The Effect of Proof Loading on the Fatigue Behavior of Open Link Chain

1992 ◽  
Vol 114 (1) ◽  
pp. 27-33 ◽  
Author(s):  
S. M. Tipton ◽  
G. J. Shoup
Keyword(s):  
Fatigue Life ◽  
Residual Stresses ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Strain Gages ◽  
Applied Loading ◽  
Heat Treated ◽  
Strength Tests ◽  
Neuber's Rule ◽  
Failure Site

Open link lifting chain is routinely proof loaded during manufacture. However, the effect of residual stresses imposed by this operation on the fatigue strength of the chain has not been quantitatively investigated. This paper discusses the results of constant amplitude fatigue tests on open link chain segments which have received proof loading at various levels. The chain was initially heat treated to relieve manufacturing residual stresses and then proof loaded at levels ranging from 0 to 82 percent of its break strength. Tests were performed at two different mean loads and four different load amplitudes. Failure site trends are noted as a function of applied loading and are correlated with results of a finite element stress analysis. Residual stresses are estimated using strains measured from strain gages placed at critical locations on individual links during the proof load operation. Residual stress estimates are used with standard fatigue damage parameters to estimate the fatigue life of the chain and predictions are compared to data. Proof loading was shown to substantially increase the fatigue life of the chain. Residual stresses can explain the increase in fatigue life. Neuber’s rule demonstrated the ability to model the data trends.

scholarly journals The Effect of Laser Peening without Coating on the Fatigue of a 6082-T6 Aluminum Alloy with a Curved Notch

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 728 ◽  
Author(s):  
Enrico Troiani ◽  
Nicola Zavatta
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Residual Stresses ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Element Model ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Laser Peening ◽  
Laser Peening Without Coating

Laser shock peening has established itself as an effective surface treatment to enhance the fatigue properties of metallic materials. Although a number of works have dealt with the formation of residual stresses, and their consequent effects on the fatigue behavior, the influence of material geometry on the peening process has not been widely addressed. In this paper, Laser Peening without Coating (LPwC) is applied at the surface of a notch in specimens made of a 6082-T6 aluminum alloy. The treated specimens are tested by three-point bending fatigue tests, and their fatigue life is compared to that of untreated samples with an identical geometry. The fatigue life of the treated specimens is found to be 1.7 to 3.3 times longer. Brinell hardness measurements evidence an increase in the surface hardness of about 50%, following the treatment. The material response to peening is modelled by a finite element model, and the compressive residual stresses are computed accordingly. Stresses as high as −210 MPa are present at the notch. The ratio between the notch curvature and the laser spot radius is proposed as a parameter to evaluate the influence of the notch.

EFFECT OF CERAMIC COATING THICKNESS ON RESIDUAL STRESS AND FATIGUE CHARACTERISTIC OF 1Cr-1Mo-0.25V STEEL

2002 ◽  
Vol 16 (01n02) ◽  
pp. 181-188 ◽  
Author(s):  
CHANG-MIN SUH ◽  
BYUNG-WON HWANG ◽  
KYUNG-RYUL KIM
Keyword(s):  
Residual Stress ◽  
Fatigue Crack ◽  
Fatigue Life ◽  
Residual Stresses ◽  
Coating Thickness ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Turbine Rotor ◽  
Fatigue Tests ◽  
Rotor Steel

To evaluate the effect of coatings on the fatigue behaviors of turbine rotor steel, TiN and TiAlN films were deposited on the 1Cr-1Mo-0.25V steels by arc-ion plating (AIP) method with and wihtout screen ion filter. The coating thickness were varied with 2.5 μm, 3.5 μm, and 5.0 μm. A Cu-K α beam source was used as a characteristic X-ray and the crystal plane of (422) was selected to evaluate the residual stresses. In order to clear the relationship between fatigue behavior and residual stress of specimen coated with TiN and TiAlN films, the fatigue tests of specimens with and without coating were carried out at room temperatures respectively. It is shown that the fatigue life of the coated specimen was longer than that of uncoated specimen. The compressive residual stresses on the coatings were higher, and the fatigue crack initiated at an inclusion in the substrate near bond interface. It is known that compressive residual stress caused by hard coating would retard the fatigue crack initiation on the specimen surface, and then led to fatigue strength and fatigue life increasing.

scholarly journals Influence of Shot Peening on the Isothermal Fatigue Behavior of the Gamma Titanium Aluminide Ti-48Al-2Cr-2Nb at 750 °C

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1083
Author(s):  
Christoph Breuner ◽  
Stefan Guth ◽  
Elias Gall ◽  
Radosław Swadźba ◽  
Jens Gibmeier ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Shot Peening ◽  
Elevated Temperatures ◽  
Stress Amplitude ◽  
Negative Impact ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Fatigue Tests ◽  
Positive Effects ◽  
Isothermal Fatigue

