Destructive Vibration of Trashracks due to Fluid-Structure Interaction

1975 ◽  
Vol 97 (4) ◽  
pp. 1359-1365 ◽  
Author(s):  
S. H. Crandall ◽  
S. Vigander ◽  
P. A. March
Keyword(s):  
Vortex Shedding ◽  
Storage System ◽  
Water Channel ◽  
Scale Model ◽  
Original Design ◽  
Cross Sectional ◽  
Flow Rates ◽  
Pumped Storage ◽  
Sectional Shape ◽  
Lock In

Trashracks in pumped storage systems with high flow rates can develop fatigue failures due to excessive vibration excited by the flow past the rods in the rack. An experimental study of trashrack vibration was made on a half-scale model of a prototype rack design for the TVA Raccoon Mountain pumped storage system. The natural frequencies and loss factors of the first dozen natural modes of the rack were determined in air before placing the rack in a water channel. Under normal flow rates the rack developed “locked-in” pure tone vibrations of sufficient amplitude to cause early fatigue failure. Unexpectedly, the frequency of the vibration was not close to the vortex-shedding frequency and the motion of the rods was not transverse to the flow. The “locked-in” modes were identified as modes in which the bending displacements of the rods were parallel to the flow. Further investigation showed that the excitation mechanism involved synchronization between the fluctuating drag involved in vortex shedding and the fore-and-aft motion of the rods in sharply resonant modes. Modifications of the original design were introduced to defeat the identified mechanism. In order to completely eliminate the “lock-in” phenomenon it was necessary to change the bar cross-sectional shape and to introduce additional damping into the rack structure. A half-scale model of the modified design was built and tested to verify the absence of destructive vibrations.

Cross-sectional shape effect of a diffuser micropump on flow rates

2011 ◽  
Vol 6 (8) ◽  
pp. 682 ◽  
Author(s):  
Chang-Ju Park ◽  
Byung-Phil Mun ◽  
Sung-Keun Yoo ◽  
Jong-Hyun Lee
Keyword(s):  
Shape Effect ◽  
Cross Sectional ◽  
Flow Rates ◽  
Sectional Shape

scholarly journals Multi-branching three-dimensional flow with substantial changes in vessel shapes

2008 ◽  
Vol 614 ◽  
pp. 329-354 ◽  
Author(s):  
R. I. BOWLES ◽  
N. C. OVENDEN ◽  
F. T. SMITH
Keyword(s):  
Three Dimensional ◽  
Longitudinal Vortex ◽  
Cross Sectional ◽  
Flow Rates ◽  
Relative Flow Rate ◽  
Wide Range ◽  
Flow Through ◽  
Sectional Shape ◽  
Area Expansion ◽  
Reversed Motion

This theoretical investigation of steady fluid flow through a rigid three-dimensional branching geometry is motivated by applications to haemodynamics in the brain especially, while the flow through a tube with a blockage or through a collapsed tube provides another motivation with a biomedical background. Three-dimensional motion without symmetry is addressed through one mother vessel to two or several daughters. A comparatively long axial length scale of the geometry leads to a longitudinal vortex system providing a slender-flow model for the complete mother-and-daughters flow response. Computational studies and subsequent analysis, along with comparisons, are presented. The relative flow rate varies in terms of an effective Reynolds number dependence, allowing a wide range of flow rates to be examined theoretically; also any rigid cross-sectional shape and ratio of cross-sectional area expansion or contraction from the mother vessel to the daughters can be accommodated in principle in both the computations and the analysis. Swirl production with substantial crossflows is found. The analysis shows that close to any carina (the ridge separating daughter vessels) or carinas at a branch junction either forward or reversed motion can be observed locally at the saddle point even though the bulk of the motion is driven forward into the daughters. The local forward or reversed motion is controlled, however, by global properties of the geometry and incident conditions, a feature which applies to any of the flow rates examined.

scholarly journals Underground Pumped-Storage Hydropower (UPSH) at the Martelange Mine (Belgium): Underground Reservoir Hydraulics

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3512 ◽  
Author(s):  
Vasileios Kitsikoudis ◽  
Pierre Archambeau ◽  
Benjamin Dewals ◽  
Estanislao Pujades ◽  
Philippe Orban ◽  
...  
Keyword(s):  
Water Level ◽  
Renewable Energy Sources ◽  
Storage System ◽  
Cross Sectional Area ◽  
Abandoned Mines ◽  
Sectional Area ◽  
Cross Sectional ◽  
Underground Reservoir ◽  
Total Cross Sectional Area ◽  
Pumped Storage

