scholarly journals IMPACT FORCE RECONSTRUCTION USING WAVELET DECONVOLUTION TECHNIQUE

2018 ◽  
Vol 8 (1) ◽  
pp. 53-66
Author(s):  
Hai Tran ◽  
Hirotsugu Inoue
Keyword(s):  
Finite Element ◽  
Structural Model ◽  
Impact Force ◽  
Haar Wavelet ◽  
Reconstruction Process ◽  
Impact Forces ◽  
Deconvolution Technique ◽  
Force Reconstruction ◽  
The Impact ◽  
Wavelet Technique

Reconstruction or deconvolution of impact force history from corresponding impact responses such as strain, acceleration, and displacement has been considered as a useful indirect method for measuring the impact force. However, due to the ill-posed nature of deconvolution problem, impact force is often inaccurately and unstably reconstructed. This paper introduces and applies the deconvolution technique using wavelets as a robust method for reconstructing impact force with the advantageous properties of wavelets. First, an analytical process of impact force reconstruction by using the wavelet technique in terms of scaling and translating the Haar wavelet is formulated. The unknown impact force is represented by the expanded coefficients at different scales and shifts of Haar wavelet which is compactly supported in the time domain (finite in time). Then, based on the governing equation of impact force deconvolution, the reconstruction process of these expanded coefficients is formulated. Second, a structural model is built by finite element method to obtain impulse response function numerically. After that, the wavelet technique is applied to reconstruct the impact forces acting on the structure to verify its effectiveness. The comparisons between reconstructed forces and finite element analysis results demonstrate the success of the present technique in accurately reconstructing the numerical impact forces acting on the thin-walled column. These achievements show remarkable ability of the wavelet technique for reconstructing accurately any input forces.

scholarly journals Wavelet deconvolution technique for impact force reconstruction: mutual deconvolution approach

2021 ◽  
Vol 3 (SI2) ◽  
pp. first
Author(s):  
Hai Tran ◽  
Tat-Hien Le
Keyword(s):  
Indirect Method ◽  
Impact Force ◽  
Impulse Response Function ◽  
Reconstruction Process ◽  
Deconvolution Technique ◽  
Force Reconstruction ◽  
History Of ◽  
Ill Posed ◽  
And Shifts ◽  
Large Magnification

In the field of impact engineering, one of the most concerned issues is how to exactly know the history of impact force which often difficult or impossible to be measured directly. In reality, information of impact force apply to structure can be identified by means of indirect method from using information of corresponding output responses measured on structure. Namely, by using the output responses (caused by the unknown impact force) such as acceleration, displacement, or strain, etc. in cooperation with the impulse response function, the profile of unknown impact force can be rebuilt. A such indirect method is well known as impact force reconstruction or impact force deconvolution technique. Unfortunately, a simple deconvolution technique for reconstructing impact force has often encountered difficulty due to the ill-posed nature of inversion. Deconvolution technique thus often results in unexpected reconstruction of impact force with the influences of unavoidable errors which is often magnified to a large value in reconstructed result. This large magnification of errors dominates profile of desired impact force. Although there have been some regularization methods in order to improve this ill-posed problem so far, most of these regularizations are considered in the whole-time domain, and this may make the reconstruction inefficient and inaccurate because impact force is normally limited to some portions of impact duration. This work is concerned with the development of deconvolution technique using wavelets transform. Based on the advantages of wavelets (i.e., localized in time and the possibility to be analyzed at different scales and shifts), the mutual reconstruction process is proposed and formulated by considering different scales of wavelets. The experiment is conducted to verify the proposed technique. Results demonstrated the robustness of the present technique when reconstructing impact force with more stability and higher accuracy.

The Effects of Upstream Flexible Barrier on the Debris Flow Entrainment and Impact Dynamics on a Terminal Barrier

2021 ◽  
Author(s):  
Hervé Vicari ◽  
C.W.W. Ng ◽  
Steinar Nordal ◽  
Vikas Thakur ◽  
W.A. Roanga K. De Silva ◽  
...  
Keyword(s):  
Debris Flow ◽  
Debris Flows ◽  
Impact Force ◽  
Dynamic Pressure ◽  
Pressure Coefficient ◽  
Flexible Barrier ◽  
Impact Forces ◽  
Flexible Barriers ◽  
The Impact ◽  
Bed Entrainment

The destructive nature of debris flows is mainly caused by flow bulking from entrainment of an erodible channel bed. To arrest these flows, multiple flexible barriers are commonly installed along the predicted flow path. Despite the importance of an erodible bed, its effects are generally ignored when designing barriers. In this study, three unique experiments were carried out in a 28 m-long flume to investigate the impact of a debris flow on both single and dual flexible barriers installed in a channel with a 6 m-long erodible soil bed. Initial debris volumes of 2.5 m<sup>3</sup> and 6 m<sup>3</sup> were modelled. For the test setting adopted, a small upstream flexible barrier before the erodible bed separates the flow into several surges via overflow. The smaller surges reduce bed entrainment by 70% and impact force on the terminal barrier by 94% compared to the case without an upstream flexible barrier. However, debris overflowing the deformed flexible upstream barrier induces a centrifugal force that results in a dynamic pressure coefficient that is up to 2.2 times higher than those recommended in guidelines. This suggests that although compact upstream flexible barriers can be effective for controlling bed entrainment, they should be carefully designed to withstand higher impact forces.