One possibility to improve the fatigue life and strength of metallic materials is shot peening. However, at elevated temperatures, the induced residual stresses may relax. To investigate the influence of shot peening on high-temperature fatigue behavior, isothermal fatigue tests were conducted on shot-peened and untreated samples of gamma TiAl 48-2-2 at 750 °C in air. The shot-peened material was characterized using EBSD, microhardness, and residual stress analyses. Shot peening leads to a significant increase in surface hardness and high compressive residual stresses near the surface. Both effects may have a positive influence on lifetime. However, it also leads to surface notches and tensile residual stresses in the bulk material with a negative impact on cyclic lifetime. During fully reversed uniaxial tension-compression fatigue tests (R = −1) at a stress amplitude of 260 MPa, the positive effects dominate, and the fatigue lifetime increases. At a lower stress amplitude of 230 MPa, the negative effect of internal tensile residual stresses dominates, and the lifetime decreases. Shot peening leads to a transition from surface to volume crack initiation if the surface is not damaged by the shots.

High-cycle fatigue tests of pretensioned concrete beams

PCI Journal ◽  
2022 ◽  
Vol 67 (1) ◽  
Author(s):  
Jörn Remitz ◽  
Martin Empelmann
Keyword(s):  
Fatigue Life ◽  
High Cycle Fatigue ◽  
Concrete Beams ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Design Methods ◽  
Test Results ◽  
Cycle Fatigue ◽  
Pretensioned Concrete ◽  
Current Design

Pretensioned concrete beams are widely used as bridge girders for simply supported bridges. Understanding the fatigue behavior of such beams is very important for design and construction to prevent fatigue failure. The fatigue behavior of pretensioned concrete beams is mainly influenced by the fatigue of the prestressing strands. The evaluation of previous test results from the literature indicated a reduced fatigue life in the long-life region compared with current design methods and specifications. Therefore, nine additional high-cycle fatigue tests were conducted on pretensioned concrete beams with strand stress ranges of about 100 MPa (14.5 ksi). The test results confirmed that current design methods and specifications overestimate the fatigue life of embedded strands in pretensioned concrete beams.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

On the Effect of Electrodischarge Drilling on the Fatigue Life of Inconel 718

2014 ◽  
Vol 891-892 ◽  
pp. 1451-1456
Author(s):  
Elena Bassoli ◽  
Andrea Baldini ◽  
Andrea Gatto ◽  
Antonio Strozzi ◽  
Lucia Denti
Keyword(s):  
Fatigue Life ◽  
Inconel 718 ◽  
Metal Cutting ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Aerospace Applications ◽  
Rotating Bending Fatigue ◽  
Cutting Operation ◽  
Rotating Bending ◽  
Superposition Effect

Difficult-to cut-materials are associated with premature tool failure, most likely in the case of complex geometries and this shapes. However, Nickel-based alloys are commonly used in high-temperature and aerospace applications, where thin deep holes are often required. Then, the only viable manufacturing solution relies on non-contact processes, like electrodischarge (ED) drilling. Morphology of ED machined surfaces is significantly different than obtained by metal-cutting operation and is known to jeopardize fatigue strength, but the extent needs to be gauged and related to the process parameters. Aim of the paper is to study the effect of holes (0.8 mm diameter, aspect ratio 10) produced by ED drilling on the fatigue life of Inconel 718. Rotating bending fatigue tests are carried out on specimens drilled under two ED setups, as well as with a traditional cutting tool. Specimens free from holes are fatigued under the same conditions for comparison. Based on previous studies, extremal ED parameters are selected, giving best surface finish versus highest productivity. S-N curves show that the ED process causes a decrease of the fatigue resistance with respect to traditional drilling, whereas the effect of different ED setups is negligible. Maximum productivity can thus be pursued with no threat to fatigue performance. The fatigue limit variation is quantified by using the superposition effect principle: ED drilling causes an increase of the stress concentration factor around 25% if compared to traditional drilling. The macroscopic fatigue behavior is integrated with a study of the effects of the different drilling processes in the micro-scale, by means of a microstructural and fractographic analysis.