The intermittent nature of most renewable energy sources requires their coupling with an energy storage system, with pumped storage hydropower (PSH) being one popular option. However, PSH cannot always be constructed due to topographic, environmental, and societal constraints, among others. Underground pumped storage hydropower (UPSH) has recently gained popularity as a viable alternative and may utilize abandoned mines for the construction of the lower reservoir in the underground. Such underground mines may have complex geometries and the injection/pumping of large volumes of water with high discharge could lead to uneven water level distribution over the underground reservoir subparts. This can temporarily influence the head difference between the upper and lower reservoirs of the UPSH, thus affecting the efficiency of the plant or inducing structural stability problems. The present study considers an abandoned slate mine in Martelange in Southeast Belgium as the lower, underground, reservoir of an UPSH plant and analyzes its hydraulic behavior. The abandoned slate mine consists of nine large chambers with a total volume of about 550,000 m3, whereas the maximum pumping and turbining discharges are 22.2 m3/s. The chambers have different size and they are interconnected with small galleries with limited discharge capacity that may hinder the flow exchange between adjacent chambers. The objective of this study is to quantify the effect of the connecting galleries cross-section and the chambers adequate aeration on the water level variations in the underground reservoir, considering a possible operation scenario build upon current electricity prices and using an original hydraulic modelling approach. The results highlight the importance of adequate ventilation of the chambers in order to reach the same equilibrium water level across all communicating chambers. For fully aerated chambers, the connecting galleries should have a total cross-sectional area of at least 15 m2 to allow water flow through them without significant restrictions and maintain similar water level at all times. Partially aerated chambers do not attain the same water level because of the entrapped air; however, the maximum water level differences between adjacent chambers remain relatively invariant when the total cross-sectional area of the connecting galleries is greater than 8 m2. The variation of hydraulic roughness of the connecting galleries affects the water exchange through small connecting galleries but is not very influential on water moving through galleries with large cross-sections.

On the cross-sectional shape of the cellulose crystallites in the tunicate Halocynthia papillosa

1990 ◽  
Vol 48 (3) ◽  
pp. 566-567
Author(s):  
J.-F. Revol ◽  
Y. Van Daele ◽  
F. Gaill
Keyword(s):  
Contrast Imaging ◽  
Animal Kingdom ◽  
Bright Field ◽  
Field Mode ◽  
Cross Sectional ◽  
Ultrathin Sections ◽  
The Cross ◽  
Sectional Shape ◽  
Valonia Ventricosa ◽  
C Nmr

The only form of cellulose which could unequivocally be ascribed to the animal kingdom is the tunicin that occurs in the tests of the tunicates. Recently, high-resolution solid-state l3C NMR revealed that tunicin belongs to the Iβ form of cellulose as opposed to the Iα form found in Valonia and bacterial celluloses. The high perfection of the tunicin crystallites led us to study its crosssectional shape and to compare it with the shape of those in Valonia ventricosa (V.v.), the goal being to relate the cross-section of cellulose crystallites with the two allomorphs Iα and Iβ.In the present work the source of tunicin was the test of the ascidian Halocvnthia papillosa (H.p.). Diffraction contrast imaging in the bright field mode was applied on ultrathin sections of the V.v. cell wall and H.p. test with cellulose crystallites perpendicular to the plane of the sections. The electron microscope, a Philips 400T, was operated at 120 kV in a low intensity beam condition.

Automated 3D measurement of fiber cross section morphology in handsheets

2012 ◽  
Vol 27 (2) ◽  
pp. 264-269 ◽  
Author(s):  
Christian Lorbach ◽  
Ulrich Hirn ◽  
Johannes Kritzinger ◽  
Wolfgang Bauer
Keyword(s):  
Image Analysis ◽  
Cross Section ◽  
Cross Sections ◽  
Image Plane ◽  
3D Measurement ◽  
Cross Sectional ◽  
Fiber Cross Section ◽  
Fiber Wall ◽  
Sectional Shape ◽  
Cross Section Geometry

Abstract We present a method for 3D measurement of fiber cross sectional morphology from handsheets. An automated procedure is used to acquire 3D datasets of fiber cross sectional images using an automated microtome and light microscopy. The fiber cross section geometry is extracted using digital image analysis. Simple sample preparation and highly automated image acquisition and image analysis are providing an efficient tool to analyze large samples. It is demonstrated that if fibers are tilted towards the image plane the images of fiber cross sections are always larger than the true fiber cross section geometry. In our analysis the tilting angles of the fibers to the image plane are measured. The resulting fiber cross sectional images are distorted to compensate the error due to fiber tilt, restoring the true fiber cross sectional shape. We use an approximated correction, the paper provides error estimates of the approximation. Measurement results for fiber wall thickness, fiber coarseness and fiber collapse are presented for one hardwood and one softwood pulp.