Revealing Mechanical Strength of Nanopores Using Atomic Finite Element Techniques

2018 ◽  
Vol 934 ◽  
pp. 24-29
Author(s):  
Prapasiri Pongprayoon ◽  
Attaphon Chaimanatsakun
Keyword(s):  
Mechanical Properties ◽  
Finite Element Method ◽  
Finite Element ◽  
Fluid Flow ◽  
Mechanical Strength ◽  
Impact Force ◽  
Pore Surface ◽  
Vertical Rectangle ◽  
The Impact ◽  
Graphene Nanopore

Graphene nanopore has been widely employed in nanofilter or nanopore devices due to its outstanding properties. The understanding of its mechanical properties at nanoscale is crucial for device improvement. In this work, the mechanical properties of graphene nanopore is thus investigated using atomistic finite element method (AFEM). Four graphene models with different pore shapes (circular (CR), horizontal rectangle (RH), and vertical rectangle (RV)) in sub-nm size which could be successfully fabricated experimentally have been studied here. The force normal to a pore surface is applied to mimic the impact force due to a fluid flow. Increasing pore size results in the reduction in its strength. Comparing among different pore shapes with comparable sizes, the order of pore strength is CR>RH>RV>SQ. In addition, we observe that the direction of pore alignment and geometries of pore edge also play a key role in mechanical strength of nanopores.

scholarly journals Comparison of branded rugby headguards on their effectiveness in reducing impact on the head

2018 ◽  
Vol 4 (1) ◽  
pp. e000361 ◽  
Author(s):  
Erin R A Frizzell ◽  
Graham P Arnold ◽  
Weijie Wang ◽  
Rami J Abboud ◽  
Tim S Drew
Keyword(s):  
Impact Force ◽  
Linear Acceleration ◽  
Baseline Measurement ◽  
Peak Acceleration ◽  
Impact Forces ◽  
Impact Attenuation ◽  
The Mean ◽  
Force Reduction ◽  
The Right ◽  
The Impact

AimTo compare the available brands of rugby headguards and evaluate their impact attenuation properties at various locations on the cranium, with regard to concussion prevention.MethodsSeven different branded headguards were fitted onto a rigid headform and drop-tested in three different positions. An accelerometer measured the linear acceleration the headform experienced on impact with the ground. Each test involved dropping the headform from a height that generated 103.8 g on average when bare, which is the closest acceleration to the upper limit of the concussion threshold of 100 g. A mean peak acceleration for each drop position was calculated and compared with the bare baseline measurement.ResultsEach headguard demonstrated a significant decrease in the mean peak acceleration from the baseline value (all p≤0.01). Overall the Canterbury Ventilator was the most effective headguard, decreasing the impact force on average by 47%. The least effective was the XBlades Elite headguard, averaging a force reduction of 27%. In five of the seven headguards, the right side of the headwear was the most effective at reducing impact force.ConclusionOverall, the results indicate that it would be beneficial to wear a headguard during rugby in order to reduce the impact forces involved in head collisions. There was also a clear difference in performance between the tested brands, establishing the Canterbury headguard as the most effective. However, only one model of headguard from each brand was tested, so further research evaluating all other models should be considered.

scholarly journals STUDY ON IMPACT FORCES OF THE UNDERWATER CAVITY PROJECTILE

2016 ◽  
Vol 54 (6) ◽  
pp. 797
Author(s):  
Nguyen Thai Dung ◽  
Nguyen Duc Thuyen
Keyword(s):  
Drag Force ◽  
Impact Force ◽  
Center Of Mass ◽  
Forward Direction ◽  
Cavity Wall ◽  
Impact Point ◽  
Impact Forces ◽  
Underwater Projectile ◽  
The Impact ◽  
Cavity Effect

The motion of the underwater projectile with cavity effect including two motions: the projectile moves in the forward direction, center of mass of the projectile rotation around its nose makes tail of the projectile impacts on the cavity wall. According to, the impact forces occur, they include the drag force at its none, the impact force at impact point. The paper studies the forces occur on during motion of the underwater cavity projectile. Added, this paper considers the effect of the length and distributive projectile to the magnitude of impact force and the drag force of the underwater cavity projectile.

