A Greenwood-Williamson Model of Small-Scale Friction

2005 ◽  
Vol 74 (1) ◽  
pp. 31-40 ◽  
Author(s):  
Reese E. Jones
Keyword(s):  
Numerical Method ◽  
Recursion Formula ◽  
Three Dimensional ◽  
Interfacial Friction ◽  
Small Scale ◽  
Analytical Estimate ◽  
Normal Loading ◽  
Proposed Model ◽  
Loading Case ◽  
Transition Length

A Greenwood and Williamson based model for interfacial friction is presented that incorporates the presliding transition phenomenon that can significantly affect small devices. This work builds on previous similar models by developing: an analytical estimate of the transition length in terms of material and surface parameters, a general recursion formula for the case of slip in one direction with multiple reversals and constant normal loading, and a numerical method for the general three-dimensional loading case. In addition, the proposed model is developed within a plasticity-like framework and is shown to have qualitative similarities with published experimental observations. A number of model problems illustrate the response of the proposed model to various loading conditions.

scholarly journals A Multidimensional and Multiscale Model for Pressure Analysis in a Reservoir-Pipe-Valve System

2018 ◽  
Author(s):  
Feng Jie Zheng ◽  
Fu Zheng Qu ◽  
Xue Guan Song
Keyword(s):  
Pressure Fluctuation ◽  
Large Scale ◽  
Three Dimensional ◽  
Industrial Process ◽  
Multiscale Model ◽  
Computational Time ◽  
Small Scale ◽  
Cfd Model ◽  
Computationally Efficient ◽  
Proposed Model

Reservoir-pipe-valve (RPV) systems are widely used in many industrial process. The pressure in an RPV system plays an important role in the safe operation of the system, especially during the sudden operation such as rapid valve opening/closing. To investigate the pressure especially the pressure fluctuation in an RPV system, a multidimensional and multiscale model combining the method of characteristics (MOC) and computational fluid dynamics (CFD) method is proposed. In the model, the reservoir is modeled by a zero-dimensional virtual point, the pipe is modeled by a one-dimensional MOC, and the valve is modeled by a three-dimensional CFD model. An interface model is used to connect the multidimensional and multiscale model. Based on the model, a transient simulation of the turbulent flow in an RPV system is conducted, in which not only the pressure fluctuation in the pipe but also the detailed pressure distribution in the valve are obtained. The results show that the proposed model is in good agreement with the full CFD model in both large-scale and small-scale spaces. Moreover, the proposed model is more computationally efficient than the CFD model, which provides a feasibility in the analysis of complex RPV system within an affordable computational time.

scholarly journals A Multidimensional and Multiscale Model for Pressure Analysis in a Reservoir-Pipe-Valve System

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Feng Jie Zheng ◽  
Chao Yong Zong ◽  
William Dempster ◽  
Fu Zheng Qu ◽  
Xue Guan Song
Keyword(s):  
Large Scale ◽  
Pressure Fluctuations ◽  
Three Dimensional ◽  
Multiscale Model ◽  
Computational Time ◽  
Small Scale ◽  
Dimensional System ◽  
Cfd Model ◽  
Computationally Efficient ◽  
Proposed Model

Reservoir-pipe-valve (RPV) systems are widely used in many industrial processes. The pressure in an RPV system plays an important role in the safe operation of the system, especially during the sudden operations such as rapid valve opening or closing. To investigate the pressure response, with particular interest in the pressure fluctuations in an RPV system, a multidimensional and multiscale model combining the method of characteristics (MOC) and computational fluid dynamics (CFD) method is proposed. In the model, the reservoir is modeled as a zero-dimensional virtual point, the pipe is modeled as a one-dimensional system using the MOC, and the valve is modeled using a three-dimensional CFD model. An interface model is used to connect the multidimensional and multiscale model. Based on the model, a transient simulation of the turbulent flow in an RPV system is conducted in which not only the pressure fluctuation in the pipe but also the detailed pressure distribution in the valve is obtained. The results show that the proposed model is in good agreement when compared with a high fidelity CFD model used to represent both large-scale and small-scale spaces. As expected, the proposed model is significantly more computationally efficient than the CFD model. This demonstrates the feasibility of analyzing complex RPV systems within an affordable computational time.