High Cycle Fatigue Behavior of Recycled Additive Manufactured Electron Beam Melted Titanium Ti6Al4V

2020 ◽  
Author(s):  
Melody Mojib ◽  
Rishi Pahuja ◽  
M. Ramulu ◽  
Dwayne Arola
Keyword(s):  
Electron Beam ◽  
Fatigue Life ◽  
Rough Surface ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
High Strength ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Initiation And Propagation ◽  
Powder Recycling

Abstract Metal Additive Manufacturing (AM) has become a popular method for producing complex and unique geometries, especially gaining traction in the aerospace and medical industries. With the increase in adoption of AM and the high cost of powder, it is critical to understand the effects of powder recycling on part performance to move towards material qualification and certification of affordable printed components. Due to the limitations of the Electron Beam Melting (EBM) process, current as-printed components are susceptible to failure at limits far below wrought metals and further understanding of the material properties and fatigue life is required. In this study, a high strength Titanium alloy, Ti-6Al-4V, is recycled over time and used to print fatigue specimens using the EBM process. Uniaxial High Cycle Fatigue tests have been performed on as-printed and polished cylindrical specimens and the locations of crack initiation and propagation have been determined through the use of a scanning electron microscope. This investigation has shown that the rough surface exterior is far more detrimental to performance life than the powder degradation occurring due to powder reuse. In addition, the effects of the rough surface exterior as a stress concentration is evaluated using the Arola-Ramulu. The following is a preliminary study of the effects powder recycling and surface treatments on EBM Ti-6Al4V fatigue life.

The Effects of Mechanical Properties on Fatigue Behavior of ECAPed AA7075

2016 ◽  
Vol 35 (3) ◽  
pp. 225-234 ◽  
Author(s):  
Hasan Kaya ◽  
Mehmet Uçar
Keyword(s):  
Electron Microscope ◽  
Fatigue Life ◽  
Fatigue Behavior ◽  
Optical Microscope ◽  
Fatigue Tests ◽  
Angular Pressing ◽  
Four Point Bending ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Hardness Values

AbstractIn this study, the effects of equal channel angular pressing (ECAP) on high-cycle fatigue and fatigue surface morphology of AA7075 have been investigated at a constant temperature (483 K) and the “C” route for four passes at ECAP process. ECAPed and as-received specimens were tested by four-point bending fatigue device. Fatigue tests were carried out by using 100, 120 and 140 MPa strength values. ECAPed specimens were characterized for each pass with optical microscope (OM), scanning electron microscope (SEM), energy-dispersive spectroscope (EDS), transmission electron microscope (TEM), selected area electron diffraction (SAED) and hardness measurements. Fracture surfaces of the specimens were also characterized with SEM. The results show that the highest hardness values (137 HV) and the best fatigue life (5.4 × 107for 100 MPa) were measured in ECAPed four-pass sample. For this reason hardness values and fatigue life were increased with increasing number of severe plastic deformation (SPD) process.

scholarly journals Multiaxial fatigue behavior of 2618 aluminum alloy

2019 ◽  
Vol 300 ◽  
pp. 09003
Author(s):  
Benaïssa Malek ◽  
Catherine Mabru ◽  
Michel Chaussumier
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Internal Pressure ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Multiaxial Fatigue ◽  
Mean Stress ◽  
Research Project ◽  
Pressure Tests

The purpose of the present research project is to study multiaxial fatigue behavior of 2618 alloy. The influence of mean stress on the fatigue behavior under tension and torsion is particularly investigated. Fatigue tests under combined tensile-torsion, in or out of phase, as well as combined tensile-torsion-internal pressure tests have also been conducted. Multiaxial fatigue results are analyzed according to Fatemi-Socie criterion to predict the fatigue life.

scholarly journals Effect of UV Ageing on the fatigue life of bulk polyethylene

2018 ◽  
Vol 165 ◽  
pp. 08002 ◽  
Author(s):  
Hamza Lamnii ◽  
Moussa Nait-Abdelaziz ◽  
Georges Ayoub ◽  
Jean-Michel Gloaguen ◽  
Ulrich Maschke ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Uv Irradiation ◽  
Chemical Structure ◽  
Fatigue Behavior ◽  
Crystalline Polymer ◽  
Fatigue Loading ◽  
Chain Scission ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Irradiation Effect

Polymers operating in various weathering conditions must be assessed for lifetime performance. Particularly, ultraviolet (UV) radiations alters the chemical structure and therefore affect the mechanical and fatigue properties. The UV irradiation alters the polymer chemical structure, which results into a degradation of the mechanical and fatigue behavior of the polymer. The polymer properties degradation due to UV irradiation is the result of a competitive process of chain scission versus post-crosslinking. Although few studied investigated the effect of UV irradiation on the mechanical behaviour of thermoplastics, fewer examined the UV irradiation effect on the fatigue life of polymers. This study focuses on investigating the effect of UV irradiation on the fatigue properties of bulk semi-crystalline polymer; the low density Polyethylene (LDPE). Tensile specimens were exposed to different dose values of UV irradiation then subjected to fatigue loading. The fatigue tests were achieved under constant stress amplitude at a frequency of 1Hz. The results show an important decrease of the fatigue limit with increasing absorbed UV irradiation dose.

Sign in / Sign up

Export Citation Format

Share Document