A system for simulating the kinematics and measuring the impact force from riding whips used in Thoroughbred horseracing

2020 ◽  
pp. 175433712098062
Author(s):  
John W Bridge ◽  
Kaleb M Dempsey ◽  
Kayla M Danicki ◽  
Robin L Angotti ◽  
Alan K Kwiatkowski ◽  
...  
Keyword(s):  
Impact Force ◽  
Dynamic Force ◽  
Horse Racing ◽  
Testing Device ◽  
Shaft Length ◽  
Impact Forces ◽  
The Face ◽  
Flap Design ◽  
Arm Motion ◽  
The Impact

Thirty horse racing whips of four different designs were tested to measure dynamic impact force and compared using a specially designed mechanical testing device to simulate the whipping action of a jockey during racing. The whips tested included designs used in Thoroughbred horse racing in North America, which meet the design criteria established by the Association of Racing Commissioners International (ARCI) model rules, as well as the most common whip used in British horse racing. The objective of the device was to allow comparisons to be made between peak impact loads resulting from different whip designs. A high peak dynamic force on a horse’s shoulder or hind quarter may result in injuries, such as welts. The testing device contains a planar three-bar, open mechanical linkage loaded by torsion springs to model the arm motion of a jockey. The whip strikes a flat plate covered by an elastomeric pad. The energy input is replicated during the simulated impact. A single axis dynamic load cell under the loading plate and three single-turn precision potentiometers located at each joint of the three-arm mechanical system measure impact forces and relative angular positions, respectively. Force measurements are compared from the face of each whip and the edge or seam where applicable. In addition to the flap design, other physical differences between whip designs included mass, shaft length, shaft stiffness, flap cushion thickness/compression factor, flap surface area, and flap seam area. Statistically significant impact force differences were found between flap face and flap seam impact orientations, with higher impact forces delivered by the flap face. Significant differences were also found in impact forces between the three whip styles with seams.

scholarly journals Study on the Impact Resistance of Metal Flexible Net to Rock fall

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Gaosheng Wang ◽  
Yunhou Sun ◽  
Ao Zhang ◽  
Lei Zheng ◽  
Yuzheng Lv ◽  
...  
Keyword(s):  
Finite Element ◽  
Impact Force ◽  
Impact Resistance ◽  
Time History ◽  
Rock Fall ◽  
Fe Model ◽  
Element Analysis ◽  
Inclination Angles ◽  
Fall Protection ◽  
The Impact

Based on experiments and finite element analysis, the impact resistance of metal flexible net was studied, which can provide reference for the application of metal flexible net in rock fall protection. The oblique (30 degrees) impact experiment of metal flexible net was carried out, the corresponding finite element (FE) to the experiment was established, and the FE model was verified by simulation results to the experimental tests from three aspects: the deformation characteristics of metal flexible net, the time history curves of impact force on supporting ropes, and the maximum instantaneous impact force on supporting ropes. The FE models of metal flexible nets with inclination angles of 0, 15, 30, 45, 60, and 75 degrees were established, and the impact resistance of metal flexible nets with different inclination angles was analyzed. The research shows that the metal flexible net with proper inclination can bounce the impact rock fall out of the safe area and prevent rock fall falling on the metal flexible net, thus realizing the self-cleaning function. When the inclination angle of the metal flexible net is 15, 30, and 45 degrees, respectively, the bounce effect after impact is better, the remaining height is improved, the protection width is improved obviously, and the impact force is reduced. Herein, the impact force of rock fall decreases most obviously at 45 degrees inclination, and the protective performance is relatively good.

scholarly journals Debris Flow Damage Assessment by Considering Debris Flow Direction and Direction Angle of Structure in South Korea

Water ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 328 ◽  
Author(s):  
Dong Nam ◽  
Man-Il Kim ◽  
Dong Kang ◽  
Byung Kim
Keyword(s):  
South Korea ◽  
Debris Flow ◽  
Debris Flows ◽  
Impact Force ◽  
Mountainous Areas ◽  
Mountainous Regions ◽  
Impact Forces ◽  
The Impact