scholarly journals THREE-DIMENSIONAL SIMULATION OF A SMALL-SCALE ELECTRODIALYSIS PROCESS FOR DOMESTIC USE

2020 ◽  
Vol 14 (2) ◽  
pp. 83-96
Author(s):  
Noureddine Bensedira ◽  
Mohammed-Salah Aggoune ◽  
Mabrouk Chabane ◽  
Said Drid
Keyword(s):  
Fluid Velocity ◽  
Three Dimensional ◽  
Ionic Transport ◽  
Ionic Concentration ◽  
Ion Concentration ◽  
Small Scale ◽  
Three Dimensional Modeling ◽  
Proposed Model ◽  
Domestic Use ◽  
Dimensional Simulation

The hydrodynamic by MHD driving force and ionic transport characteristics of an electrolytic solution in a small-scale electrodialysis process are taken into account in this new approach. A three-Dimensional modeling and simulation of coupling Magnetohydrodynamic-Ionic transport are carried out. The numerical values and the effects of applied voltage and magnetic induction on the fluid velocity and ionic concentration of species present in the solution are displayed graphically. The results show that a high decrease of ion concentration is achieved and suggest that the proposed model which has no moving parts can be practically implemented.

Simulating Compliant Crease Origami With a Bar and Hinge Model

2019 ◽  
Author(s):  
Yi Zhu ◽  
Evgueni T. Filipov
Keyword(s):  
Three Dimensional ◽  
Small Scale ◽  
Spring Stiffness ◽  
Mechanical Behaviors ◽  
Proposed Model ◽  
Plate Models ◽  
Modeling Techniques ◽  
Rigid Model ◽  
Stiffness Characteristics ◽  
Hinge Model

Abstract Small-scale origami inspired assemblages are usually made with soft compliant plates to serve as creases because it is difficult to fabricate real hinges at those scales. In most conventional origami modeling techniques, these soft and compliant creases are usually neglected and simplified as concentrated rotational springs. Such simplification does not capture the three dimensional geometry correctly and also neglects torsional and extensional deformations of the compliant creases. These deformations could be significant for determining advanced mechanical behaviors of the origami such as bistablity and multistablity. In this paper an improved formulation of a simple bar and hinge model is proposed to capture the geometry and flexibility of compliant creases. Equations for assigning bar areas and spring stiffness are derived based on the theoretical plane stress plate models and the pseudo-rigid model. These equations are next verified against finite element simulations for both infinitesimal stiffness and large deformation stiffness. It is found that the proposed model can predict stiffness characteristics of compliant crease origami relatively well. Furthermore, two examples are used to demonstrate the efficiency and capability of the proposed model.

Extrusion-Based 3D Printing for Pharmaceuticals: Contemporary Research and Applications

2019 ◽  
Vol 24 (42) ◽  
pp. 4991-5008 ◽  
Author(s):  
Mohammed S. Algahtani ◽  
Abdul Aleem Mohammed ◽  
Javed Ahmad
Keyword(s):  
Cosmetic Surgery ◽  
Fused Deposition Modeling ◽  
Personalised Medicine ◽  
Organ Transplant ◽  
Three Dimensional ◽  
Dosage Forms ◽  
Release Profile ◽  
Small Scale ◽  
Drug Release Profile ◽  
Fused Deposition

Three-dimensional printing (3DP) has a significant impact on organ transplant, cosmetic surgery, surgical planning, prosthetics and other medical fields. Recently, 3 DP attracted the attention as a promising method for the production of small-scale drug production. The knowledge expansion about the population differences in metabolism and genetics grows the need for personalised medicine substantially. In personalised medicine, the patient receives a tailored dose and the release profile is based on his pharmacokinetics data. 3 DP is expected to be one of the leading solutions for the personalisation of the drug dispensing. This technology can fabricate a drug-device with complicated geometries and fillings to obtain the needed drug release profile. The extrusionbased 3 DP is the most explored method for investigating the feasibility of the technology to produce a novel dosage form with properties that are difficult to achieve using the conventional industrial methods. Extrusionbased 3 DP is divided into two techniques, the semi-solid extrusion (SSE) and the fused deposition modeling (FDM). This review aims to explain the extrusion principles behind the two techniques and discuss their capabilities to fabricate novel dosage forms. The advantages and limitations observed through the application of SSE and FDM for fabrication of drug dosage forms were discussed in this review. Further exploration and development are required to implement this technology in the healthcare frontline for more effective and personalised treatment.

