stabilization loop. The modulator was designed with the UMC 0.18 μm CMOS process to operate with a supply voltage of 0.3 V. It was validated by means of electrical simulations using the CadenceTM design environment. The achieved SNDR was 73 dB, with a bandwidth of 640 Hz, and a clock frequency of 164 kHz, consuming only 200.5 nW. It achieves a Schreier Figure of Merit of 168.1 dB. The proposed modulator is also able to work with lower supply voltages down to 0.15 V with the same resolution and a lower power consumption despite of a lower bandwidth. These characteristics make this design very appealing in sensor interfaces powered by energy harvesting sources.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

Design and Layout of a High-Performance PWM Control Class D Amplifiers IC Systems

2012 ◽  
Vol 203 ◽  
pp. 469-473
Author(s):  
Ruei Chang Chen ◽  
Shih Fong Lee
Keyword(s):  
Low Power ◽  
High Performance ◽  
Low Voltage ◽  
Design Flow ◽  
Total Power ◽  
Cmos Process ◽  
Low Power Circuits ◽  
Class D ◽  
Total Power Consumption ◽  
Power Circuits

This paper presents the design and implementation of a novel pulse width modulation control class D amplifiers chip. With high-performance, low-voltage, low-power and small area, these circuits are employed in portable electronic systems, such as the low-power circuits, wireless communication and high-frequency circuit systems. This class D chip followed the chip implementation center advanced design flow, and then was fabricated using Taiwan Semiconductor Manufacture Company 0.35-μm 2P4M mixed-signal CMOS process. The chip supply voltage is 3.3 V which can operate at a maximum frequency of 100 MHz. The total power consumption is 2.8307 mW, and the chip area size is 1.1497×1.1497 mm2. Finally, the class D chip was tested and the experimental results are discussed. From the excellent performance of the chip verified that it can be applied to audio amplifiers, low-power circuits, etc.

scholarly journals A 219-µW ultra-low power low-noise amplifier for IEEE 802.15.4 based battery powered, portable, wearable IoT applications

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
S. Chrisben Gladson ◽  
Adith Hari Narayana ◽  
V. Thenmozhi ◽  
M. Bhaskar
Keyword(s):  
Low Power ◽  
Ieee 802.15.4 ◽  
Low Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Process Technology ◽  
Ultra Low Power ◽  
Power Mode ◽  
Noise Amplifier

AbstractDue to the increased processing data rates, which is required in applications such as fifth-generation (5G) wireless networks, the battery power will discharge rapidly. Hence, there is a need for the design of novel circuit topologies to cater the demand of ultra-low voltage and low power operation. In this paper, a low-noise amplifier (LNA) operating at ultra-low voltage is proposed to address the demands of battery-powered communication devices. The LNA dual shunt peaking and has two modes of operation. In low-power mode (Mode-I), the LNA achieves a high gain ($$S21$$ S 21 ) of 18.87 dB, minimum noise figure ($${NF}_{min.}$$ NF m i n . ) of 2.5 dB in the − 3 dB frequency range of 2.3–2.9 GHz, and third-order intercept point (IIP3) of − 7.9dBm when operating at 0.6 V supply. In high-power mode (Mode-II), the achieved gain, NF, and IIP3 are 21.36 dB, 2.3 dB, and 13.78dBm respectively when operating at 1 V supply. The proposed LNA is implemented in UMC 180 nm CMOS process technology with a core area of $$0.40{\mathrm{ mm}}^{2}$$ 0.40 mm 2 and the post-layout validation is performed using Cadence SpectreRF circuit simulator.

scholarly journals Design of a Low Voltage Schmitt Trigger in 0.18 um CMOS Process With Tunable Hysteresis

2013 ◽  
Vol 7 (4) ◽  
Author(s):  
Haroon Rashid ◽  
Md. Mamun ◽  
Md. Syedul Amin ◽  
Hafizah Husain
Keyword(s):  
Low Voltage ◽  
Schmitt Trigger ◽  
Cmos Process
Sign in / Sign up

Export Citation Format

Share Document