Recently, human and property damages have often occurred due to various reasons—such as landslides, debris flow, and other sediment-related disasters—which are also caused by regional torrential rain resulting from climate change and reckless development of mountainous areas. Debris flows mainly occur in mountainous areas near urban living communities and often cause direct damages. In general, debris flows containing soil, rock fragments, and driftwood temporarily travel down to lower parts along with a mountain torrent. However, debris flows are also often reported to stream down from the point where a slope failure or a landslide occurs in a mountain directly to its lower parts. The impact of those debris flows is one of the main factors that cause serious damage to structures. To mitigate such damage of debris flows, a quantitative assessment of the impact force is thus required. Moreover, technologies to evaluate disaster prevention facilities and structures at disaster-prone regions are needed. This study developed two models to quantitatively analyze the damages caused by debris flows on structures: Type-1 model for calculating the impact force, which reflected the flow characteristics of debris flows and the Type-2 model, which calculated the impact force based on the topographical characteristics of mountainous regions. Using RAMMS a debris flow runoff model, the impact forces assessed through Type-1 and Type-2 models were compared to check reliability. Using the assessed impact forces, the damage ratio of the structures was calculated and the amount of damage caused by debris flows on the structures was ultimately assessed. The results showed that the Type-1 model overestimated the impact force by 10% and the Type-2 model by 4% for Mt. Umyeon in Seoul, compared to the RAMMS model. In addition, the Type-1 model overestimated the impact force by 3% and Type-2 by 2% for Mt. Majeok in Chuncheon, South Korea.

scholarly journals Effective Formula for Impact Damping Ratio for Simulation of Earthquake-induced Structural Pounding

Geosciences ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 347 ◽  
Author(s):  
Seyed Mohammad Khatami ◽  
Hosein Naderpour ◽  
Rui Carneiro Barros ◽  
Anna Jakubczyk-Gałczyńska ◽  
Robert Jankowski
Keyword(s):  
Kinetic Energy ◽  
Impact Force ◽  
Damping Ratio ◽  
Dissipated Energy ◽  
Force Model ◽  
Single Collision ◽  
Structural Pounding ◽  
Impact Forces ◽  
The Impact ◽  
Impact Damping

Structural pounding during earthquakes may cause substantial damage to colliding structures. The phenomenon is numerically studied using different models of collisions. The aim of the present paper is to propose an effective formula for the impact damping ratio, as a parameter of the impact force model used to study different problems of structural pounding under seismic excitations. Its accuracy has been verified by four various approaches. Firstly, for the case of collisions between two structural elements, the dissipated energy during impact has been compared to the loss of kinetic energy. In the second stage of verifications, the peak impact forces during single collision have been analyzed. Then, the accuracy of different equations have been verified by comparing the impact force time histories for the situation when a concrete ball is dropped on a rigid concrete surface. Finally, pounding between two structures during earthquakes has been studied. The results of the analysis focused on comparison between dissipated and kinetic energy show relatively low errors between calculated and assumed values of the coefficient of restitution when the proposed equation is used. In addition, the results of the comparison between experimentally and numerically determined peak impact forces during single collision confirm the effectiveness of the approach. The same conclusion has been obtained for the whole impact time history for collision between a ball and a rigid surface. Finally, the results of the comparative analysis, conducted for pounding between two structures during an earthquake, confirm the simulation accuracy when the proposed approach is used. The above conclusions indicate that the proposed formula for impact damping ratio, as a parameter of impact force model for simulation of earthquake-induced structural pounding, is very effective and accurate in numerical simulations in the case of different scenarios.

Finite Element Analysis of a Single-Layer Reticulated Dome under Impact Loading

2010 ◽  
Vol 163-167 ◽  
pp. 327-331 ◽  
Author(s):  
Liang Zheng ◽  
Zhi Hua Chen
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Impact Force ◽  
Impact Load ◽  
Residual Deformation ◽  
Time History ◽  
Single Layer ◽  
Element Analysis ◽  
Deformation Stage ◽  
The Impact

Finite element model of both the single-layer Schwedler reticulated dome with the span of 50m and a Cuboid impactor were developed, incorporating ANSYS/LS-DYNA. PLASTIC_KINEMATIC (MAT_003) material model which takes stain rate into account was used to simulate steel under impact load. The automatic point to surface contact (NODES TO SURFACE) was applied between the dome and impact block. Three stages of time history curve of the impact force on the apex of the single-layer Scheduler reticulated dome including the impact stage, stable stalemate stage, the decaying stage were generalized according to its dynamic response. It must be pointed out that the peak of the impact force of the single-layer reticulated dome increase with the increase of the weight and the velocity of the impact block, but the change of the velocity of the impact block is more sensitive than the change of weight of the impact block for the effect of the peak of the impact force, and a platform value of the impact force of the single-layer reticulated dome change near a certain value, and the duration time of the impact gradually increase. Then four stages of time history curve of the impact displacement were proposed according to the dynamic response of impact on the apex of the single-layer reticulated dome based on numerical analysis. Four stages include in elastic deformation stage, plastic deformation stage, elastic rebound stage, free vibration stage in the position of the residual deformation.

Sign in / Sign up

Export Citation Format

Share Document