scholarly journals Quantification of Measurement and Model Effects in Monopile Foundation Scour Protection Experiments

2021 ◽  
Vol 9 (6) ◽  
pp. 585
Author(s):  
Minghao Wu ◽  
Leen De Vos ◽  
Carlos Emilio Arboleda Chavez ◽  
Vasiliki Stratigaki ◽  
Maximilian Streicher ◽  
...  
Keyword(s):  
Standard Deviation ◽  
Flow Field ◽  
Three Dimensional ◽  
Small Scale ◽  
Maximum Wave Height ◽  
Chaotic Flow ◽  
The Mean ◽  
Scour Protection ◽  
Damage Number ◽  
Measurement Effects

The present work introduces an analysis of the measurement and model effects that exist in monopile scour protection experiments with repeated small scale tests. The damage erosion is calculated using the three dimensional global damage number S3D and subarea damage number S3D,i. Results show that the standard deviation of the global damage number σ(S3D)=0.257 and is approximately 20% of the mean S3D, and the standard deviation of the subarea damage number σ(S3D,i)=0.42 which can be up to 33% of the mean S3D. The irreproducible maximum wave height, chaotic flow field and non-repeatable armour layer construction are regarded as the main reasons for the occurrence of strong model effects. The measurement effects are limited to σ(S3D)=0.039 and σ(S3D,i)=0.083, which are minor compared to the model effects.

scholarly journals The time domain numerical method of three-dimensional conductors including radiation with lumped parameter circuit

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Souma Jinno ◽  
Shuji Kitora ◽  
Hiroshi Toki ◽  
Masayuki Abe
Keyword(s):  
Numerical Method ◽  
Time Domain ◽  
Maxwell Equations ◽  
Three Dimensional ◽  
New Formalism ◽  
Vector Potentials ◽  
Lumped Parameter ◽  
Radiation Theory ◽  
Stable Solutions ◽  
The Time Domain

AbstractWe formulate a numerical method on the transmission and radiation theory of three-dimensional conductors starting from the Maxwell equations in the time domain. We include the delay effect in the integral equations for the scalar and vector potentials rigorously, which is vital to obtain numerically stable solutions for transmission and radiation phenomena in conductors. We provide a formalism to connect the conductors to any passive lumped-parameter circuits. We show one example of numerical calculations, demonstrating that the new formalism provides stable solutions to the transmission and radiation phenomena.

scholarly journals A Fast Two-Dimensional Numerical Method for the Wake Simulation of a Vertical Axis Wind Turbine

Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 49
Author(s):  
Zheng Yuan ◽  
Jin Jiang ◽  
Jun Zang ◽  
Qihu Sheng ◽  
Ke Sun ◽  
...  
Keyword(s):  
Velocity Distribution ◽  
Numerical Method ◽  
Three Dimensional ◽  
Particle Method ◽  
Vortex Method ◽  
Vertical Axis ◽  
Two Dimensional ◽  
Vertical Axis Wind Turbine ◽  
Wake Effect ◽  
Array Design

In the array design of the vertical axis wind turbines (VAWT), the wake effect of the upstream VAWT on the downstream VAWT needs to be considered. In order to simulate the velocity distribution of a VAWT wake rapidly, a new two-dimensional numerical method is proposed, which can make the array design easier and faster. In this new approach, the finite vortex method and vortex particle method are combined to simulate the generation and evolution of the vortex, respectively, the fast multipole method (FMM) is used to accelerate the calculation. Based on a characteristic of the VAWT wake, that is, the velocity distribution can be fitted into a power-law function, a new correction model is introduced to correct the three-dimensional effect of the VAWT wake. Finally, the simulation results can be approximated to the published experimental results in the first-order. As a new numerical method to simulate the complex VAWT wake, this paper proves the feasibility of the method and makes a preliminary validation. This method is not used to simulate the complex three-dimensional turbulent evolution but to simulate the velocity distribution quickly and relatively accurately, which meets the requirement for rapid simulation in the preliminary array design.

scholarly journals Experimental and Numerical Investigation about Small Clearance Journal Bearings under Static Load Conditions

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Carlo Alberto Niccolini Marmont Du Haut Champ ◽  
Fabrizio Stefani ◽  
Paolo Silvestri
Keyword(s):  
Three Dimensional ◽  
Journal Bearings ◽  
Radial Clearance ◽  
Small Scale ◽  
Test Rig ◽  
Small Clearance ◽  
Dimensional Simulation ◽  
Dynamic Loading Conditions ◽  
Static And Dynamic Loading ◽  
Good Agreement