Validation of mathematical model of electrothermal calculation of DC catenary on the basis of scale model

2018 ◽  
Vol 77 (4) ◽  
pp. 222-229 ◽  
Author(s):  
A. V. Paranin ◽  
A. B. Batrashov
Keyword(s):  
Mathematical Model ◽  
Operating Conditions ◽  
Scale Model ◽  
Contact Network ◽  
Scaled Model ◽  
Cross Sectional ◽  
Current Collection ◽  
Topological Features ◽  
Study Results ◽  
Real Physical Process

The article compares the results of calculation of the finite element simulation of current and temperature distribution in the scale model of the DC catenary with the data of laboratory tests. Researches were carried on various versions of the structural design of catenary model, reflecting the topological features of the wire connection, characteristic of the DC contact network. The proportions of the cross-sectional area of the scaled model wires are comparable to each other with the corresponding values for real DC catenary. The article deals with the operating conditions of the catenary model in the modes of transit and current collection. When studying the operation of the scale catenary model in the transit mode, the effect of the structural elements on the current distribution and heating of the wires was obtained. Within the framework of the scale model, theoretical assumptions about the current overload of the supporting cable near the middle anchoring have been confirmed. In the current collection mode, the experimental dependences of the current in the transverse wires of the scale model are obtained from the coordinate of the current collection point. Using the model it was experimentally confirmed that in the section of the contact wire with local wear, not only the temperature rise occurs but also the current redistribution due to the smaller cross section. Thus, the current share in other longitudinal wires of the scale model increases and their temperature rises. Scale and mathematical models are constructed with allowance for laboratory clamps and supporting elements that participate in the removal of heat from the investigated wires. Obtained study results of the scale model allow to draw a conclusion about the adequacy of the mathematical model and its correspondence to the real physical process. These conclusions indicate the possibility of applying mathematical model for calculating real catenary, taking into account the uneven contact wear wire and the armature of the contact network.

Study of Correctly Expanded Sonic Jet with Air Tabs

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Arun Prasad R ◽  
Thanigaiarasu S ◽  
Sembaruthi M ◽  
Rathakrishnan E
Keyword(s):  
Numerical Study ◽  
Cross Sectional ◽  
Potential Core ◽  
Convergent Nozzle ◽  
Jet Mixing ◽  
Pressure Profiles ◽  
Constant Diameter ◽  
Sonic Jet ◽  
Sectional Shape ◽  
Length Reduction

AbstractThe present numerical study is to understand the effect of air tabs located at the exit of a convergent nozzle on the spreading and mixing characteristics of correctly expanded sonic primary jet. Air tabs used in this study are two secondary jets issuing from constant diameter tubes located diametrically opposite at the periphery of the primary nozzle exit, normal to the primary jet. Two air tabs of Mach numbers 1.0 to 1.4, in steps of 0.1 are considered in this study. The mixing modification caused by air tabs are analysed by considering the mixing of uncontrolled (free) primary jet as a reference. Substantial enhancement in jet mixing is achieved with Mach 1.4 air tabs, which results in 80 % potential core length reduction. The total pressure profiles taken on the plane (YZ) normal to the primary jet axis, at various locations along the primary jet centreline revealed the modification of the jet cross sectional shape by air tabs. The stream-wise vortices and bifurcation of the primary jet caused by air tabs are found to be the mechanism behind the enhanced jet mixing.

Experimental investigation and optimization on field shaper structure parameters in magnetic pulse welding

2021 ◽  
pp. 095440542110148
Author(s):  
Yingzi Chen ◽  
Zhiyuan Yang ◽  
Wenxiong Peng ◽  
Huaiqing Zhang
Keyword(s):  
Magnetic Field ◽  
High Speed ◽  
Light Metal ◽  
Magnetic Pulse ◽  
Cross Sectional ◽  
Magnetic Pulse Welding ◽  
Pulse Welding ◽  
Sectional Shape ◽  
Welding System ◽  
The Magnetic Field

Magnetic pulse welding is a high-speed welding technology, which is suitable for welding light metal materials. In the magnetic pulse welding system, the field shaper can increase the service life of the coil and contribute to concentrating the magnetic field in the welding area. Therefore, optimizing the structure of the field shaper can effectively improve the efficiency of the system. This paper analyzed the influence of cross-sectional shape and inner angle of the field shaper on the ability of concentrating magnetic field via COMSOL software. The structural strength of various field shapers was also analyzed in ABAQUS. Simulation results show that the inner edge of the field shaper directly affects the deformation and welding effect of the tube. So, a new shape of field shaper was proposed and the experimental results prove that the new field shaper has better performance than the conventional field shaper.

Sign in / Sign up

Export Citation Format

Share Document