The aim of the present research is to characterize both experimentally and numerically journal bearings with low radial clearances for rotors in small-scale applications (e.g., microgas turbines); their diameter is in the order of ten millimetres, leading to very small dimensional clearances when the typical relative ones (order of 1/1000) are employed; investigating this particular class of journal bearings under static and dynamic loading conditions represents something unexplored. To this goal, a suitable test rig was designed and the performance of its bearings was investigated under steady load. For the sake of comparison, numerical simulations of the lubrication were also performed by means of a simplified model. The original test rig adopted is a commercial rotor kit (RK), but substantial modifications were carried out in order to allow significant measurements. Indeed, the relative radial clearance of RK4 RK bearings is about 2/100, while it is around 1/1000 in industrial bearings. Therefore, the same original RK bearings are employed in this new test rig, but a new shaft was designed to reduce their original clearance. The new custom shaft allows to study bearing behaviour for different clearances, since it is equipped with interchangeable journals. Experimental data obtained by this test rig are then compared with further results of more sophisticated simulations. They were carried out by means of an in-house developed finite element (FEM) code, suitable for thermoelasto-hydrodynamic (TEHD) analysis of journal bearings both in static and dynamic conditions. In this paper, bearing static performances are studied to assess the reliability of the experimental journal location predictions by comparing them with the ones coming from already validated numerical codes. Such comparisons are presented both for large and small clearance bearings of original and modified RKs, respectively. Good agreement is found only for the modified RK equipped with small clearance bearings (relative radial clearance 8/1000), as expected. In comparison with two-dimensional lubrication analysis, three-dimensional simulation improves prediction of journal location and correlation with experimental results.

scholarly journals Nonlinear effects of locally heterogeneous hydraulic conductivity fields on regional stream–aquifer exchanges

2015 ◽  
Vol 19 (11) ◽  
pp. 4531-4545 ◽  
Author(s):  
J. Zhu ◽  
C. L. Winter ◽  
Z. Wang
Keyword(s):  
Groundwater Flow ◽  
Effective Conductivity ◽  
Model Simulation ◽  
Three Dimensional ◽  
Small Scale ◽  
Heihe River ◽  
Effective Parameters ◽  
Aquifer Systems ◽  
Basin Scale ◽  
Local Grid

Abstract. Computational experiments are performed to evaluate the effects of locally heterogeneous conductivity fields on regional exchanges of water between stream and aquifer systems in the Middle Heihe River basin (MHRB) of northwestern China. The effects are found to be nonlinear in the sense that simulated discharges from aquifers to streams are systematically lower than discharges produced by a base model parameterized with relatively coarse effective conductivity. A similar, but weaker, effect is observed for stream leakage. The study is organized around three hypotheses: (H1) small-scale spatial variations of conductivity significantly affect regional exchanges of water between streams and aquifers in river basins, (H2) aggregating small-scale heterogeneities into regional effective parameters systematically biases estimates of stream–aquifer exchanges, and (H3) the biases result from slow paths in groundwater flow that emerge due to small-scale heterogeneities. The hypotheses are evaluated by comparing stream–aquifer fluxes produced by the base model to fluxes simulated using realizations of the MHRB characterized by local (grid-scale) heterogeneity. Levels of local heterogeneity are manipulated as control variables by adjusting coefficients of variation. All models are implemented using the MODFLOW (Modular Three-dimensional Finite-difference Groundwater Flow Model) simulation environment, and the PEST (parameter estimation) tool is used to calibrate effective conductivities defined over 16 zones within the MHRB. The effective parameters are also used as expected values to develop lognormally distributed conductivity (K) fields on local grid scales. Stream–aquifer exchanges are simulated with K fields at both scales and then compared. Results show that the effects of small-scale heterogeneities significantly influence exchanges with simulations based on local-scale heterogeneities always producing discharges that are less than those produced by the base model. Although aquifer heterogeneities are uncorrelated at local scales, they appear to induce coherent slow paths in groundwater fluxes that in turn reduce aquifer–stream exchanges. Since surface water–groundwater exchanges are critical hydrologic processes in basin-scale water budgets, these results also have implications for water resources management.

Sign in / Sign up

Export Citation Format

Share Document